1. Home
  2. Plan Catalog

Rustic X Coffee Table

|save this plan
Submitted by Ana White on Tue, 07/09/2019 - 10:40
Difficulty
Intermediate
| Print this plan

You can build a beautiful coffee table out of lumber!  For about $50 in materials, this solid wood coffee table with it's X detailing could be yours.  Our free plans include step by step diagrams, shopping lists and cut list - everything you need to get started.

Also in this collection: Rustic X Console Table, Rustic X End Table, and Rustic X Bench Plans

Collections
Rustic X Collection
rustic x coffee table plans
rustic x coffee table plans
rustic x coffee table plans
rustic x coffee table plans
rustic x coffee table plans
rustic x coffee table plans

Beginner Friendly Option

With the popularity of this plan, we have created a Beginner Friendly plan that is very similar.  It uses less tools and the overall cost is under $40.

farmhouse coffee table

The beginner plan is slightly smaller and has a slatted bottom shelf.  You can find the plans here.

Rustic X Coffee Table Plans

Remember a bit back when Hillary  from The Friendly Home built this amazing Rustic X Console Table from 2x4s? 

We've had so much interest from readers, we thought we'd add a coffee table plan to the collection.  

This coffee table is so gorgeous, it's hard to believe it's made from standard off the shelf lumber!

I ENCOURAGE you to stop over and visit Hillary and read about how she battled a wild fire to build this coffee table!  

PS - Hillary is also sharing her finishing tutorial.

Dimensions
rustic x coffee table dimensions
Dimensions are shown above

Preparation

Shopping List
  • 2 – 2x4 – 8 feet or stud length
  • 4 – 2x2 – 8 feet
  • 1 – 1x12 – 8 feet long
  • 5 – 2x6 – stud length
  • 1 ¼” and 2 ½” Pocket Hole screws
Cut List
  • 4 – 2x4 @ 16 ½” (legs)
  • 4 – 2x2 @ 41” (side trim)
  • 4 – 2x4 @ 22 ½” (end trim)
  • 2 – 1x12 @ 41” (bottom shelf)
  • 2 – 2x2 @ 22 ½” (both ends cut at 60 degrees off square, long point to short point, ends are parallel)
  • 4 – 2x2 @ 11 ¼” (long point to short point, one end cut at 60 degrees off square, other end cut at 30 degrees off square, ends are not parallel but are cut in same direction)
  • 5 – 2x6 @ 52” (tabletop boards)
Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Miter Saw
Brad Nailer
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

First build the two side trim pieces.

Step 2

Then connect together. Hide top pocket holes on top, bottom pocket holes on bottom. NOTE: This plan is sized for 1x12 boards measuring 11 1/4" wide - measure your 1x12 boards, double that number, and cut your side trim to fit - see next step.

Step 3

Build your bottom shelf with 3/4" PHs/1 1/4" PH screws down center. Then drill 3/4" PHs around all outside edges and attach to the bottom shelf.

Step 4

Now attach cut and build the X braces. Attach in place. These are mostly decorative, so don't stress about getting them super screwed in place. Some good glue and screws will do the trick.

Step 5

For the top, we recommend building the entire top with 1-1/2" pocket holes and 2-1/2" pocket hole screws on a flat level surface.

Then attached the completed top to the base.
 

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Project Type
Coffee Tables
Room
living room
Style
Farmhouse Furniture
Rustic Furniture Plans

Comments

bigskyvideo

Wed, 04/22/2020 - 18:38

I'm building this in the next few days, but I don't understand the bottom shelf. Is there really nothing to support the middle seam of the bottom shelf? It seems like it will flex and collapse with any weight.

bigskyvideo

Wed, 04/22/2020 - 18:40

I'm building this in the next few days, but I don't understand the bottom shelf. Is there really nothing to support the middle seam of the bottom shelf? It seems like it will flex and collapse with any weight.

scrocchi

Sat, 05/30/2020 - 22:59

Does anyone know what wood stain was used for the coffee table? The link that's been posted previously doesn't work anymore.

sallison20

Wed, 08/05/2020 - 18:42

What hardware is shown in the example picture? I didn't see hardware listed in the buy list.

jacksonm

Thu, 08/27/2020 - 08:05

Hi.
I love your table. I just recently purchased all the wood I need to build it.
I have a question regarding the decorative bolts and corner braces. Where did you buy them? I've been looking around but have had no luck. I'd appreciate your input.

Thanks so much!