Community Brag Posts

I built this headboard to coordinate with the nightstand, tv console and blanket ladder I had previously built. We recently purchased a King size bed and found ourselves in desparate need of a furniture makeover. I modified the plans to fit our bed, and wanted a beefier look so I used a combination of twelve 1x6s and three 1x4s as opposed to only using 1x4s for the panel back. I also used 1x6s for the trim as well. Legs were made of 1x4s, doubled up at the bottom for additional support. I built it so that the legs could bolt to the bedframe using lag bolts. I also wanted it to be a bit taller so I increased the height to 56" tall.

Modified the Camp Loft bed with Stairs plans slightly so that the dresser would fit under the bed without banging your head for access.  The heght is taller creating the need for railings to be added to the platform.  Conversion to bunk beds was considered so all bottom boards save the front rail were installed.  If bunk beds are needed, just add the 2x6 front rail.  The mortise slot is already cut.  Went with mortise and tenon joints instead of pocket screws.  Cubby storage area created under the platform accessed from left side.

My kids are very into the "Magic Treehouse" books so my version of the Sweet Pea Bunk Beds is called The Treehouse Bunk Beds!
I made a few modifications, mostly for ease of access and airflow. I added windows for each bunk on the non-stair side of the bed because my kids room tends to be really hot so I thought they would appreciate more cross ventilation.
I made the side panel on the upper bunk removable (so that I would have access to put the fitted sheet on that end) by using pocket hole screws to hold the boards together, which make it one solid panel then I put 1x2s behind where the panel would go so it wouldn't fall in and used 4 slide bolts to hold it in place so it wont fall out. Also I made the two front panels on the lower bunk hinged doors so I could just lean in to change the sheets. The method for these was basically identical to what I described above but I attached them with non-mortised hinges.
I'd love to get the storage boxes made on of these days. Maybe after they start kindergarten!

I used 2x4’s to make these bar stools and used Valspar weathered gray stain. I found the plans online by searching “chunky barstool”. It cost me around $85 to make all 4 of them.

It seemed as though this project started out as a nightmare. I didn't think it was going to happen. Working with 2x2 and soft doug fir is no fun. I bought a kreg jig and was super siked to use it but really couldn't figure it out yet so I just pre drilled and blasted screws in from the sides. Luckily I took some time to wood fill and do clean up work and you have no clue. I am so proud and excited about how this came out. It brought tears to my wife's eyes and maybe even a little to mine. Added some dipped blue legs and a simple blue band molding to pop off some color. Went to babies r us and purchased some canvas cubes and crazily enough the blue matched exactly!!! That was not planned.
All in all this will be in use for years to come.

I built this table in the summer of 2017 specifically for our new home.  I used the reclaimed barnwood from my wife's grandfather's corn crib barn he built in 1947 along with a few pieces of lumber cut from trees that were blown down during hurricane Katrina.  The table top boards were planed to 1" thick and glued on edge with biscuits.  The table top is wrapped by a ripped rafter from the barn about 2" x 2".  The verticals of the legs are laminated leftover pieces, one of which has the initials of a son preserved from the original barn.  The horizontals of the legs are from pine and red oak Katrina wood.  The table bracing is made from barn rafter material and the metal straps are made from scrap and painted black.  The table itself has no stain, because we felt the true charm would be more appreciated showing the old nail holes, knots, and bug scarring.  It is finished with three coats of clear matte polycrylic.  I engineered the table into two pieces, so that the top could be removed for ease of transport. 

You may see our table in HGTV's Home Town Season 2 Episode 3 originally airing January 22, 2018 at 8 CST.

For my second project I wanted to build something a little more difficult than a shelf.  The hubby showed me how to use our power tools and I was unstoppable.  I chose this great bench because it fit the feel of our house and I wanted an entryway spot to sit while putting on shoes. 
The finishing took much longer than it actually took to build the bench.  I thought it would be more difficult to get the precise angle measurements  to make the supports under the bench, but it was not bad at all.  I can 't believe I built this pretty bench!  I have the building fever now!

I've been thinking about this one for a while, and finally built up the courage to do it.  Ana had lots of good plans and I learned so much from her other table plans, but the brag post: http://ana-white.com/2012/03/simple-square-cedar-outdoor-dining-table is the one that ultimately pushed me over the edge to start.  I spent a ton of time researching wood types, Minwax types, Kreg Jig settings, etc.  Finally pulled the trigger and got started.  It took me several weeks start to finish, but it was usually only a few hours at a time at night after everyone had gone to bed.  The most labor-intensive part was triple-coating all of the redwood.  Coat, dry, flip, coat, dry, sand, repeat.  Took a loooong time but the finish is absolutely gorgeous.  The photos don't really show how deep red the wood really is.  Actually assembling the table didn't take that long.  Big thanks to Finns-Dad (user) for the inspiration and good photos - it was relatively easy to build my own plans in Illustrator from those.  Now to make some matching benches...

This was my first project after discovering the "Ana White" web site.  After looking through the brag photos I zeroed in the Rustic X Console.  I was specifically inspired by the photos from "Celeste808" and "aDIYguy".  It also gave me an opportunity to try out my new Kreg Pocket jig. I hope you like the pictures.

I took Ana's amazing easy upholstered bench from modern to "magnifique," with a simple pleated skirt and silk upholstered seat cushion! Now our oddly shaped breakfast nook has a built-in that doesn't look so--well--built-in! Ana was right, it truly doesn't get EASIER than this :o)

My husband tackled the Fancy Farmhouse Table and finished it in 1 weekend and it looks amazing! I could not be more thrilled with the outcome.

My wife was needing some extra storage in the garage for seasonal decor totes.

So, of course, I first go to Ana White's website. Voila, I found the perfect plans for the space I had to work with.

- The final product ended up being 72"Hx54"Lx21"W

- I used a counter sink bit to pre-drill screw holes so the heads would be slightly below the surface of the boards. This way the totes would not get caught on or damaged by the screws.