Community Brag Posts

I made 4 Simple Lounge chairs and 3 Ottoman/Accent tables. They are made out of 1x3 and 1x2 furring strips. I was worried about how sturdy they were going to be but, in the end they turned out PERFECT!! We absolutely LOVE our new set!

I built this for a friend of a friend. They had seen a similar hall tree on line that ran between $300-$500. It was made of a mix of materials, including mdf and veneer. It was for newlyweds so I did the finishing (something I really hate) and I made the cushion. I had the mirror cut at a local glass shop, and had it cut a bit shorter than how it appeared in the picture they gave me - I was afraid someone would toss somthing onto the cushion and it would end up hitting the mirror.
They seemed happy with it. I hope to get a picture of it in place so that I can add it to my album titled "Look what Gramma made when she could still do things".

This is my first project! My friend and i were debating what to gift our friends for their anniversary. This was perfect. Good first time beginner project. 

I enjoyed making this project! My wife loves the table and benches.

We made this for my daughter's bedroom. There was not enough room for a canopy, so we adapted it a bit.

This table is SOOO great, and I get tons of compliments on it. It was easy to build as well.

I did have a problem, in that I made it to use outside and outdoor tables are shorter than indoor tables, depending on the chairs you use. I had to cut apart the legs after I had them built, which was a pain, but was completely my fault. 

For an outdoor table, make your leg uprights 18-1/2" - all other leg cuts are the same.
I made mine 17-1/2" and used 2x4 material for the feet (my 1x4's kept splitting). You will also need to adjust the length of the center angle pieces, which I laid out after the legs were assembled and the horizontal supports were attached.

You can see from the photos that the unfinished legs are according to the original plan. Once the center was cut down to the new length, the angled pieces make more of a true X.

I also flipped the base upside down to attach the top. I used 2 1x1 'stringers' cut at the same angle as the top of the legs, centered the base on the under side of the top, and screwed through the stringers to the top 2x10s. I used nickels to space the top planks for drainage. I then screwed the stringers to the side legs from the side. You won't even see them unless you're sitting on the patio - standing or sitting in a chair, you don't notice them. But then there are no screws showing, nothing to patch, and it's sturdy to pick up and move.

Built this for our dining room. Added two feet to the length. Neighbors started talking and now I've been commisioned to build a table and bench!

My wife has always been a huge fan of Ana White's website, and we've wanted to start making some of the projects now that our children are a bit older (5 yrs., 3yrs., 5 mos.). Plus, after finishing my Ph.D., I've finally found the time to begin woodworking as a hobby--and I love it!!!

This was our first project together. I did the building, and my wife completed the painting. The kids love the table, which we use as a breakfast and snack table for them.

Ana's plan was wonderfully simple and clear, and the materials were inexpensive and purchased at our local small town lumber store.

My only suggestion for others interested in building this project to be a food table is to consider using a solid piece of wood for the tabletop and perhaps the same for the chairs. We are constantly cleaning food gunk out of the seams between the joined tabletop planks. I imagine that this will require a bit more work for the chairs, but with little kids who make horrible messes with their food.

Blessings,
JB

I made this chair in pine based on the plan for the Bristol outdoor lounge chair. But I changed the dimensions to fit my pillow (21"x21") and I raised the seat (increased the length of the legs by 3.5"). I modified the armrests so that they don't cover up the pillow since I didn't want to lose 7" from the seat. I plan to use this indoors at our mountain cottage. It still needs to be sanded and stained, but I'm pretty pleased with the result. I may have to make a matching ottoman next.

This was a great project. Added diffrent door design which resulted to great outcome.

This was a fun project that ended up being a multi-use table! This was originally built as a small island for the kitchen but as the family grew it became a changing table! The top was purchased online at home depot, the base is made of douglas fir 2x4's and the corners accents are Simpson Strong-Tie ZMAX Galvanized 16-Gauge 2X Rigid Tie Connector available at HD for about $2 each. Thanks for looking! See more at my website analogwoodworks.com!

After the success of my first project, I had to go for #2. I loved not having to predrill and countersink anything on this...just pound away with my hammer. Since I had a bit more confidence about building, I was also able to move a lot faster on this project. I modified the plans by not adding a drawer and keeping the bottom a shelf, as well as adding smaller doors and maintaining an open shelf above them.

I made this bench for the daughter of a friend to be used as the guest book for her wedding after seeing this brag post - http://ana-white.com/2013/07/wedding-guest-book-bench-modified-fancy-x-….

I made similar modifications, including the use of a project panel for the top. I made a couple of other changes. I added two reinforcements under the top. And instead of using a 2 x 4 for the legs, I glued up two 2 x 2s.

I also matched the font of the wedding invitation for the bride and groom's names and wedding date.

While the total time spent building was somewhere between three and six hours, it was built over a couple of weeks.

Modified Anna White planked sideboard plan.  Made the unit smaller and changed the center cabinet to a wine rack.  This is my very first piece of furniture. It's not perfect, but I love how it turned out.  Routed the edge of the top to add detail and used a tablesaw to square edges of 2x4's for a sharper look.  Fits nicely under my husband's antique mirror.

Modified farmhouse table - A little over 5 feet. Really a fun project

This was a fairly easy project that I believe had great results. The finish time includes a few nights of polyurethane and sanding to finish.

The fairly costly price is from wanting to make this chair like a real finished project. The bulk of the chair is made from poplar and the seat is made from a pine project board.

Our new home has a 21'x17' screened in porch that needed somthing, anything to occupy it! We looked for sectionals from online retailors and could not believe how much money they were demanding for them. Being new homeowners we could not afford/justify spending that amount. I found Ana-white.com while looking for shoe bench plans and found these 2 plans for the sectional. It was time to justify all of my tool purchases! lol

I took the 2 plans for the sofa and armless sectional and increased the size on the armless sectional by 1 seat to fill the area better. Future plans also include a bar, serving area and coffee table in the space. I bought (30) acq 2x4x8's and, not including scrap pieces, had 3 reamaining full pieces after completing the project. Total for the wood materials was $130 and I also had to buy a Kreig Jig ($37) and 2-1/2" ext deck screws so all in all about $180 for the materials

For the cushons I searched local retailors and found since we were going into the winter season a lot of local stores were selling off their patio supplies at big discounts. I found a local Home Depot selling Hampton Bay deep cushions for 75% off (normally $49.98 on sale for $13.xx). I needed 8 seats and since one was a corner I ordered 9 sets (9 backs, 8 seats).

Project took me less than 5 hours pick up the wood, set up on-site shop, make all the cuts and assemble. That 5 hour timeline also included a break for dinner. The sofa sections are heavy when put together, if you plan on moving them more than once or twice a year I'd suggest putting some caster wheels on the base with locks to keep it from rolling away when being used.