Community Brag Posts

Pedestal Table

This is a variation on the tidy up end table. The dimensions for the tidy up end table were too big for my space, so I made it a little smaller and added an extra shelf to store our laptop computers. This makes it easier to charge our laptops and keep them out of the way. It took me a little longer than it should have because I had a 3 year old and a 5 year old "helping" me.

Build Instructions;

http://www.instructables.com/id/Rain-Barrel-Stand-and-Installation/

Video of Build:

https://www.youtube.com/watch?v=LvSJxXqfP68

We are selling our house and needed a small table for the corner of our kitchen. Since we had leftover butcher block after replacing the countertops, I modified the Farmhouse Table and bench plans. The piece worked perfectly in the space and the house sold immediately after our open house.

My first attempt at a real furniture project, I would have never tried this without all the plans and support here at Ana-White! These are 7' for the kitchen/breakfast area.  Since the table is only 7', it has 2 pedestals.  I modified these a bit from the triple pedestal farmhouse bench and table plans by using a runner along the floor instead of a stringer board on the table and adding triple feet on the outside pedestals.   I also added 1x3 trim under the arches to add some detail and hide the grooves between the three 2x4 leg supports.  The top has mitered 2x4s around the outside with 1x6s on the inside.  One issue I ran into was that the 2x4s shrank a lot as they dried, while the kiln-dried 1x6s did not.  To make an easier to clean surface I planed the top smooth, and then added minimal texture by hand scraping.  My plan is to build a big 12' version of this table for the dining room. 

I loved Ana's version of the coffee table but it was way too big for my space, so I scaled it down quite a bit and it fits perfectly!

I made this entry table to go by our front door. It's a spin off from the "console table" posted by Anna. I read some of the comments from people who had problems with her plans as a result of different standards in lumber and decided to alter this some!

I cut the side braces short enough so when I included the measurements of the legs the actual table top extended approx. 3/4" further past the legs and apron of the table. I also went with one sheet of wood on the table top and finished it up with some trim around the edge of the table top.

a few face grain "catering/presentation" boards i made.  16x28

2 for my culinary graduation and 2 for a freinds business

This table is made out of Solid Oak and took me +- 6 weeks to complete.

Thanks to Ana White for the plans as I followed them to the "t" with some minor changes in the size

Final size is 10ft long x 47 1/4 inch wide and 29 9/64 inches high

I took the Simple Outdoor Table along with a table I had seen at Pottery Barn and kind of put this together. It made of cedar and stained with a natural to keep the pretty color.

I essentially stuck to the main plan - except to support the wings I used 2X2 boards and standard hinges.

I was worried that there may not be enough space for my Ryobi 10" sliding miter saw because of the slide however, it fits nicely and there is plenty of space.

Thank you for the wonderful plan. This was my first project of this size and I am very happy with the results!

Made two of these chairs for my little girls. The second one I managed to conceal all the screws too.

This table follows the plan pretty closely except that I wanted to use Red Cedar because of its beauty and durability. We can only get Red Cedar at one National Chain here and it only came in 6" widths, which meant a few recalculations. We also used deck strips (as recommended at the store) to attach the top from underneath (shown in photo) and adjusted the screw length to accommodate. We were able to keep waste to a minimum (seen in photo with triangle) by making sure to cut varying lengths from the boards (ie. one board gave us the length and width of the table). This was made easier by the available lengths of board from the store (8', 10', 12'). Another recommendation from the store was to use coated screws with cedar to prevent black streaks over time.
I love my new table!