Community Brag Posts

Queen size head board.

Made of old fence rail (the dark pieces) and cheap 2x4s and 1x12s .

This is not as stable as I hoped, but for an afternoon's project that got all those tools off the workshop floor, it's not bad. I will add a diagonal brace at the back later. Much later.

NOTE: My engineer friend notes that 2 braces at the rear, below the bottom shelf and below the top shelf, would minimize side-to-side wobbling, and 2 braces front to back, both under the bottom shelf, would minimize the front-to-back wobbling, They could be a scrap of plywood, a 1x6 or wider scrap. Just nail them in two or more places on each of the ladders and they make the structure more rigid. Screw them in if you want a shelf unit you can disassemble.

TIPS:
If you are using pockethole screws, start the screws in all the holes before you put the crosspieces on. Stop when you see the tip of the screw come through the first piece.

Clamp scrap 2x4 to the uprights to hold the crosspieces in place as you drill.

To get the shelves in place, lean the ladders against each other and attach the bottom and top boards on one side. Than pull the other ladder out as far as it needs to go and screw that side of the shelves in place.

Don't try this without clamps.

It could have been cheaper if I had used all reclaimed fence 2x4s, and if my errand runner had bought cheaper 1x12s. He bought top-grade when #2 would have worked for half the price,

This was my first project, my wife and I started with the table, which took us a little while but ended up being pretty simple. Unfortunately we do not own a saw but discovered that Lowes will happily cut the wood for you. After we completed the table we started working on the bench, which is where we ran into a slight problem. Some how our frame boards ended up being two short, so as a fix we did not put any spaces in between the seat slats and used four 7 inch pieces we had left over to complete the full frame. We also altered the plan to make our bench a little longer than the original its 57 inches instead of 52.

This leaning shelf was the perfect solution to my tiny (and tiled) bathroom. I didn't want to have to put screw holes in the walls and have been searching for a project. 

I made the shelves out of reclamed barn wood which made the project a little bit harder to get perfect square and level but it was worth it. The legs are 2x4s. The hardest part was definitely making sure the shelves were level on the legs. Lots of clamps helped! 

I have used your plan, to build several of the 2x4 Adirondack chairs, made a few modifications here and there but basically the same frame.

Very sturdy and stylish step stool built for my son in a style to match the kitchen and bathroom in our house.

This entire project was built using scrap plywood from a previous project and reclaimed oak boards that we demoed from our house while remodeling.

The sides were simply cut using a table saw to the rough dimension and then I added the details using a bandsaw. The stairs and rails were rough cut on the tablesaw and then milled using a jointer and planer to the specifications in the plan. Once cut I used a pocket screw jig to drill all the necessary holes before finishing assembly on the base. Each section was finished separately and then I used pocket screws to attach the steps last.

Very easy project that I made slightly more complicated by using reclaimed wood and a 2 tone design. Would recommend pocket screws to ensure strength and durability...I can stand on this and it doesn’t even budge!

Thanks for the plans!!

I used the bench top from Ana's Farmhouse Table and took 1.5in off the legs to compensate.  Got the baskets on Amazon.

Made this out of free wood I got from my workplace.

Chairs made as birthday gifts.

We adjusted the plan and created a 4x7 sand box with toy box and canopy. We are in love with the way this has turned out!

Thank you for the detailed plans and step by step pictures!

We wanted outdoor furniture but did not want to pay over $500. Very sturdy and will last forever!

These picture frames are inspired by furniture and frames made from
reclaimed boat wood which came from fishing villages in many parts of
the world. The frames here are made from readily available materials – the humble fence wood boards, some stores call it lathe. An 8' long piece only cost $1-$2. The complete detailed tutorial is here- http://www.apieceofrainbow.com/diy-make-beachy-style-picture-frames-from-fence-wood/

I did not have any plans for this.  I had the dimensions from the West Elm Website so I did my best to match that.  My sister asked me if I could build this for her and I saw it as an awesome challange.  I used euro style hinges for the doors and the left side shelf is sitting on wood strips nailed in the sides.  There is also a shelf inside the cabinet.  I built the stand and she stained it.  

This was my second time welding.  I used a Mig Welder that my buddy had.  It was a little intimidating at the very beginning but Mig welding is super easy.  You can grind the welds down fairly easy too.  I sray painted it all with a flat black spray paint.  I think it turned out really well.  I had a steel shop her in town cut all the steel to the sizes I needed.  All I had to do was weld and paint.

I used dowels in the screw holes.