Community Brag Posts

Awesome desk made from the Channing Desk plans on Ana-White.com! I had such a great time building this desk with my girlfriend. It was our first of many builds together.

thanks again ana-white.com

I adjusted the depth of the bench to accomodate a bath vanity top with sink (from the Habitat reStore). The width was adjusted to allow for 2 feet of workspace to the left of the sink. The overall height was adjusted to my wife's height. The front legs were made longer than the rear to account for the slope of the yard location.

Thank you very much for this marvelous plan and idea. I built one for each family of grandchildren and love the finger-saving torsion hinges and front lid relief. I did end up trying biscuit joints (except for where the 1x2 boards join to the legs) as it left the inside of the box looking cleaner, especially if stained instead of painted.

Your beautiful Fancy X farmhouse table. We wanted to seat 8. Used your plan with the top idea from Hint of Home. We used cedar tongue and groove for the top. We are so pleased with it! Now for chairs!

My mom asked me to build her a buffet to match the Provence style dining table I built her a few months ago. I used the Providence Table plan as a jumping off point. Here’s a quick breakdown of the changes I made to the plan:
• Supply list – 3 2x6x12′ boards for the top
2 2x6x10′ boards for the shelf
5 2x4x8 boards for the legs and supports
• Design – I cut the legs to the same dimension, but flipped the legs 90 degrees so the profile matched the table’s. I placed the leg support 4″ from the ground, again to match the dining table. I added a shelf by drilling the 10′ 2×6′s down onto the leg supports, and used scrap 2×4′s under the center to keep it from dipping. I nixed the center top support, and decided to keep the cross supports at the same angles and length, but doubled them and used scrap 2×4 cut at 18″ wide (the width of the buffet) to span the three boards so the center wouldn’t dip or warp over time.

We chose cedar to match the table and cut down on chemicals, but it could cost a lot less if you used untreated pine for indoor use. Either way, $120 for a twelve foot long buffet isn't too shabby!

I built this for a silent auction at my school. My students chose the theme. Each of the kids in my class signed the white legs. Super easy to put together after following the plans to cut each piece of lumber. The painting was another story thanks to those stars!

Matching beds

We just slightly modified the plan to accommodate our really great industrial sewing table base.

Faux fireplace.

We love the medicine cabinets that are found in 5 star hotels and had come across a blog (Batchelor's Way) that had built one very similar. We decided during our renovation that we wanted one, too. In the photo you can see that we still have to install the light fixture, which fits perfectly within the high top molding, and the vessel sink and wall-mount faucet below.

This was my first attempt at building something with doors- the one on the right got knocked off square at some point and required some finagling to get it to fit. As a result, there's a gap above it, but it opens and closes smoothly. I'm okay with it. It's not perfect, but at least it's MY not perfect.

Inspired by a photo on a DIY site i made this simple stool from pallet wood. No plan, just an idea, and i know that the hight should be around 20".

Build this bench for our dining room. Had some left over stuff and got a 11 feet plank for free at the lumber yard.
66 inches long, 14 inches wide and I made it a little higher, 19,5 inches.
Have a weakness for red benches :-)

Very easy build! This took just a few hours to complete and gave us some much needed flare for out tiny guest bathroom! 

I am going to be a first time Grandma and this project has been on my mind to make for him as soon as I saw it!!!
Assembly was a little tricky as I felt I needed to be sure it was very sturdy and safe. I also felt a bit out of practice as I haven't been making stuff as much as I was in the past, it may be more of a beginner level project, but I definitely needed my dad's guidance and assistance. (Thanks dad!)
I felt it needed a thicker wood for the body of the scooter so I used 1.5" wood instead of 3/4".
I am unsure on the time to make as I worked on it in the evenings after work. It did take more time than I expected, but I am super picky and wanted to add some extra touches to it.
I found the perfect monkey and bodysuit with scooters on it and that made it the perfect baby shower gift!

My son is a big Mario nut. And when it came down thinking about a new bed for him we sat down online and started searching for ideas. When we found this bed we both loved it right away. And when i found it was made from plans on Ana- white i was so excited as i have made a few projects already. My son was so happy the whole time this was being made. He was going to have his own castle. Once we finished the build he decided that he had to have a door so i made some curtains and embroidered Mario characters on each one. I let him decorate the inside with Mario stickers and he loves being able to have a Mario level right where he sleeps.

This was my first prject of this scale. First time making doors and drawers. Took about 3 months of working after work and weekends to finish. I'm pretty happy for how it trurned out as new wood worker. Time for a drink.