Community Brag Posts

2 years ago I mad a TV stand that was nice. I decided to make a new one now that I know more about wood work. First one was made from Lowes top choice oak plywood and took a lot of work. I have discovered real hardwood stores and for plywood I like Baltic Birch.

I didn't  make any hard plans for this one, made it by ear. 2 sheets of 5x5 18mm (3/4) 1/2 sheet of 12mm (1/2) and a 1/2 sheet of 6mm (1/4) Baltic. For edging I left the baltic alone and just rounded it over.

60'wx20"dx 28h

I modified the plans from the storage bed to create two benches according to the sizes I needed. The benches were arranged in an L formation and secured to the walls and to a base that I built from 2x4s. I made overlay (correct terminology?) drawers using accuride drawer slides that were super easy to install. Floor molding around the base and some 1x2s for the trim. Drawer handles from the depot. Custom cushions ordered online (I can't sew and yes this was the most expensive part of the project). Pillows from Kohl's with free ship and a 30% off coupon - whoo hoo!

We used Behr cloud burst for the colour and Minwax special walnut for the stained platform.  I hand drew and painted the owl (the wings are scrapbook paper) and coated with three coats of polyurethane.

It was very easy to follow the directions and the costs were minimal. Our granddaughter is in heaven with this bed. 

This table and bench combo was a fun project to complete and was not very difficult (hardest part was picking out straight boards at the lumber yard). The table was stained with weathered oak stain and finished with satin polycrylic. The chairs were purchased, I am not skilled enough to build those!

Thanks again to Ana for the instructions. It turned out great!

This is my scaled down version of the preschool picnic table, made for an 18 inch doll. I used scrapwood that someone was throwing away and supplies left over from other projects, so it didn't cost anything but time. My girls have really enjoyed it. Here are the measurements: 

Cut List: 

4 – 1×3 @ 17-3/4″ (Tabletop pieces) 

1- 1×4 @ 9-3/4″, then cut in half using a table saw to equal 2 pieces (Supports directly beneath tabletop pieces) The longest measurement is 9 ¾”, with the ends cut at a 30 degree angle back to 7 3/4″.

2-1×4 @ 12-7/8”, then cut in half using a table saw to equal 4 pieces (Legs) (angle each end to 30 degrees as shown in preschool table plans) 

1 – 1×4 @ 19″, then cut in half using a table saw to equal 2 pieces (Supports directly beneath seat boards)  (angle ends to 30 degrees as shown in preschool table plans)

4 – 1×3 @ 17 3/4″ (Seat boards) I ran these 1 x 3’s through my table saw to make them 2” wide.

*When attaching the legs, secure them to the supports below the tabletop pieces so that the bottom of the legs will measure 19 5/8” from lateral edge to lateral edge when resting on the ground. In the preschool picnic table plans, this measurement is shown as 33”.

made this farmhouse table 30in tall 4ft long and 26in wide,

I wrote a blog entry about this project that you can find at:

https://1thing1week.com/2017/01/09/airplane-shelf-for-a-nursery/

This shelf is great for beginners, easy to assemble and very inexpensive! I had a blast making it. I made it for my expected son's airplane themed nursery. 

I started with Ana's "Mom's Train Table" design and added a bit of western design to it. I also added two drawers instead of the empty space to store the train set and other toys to be played with on it when the coffee table top is on. The train table top is also loose in the space, so it can be swapped out or flipped over for another design, farm, train, city, racetrack, etc.

I used and existing toddler bed frame and repurposed it as a trundle bed so we could add a 3rd bed into our kids small bedroom.  You can easily make the bed frame too.

Check out my blog post with steps on how to turn a toddler bed into a trundle.  Great space saver and it's much easier to pull out from under the bed on the carpet (and easier than a full size trundle).

http://www.tools4moms.com/2012/07/diy-toddler-trundle.html

I was eager to start this project and was super stoked with how it turned out. Can't wait for more inspiration to continue building beautiful furniture. Thanks

I used the Kreg Jig to permanently mount each shelf (two pocket holes per shelf).

Emerson with extra trim and fancy feet. Also added a closet dowel and overhang.  Built at 36 weeks for our baby Collin.

We were desperate for organization in my son's room. This was an easy project for beginners.