Community Brag Posts

Fun project 

Made the double bench from DIY Pete. Curved top slats for the back rest for a little more style.

For my niece's birthday, we used Rayan's plans (over at the Design Confidential) to build an industrial folding chalkboard sign. I used 1/4" MDF for the chalkboards for smoothness and 1x2 pine for the frame, stained one coat of ebony & one coat of rustoleum "sunbleached" stain. I totally forgot to take pictures before we dropped it off, but it was super easy and a real hit!

Inspired by the Fancy X farmtable plans. Added a crossbeam mid legs. Stained top and center beam chalk painted legs. Bench inspired by the table just minus the diagonal pieces.

After searching for months for a coffee table I found one and put my DH to work. This is his first time making any type of furniture and I think he did an awesome job. We used Red Oak for the table and it weighs a ton :)

This plan was spot on but i do suggest when sinking the pocket screws to secure the table tank it slow and do not over sink them they will protrude from the table top. This was fun to build.

I loved this plan.  It was my first build from Ana White plans and a true jumping off point for my imagination.  I used pine boards, matte red underneath and semi-gloss white top coat.  Steel wool was my tool for the distressing.

Thanks Ana! Appreciate all the plans and how much I’m learning.

This was our first build, so it was definitely a learning process! We followed the plans pretty closely, with a few minor modifications to suit our needs. The finish was inspired by CreativePineapple's stain/white paint combo - we loved it so much that we had to do our own version!

The center console section was built out of 3/4" MDF - we knew we were going to paint, as opposed to stain, and it was quite a bit cheaper. We primed and painted this section as we went, as we knew that getting our hands/brushes into the cubbies after assembly would be difficult. This added to the time to finish, but it did make for an easier (and probably more even) paint job.

The side panels and back (not shown - we still need to do cutouts for cords before we attach) are 1/4" plywood. The legs are untreated SPF 4x4s, and were definitely where we ran into the most problems. Finidng untreated 4x4's was difficult enough, and when we finally found one that didn't have a ton of chunks and dings in it, we had problems with wood cracking when we got it home. We waited until the wood had acclimatized to our home and stopped cracking, wood-filled the cracks where we could and tried to position the legs so the cracks were facing the console, and hidden. Luckily, this approach was successful, and you can't tell that cracking was an issue. In retrospect, I probably should have just gone with cedar, particularly since we weren't staining it and it wouldn't have mattered that it was different from our other pine boards.

The only placed where we really differed from the plans was adding additional trim to the front section, as opposed to edge binding. The trim was simple 1x2s, similar to the bottom trim.

We primed and painted the entire white bottom section before attaching the top, which was made of stud-grade spruce 2x4's. We used a wood conditioner on the spruce before staining, as it is such a soft wood. The stain was left on for 15-20 minutes before wiping, as we knew we wanted a darker, richer colour. Two coats were required to get the shade we wanted (3 on one board which wasn't soaking up the stain as well). We then finished with 3 coats of Varathane Diamond Wood Finish, to get an especially glossy finish.

We were blessed with a LARGE TV for Christmas. Totally unexpected. So I needed to build a table for it to sit on. I previously made a narrow farmhouse table and liked the look of it. So I decided to make a smaller version with two shelves underneath. To reduce clutter, I built a couple of "towers" for the x-box, dvd, and wii to sit on (2 half boxes with 1x4 sides with 1x4's nailed across the top.) Dimensions of table are 48 inches long x 22 inches wide x 32 inches tall. (TV is a 60 inch and I think it fits great!) I used pocket holes and 1.25 inch pocket hole screws to attach everything-except I nailed the shelves down to the supports using 1 1/4 inch finishing nails and used 1.25 wood screws to attach legs to apron and supports to legs. I ripped the 1x4's down to 3 inches on the leg front and 2.75 on the sides to make them uniform. Also the aprons I ripped down to 3 inches wide. The shelf supports are about 1.5 inches wide and the shelves themselves are about 18.5 inches wide.

I forgot to add the height of the shelf when I measured for the placement of the two by two shelf supports, but it still turned out well. 

Outdoor couch is a delight.

Damian

My wood scraps were definitely getting out of control, and I needed something to store the wood vertically. I had some spare wood (free from Craigslist), so I put together a wood storage bin. All in all, the project cost me the price of some Kreg screws.

This project could take alot less time if I had a wood planer.  I use a belt sander to sand all pallet wood and this is what takes the longest. Well applying the polyurethane takes a while to finally get it to the way I like it. Bc I'm my worst critic. 

6 seater Recycled Fijian Kauri with extra leg supports, one side higher & closer for kids.

Marty