Community Brag Posts

My wife found this plan so I decided to tackle it. Spent about $80 in supply's and had some 2x8s from a shed we tore down. Planed them down and made this beautiful piece. Now my wife can't get me out of the kitchen. Sorry for the mess in the back ground.

Camp Loft Bed with Stairs/Junior Height

We (hubby & myself) found these plans on your site and thought the bed would be perfect for our 13 year old son with special needs. He's been sleeping on a queen bed, but also had a privacy tent in our front room when he wanted to be alone. He never went into his bedroom unless he was sleeping for the night.
We decided to keep the queen mattress for him on the bottom, but wanted to save as much floor space as possible. We put a twin xl mattress on the top (added 5 inches to length), so the queen could fit underneath in the same direction. We built a headboard for the lower queen (1 x 6s) and added accessories like a light, cup holders, small shelf and a book holder to compensate for the nightstands we removed from his room. We decided to purchase a three inch bedframe for the queen in case the bottom space is used differently in the future.
Since our son needs extra stability, we added stair treads and a hand rail to the stair/platform area. We didn't want the space underneath the platform to go to waste. It is perfect for his stuffed animals. I used eye hooks and bungee cord to create a safe enclosure for them.
In order to provide him with the ultimate privacy, we used 4 x 4s for the bed posts and ran them up to the ceiling. This allowed us to run blackout curtains on the front and on one end of the upper structure. We also installed a light on the top level.
The instructions were great, especially the cut list. I can't give you a project time. Due to our schedules, we built it relay race style. My husband picked up the wood, and I cut it while he was working. He'd have some time to router the edges, and I would sand (80/150/220 grit), prime and paint all of the pieces. We worked together to assemble the bed in our son's room. I finished areas that needed filling/painting and added the accessories.
We are very happy with the results. This bed changed the whole dynamic of the room, and our son is finally hanging out in there.

After a lot of cutting, screwing, chiseling and sanding... oh and a lick of paint! My new little Saddle Seat Stools are complete. Time will only tell whether they will hold up to the abuse the boys give them especially Brodie! These new stools only cost me $48 to make the pair and I got all the timber from Bunnings

Awesome plan for kids play room!

Thank you so much for sharing your tutorials, I find you projects easy to follow and have made some but we just got our 1st puppy in a while since our last past away a few years ago, her name is Maggie and she is a golden doodle, and she is adorable and only 12 weeks old. We needed something to put her in when we go to work so I took your double design and made it work for us. 60” wide with a single door in middle, plan on having a bed to left and eating to right and I left it open like your plans for a pan or mat for accident s as I’m sure will happen. I took the bars and spaced them 3” apart but 2 areas by the door are about 3.5” and she can slip through still need to add a few more bars so she don’t but again thanks love your projects

This table and bench combo was a fun project to complete and was not very difficult (hardest part was picking out straight boards at the lumber yard). The table was stained with weathered oak stain and finished with satin polycrylic. The chairs were purchased, I am not skilled enough to build those!

My fiance and I built this for my seven year old daughter's Christmas present. I have built several pieces of furniture before but this was our first major building project and I'm proud to say we made a great team!

We didn't make any major changes to the plan, we just chose to leave the wheels off the bottom and we added two boards across the back of the attic rooms so we would have something to attach the back too. We were lucky enough that this project coincided with my dad have his roof replaced and he had spare shingles, so her doll house has real asphalt shingles! They were actually a lot easier to add than I expected, we simply scored the back of the shingles with a knife and then they cleanly broke apart. We used a staple gun to attach the shingles we would be able to layer so you couldn't see the staples, but for those where the staples would have shown we used a hot glue gun.

The only issue we had was moving it around without my daughter noticing because it's so big! My fiance and I actually scratched up a door frame trying to sneak it under the tree after she went to sleep because it's so large (totally my fault, apparently I need to work out more). Other than that everything went smooth and it was fun to build and so exciting to watch my daughter freak out over Christmas morning!!!

Thanks for the inspiration!  This was my first full blown creation and my wife loves it.  Cannot wait to do more!

This was just the right table design for our history home built in 1880! Love the plans and easy to build!

Built the corner hutch from Ana's super easy plans!  LOVE IT!

http://www.ana-white.com/2010/12/plans/corner-cupboard

Made a cutout for my thermostat on the wall.  Gotta love building what you need for your space!

This project was super easy, my husband and I did this together while I was 9 months pregnant with our other 2 kids and dog running around the whole time! We made the table and 2 benches for $250 including lumber and finishing supplies. Check out my blog for details.

I used the Farmhouse Table plans and just extended the measurements to build an extra-long outdoor table that seats 12.

I loved building this bench!!  I was able to use only 6 2x4's which cut down the cost a little bit :)  For the stain I used Semi-Transparent Chocolate from HD and Wedgewood in a Solid Stain color from HD as well.  Building the bench itself was really easy but the X's do take some extra work.  I found that using a yard stick vs. a tape measure made the world of difference.  I also nailed the X's in vs. using the kreg jig. 

Made this one with shelf edges/trim just on the sides. Somehow my top shelf didn't span the width so had to add a little shim on each side but it all worked out! We had all the pallets and used 1x3s for the frame because some of my pallet wood was heavy hardwood. It was not without frustration because I was working with uneven/warped pallet wood but it hits the rustic look.  I am happy with how it turned out.