Community Brag Posts

How to build a Bottle Cap Tray AND what NOT to do.

These Bottle Cap Trays are sold for 45+ Bucks online. I spend maybe 15$ on it.

You need a lot of Friends drinking a lot of different Beers... For this tray i needed 88 Caps. I also asked Bartenders and Co-Workers to collect Caps. As more colorfull you get as better. Twist off Caps are the best behause they do not have dents.

I bought the Tray at Hobby Lobby for 3.99$ (you can also build one from a Plan from this Side) and after sanding with 220Grid i stained it to fit my Home Bar. After lay out the "Design" i removed them all and lay them in the back of the now empty tray.

2 Ways to glue the Caps to the Board:

1. Hot Glue (be carefull the Caps get very Hot)
2. I poured just a small amount of the Epoxy in there and pushed the Caps into the Ressin...

How to mix Ressin...

Read the Manuall!!! The first 2 Trays i poured to much and then it gets very very hot and ruin everything (see second last Picture). 2nd Glue the board to the Walls, if the Ressin runs out of the Tablet it is also a great mess!

I Used 2 small cups messured it and Mixed it in the Red Solo Cup...

Put the Tablet on an even surface (protect it) and pour a small amount into the tray... Level it and then put the Caps in there and use a torch to get rid of the Air Bubbles. I needed 3 layers to Cover all Caps. Keep it Dustfree during curing - very important .

I let it cure for 12 Hours bevor the next layer was applied. Total Curie after 72 Hours...

Sorry for Bad English - i am German...

Hope that helps to build your own Bottle Cap Tray...

And made it as colorfull as possible. I aranged them to face One Side but you also can turn them happy around.

Thanks for comments and Reading

Jann

This was a very fun project to build. I pretty much followed the directions that were posted, but I used 1x6's instead of 1x4's because I wanted more storage space on the shelves. I also used 1/2" iron piping instead of 3/4" and am happy with how it turned out. Since the guest bathroom is gray, we didn't want to stain the wood and chose to do an easy to do "weathered" (directions below) look. Now all we need to do is replace the ugly shower curtain!

This took about a week to complete.  I modify the original plan to include "built in" dressers and a night stand type of dresser.  The night stand has shelves built on the side.     Two beds were built of different configurations.  

We modified the plan and made many changes along the way and here’s our finished island. We’re thrilled!

For my second project I wanted to build something a little more difficult than a shelf.  The hubby showed me how to use our power tools and I was unstoppable.  I chose this great bench because it fit the feel of our house and I wanted an entryway spot to sit while putting on shoes. 
The finishing took much longer than it actually took to build the bench.  I thought it would be more difficult to get the precise angle measurements  to make the supports under the bench, but it was not bad at all.  I can 't believe I built this pretty bench!  I have the building fever now!

I've been thinking about this one for a while, and finally built up the courage to do it.  Ana had lots of good plans and I learned so much from her other table plans, but the brag post: http://ana-white.com/2012/03/simple-square-cedar-outdoor-dining-table is the one that ultimately pushed me over the edge to start.  I spent a ton of time researching wood types, Minwax types, Kreg Jig settings, etc.  Finally pulled the trigger and got started.  It took me several weeks start to finish, but it was usually only a few hours at a time at night after everyone had gone to bed.  The most labor-intensive part was triple-coating all of the redwood.  Coat, dry, flip, coat, dry, sand, repeat.  Took a loooong time but the finish is absolutely gorgeous.  The photos don't really show how deep red the wood really is.  Actually assembling the table didn't take that long.  Big thanks to Finns-Dad (user) for the inspiration and good photos - it was relatively easy to build my own plans in Illustrator from those.  Now to make some matching benches...

This was my first project after discovering the "Ana White" web site.  After looking through the brag photos I zeroed in the Rustic X Console.  I was specifically inspired by the photos from "Celeste808" and "aDIYguy".  It also gave me an opportunity to try out my new Kreg Pocket jig. I hope you like the pictures.

I took Ana's amazing easy upholstered bench from modern to "magnifique," with a simple pleated skirt and silk upholstered seat cushion! Now our oddly shaped breakfast nook has a built-in that doesn't look so--well--built-in! Ana was right, it truly doesn't get EASIER than this :o)

My husband tackled the Fancy Farmhouse Table and finished it in 1 weekend and it looks amazing! I could not be more thrilled with the outcome.

My wife was needing some extra storage in the garage for seasonal decor totes.

So, of course, I first go to Ana White's website. Voila, I found the perfect plans for the space I had to work with.

- The final product ended up being 72"Hx54"Lx21"W

- I used a counter sink bit to pre-drill screw holes so the heads would be slightly below the surface of the boards. This way the totes would not get caught on or damaged by the screws.

We took the general plan of the Cassidy wood shim bed but added some features of our own. Since my husband is in the military we knew we would be moving more than the average builder so we made the bed to be more durable for frequent disassemblies. Instead of screwing the frame to the head and foot board we used carriage bolts to secure the pieces.

We also wanted to add a reclaimed aspect to our bedroom. We bought some reclaim cedar siding from a local estate investor and decided to do a chevron pattern. After staining the whole frame, we applied the siding to both the head and the foot board since we bought basic plywood and wanted to cover both ends. Plus, we liked the look with both ends done better. We cut the siding at 45 degree angles and then custom cut each piece to fit. This was a time consuming area since, with reclaimed wood especially, each piece is unique. We then just used liquid nails to secure the pieces.

To finish we assembled the bed and applied a paste wax.

I had this wine refridgerator that my wife gave to me years ago for a birthday and it really needed a home since it's been sitting in the corner of our dining room for several years.  After seeing some of the adaptations of the Printer Cabinet, I decided to try to modify if for my use.  I put pencil to paper and came up with a two sided design that would hold the refridgerator and all of our wine/bar glasses as well as some liquor.  It came out much better than I expected since this was my first real go at making any kind of cabinetry.  Measure twice, cut once really works.  I am eager to start my next project.  Thanks for the inspiration!

Saw this clever side table on Pinterest. It's made out of 1 1x8x8. I was able to figure out how to build a jig for the table saw to suit the project and then it was easy peasy lemon squeezy from there.