Granddaughter’s chicken coop
![](/sites/default/files/D6F3CB17-2B02-4B59-AE1C-EACC5B242149.jpeg)
Made it four feet longer for her four chicks. Will be adding automatic feeders and water soon.
Made it four feet longer for her four chicks. Will be adding automatic feeders and water soon.
I apologize for not having before and after shots from the same perspective, but this is the bookcase I built to replace the very poorly sized and very poor quality bookcase that was in this room before. The room has a slanted ceiling that goes from 8' to 16,' and has baseboard heaters that got in the way of cabinetry. I worked around it. These were my first cabinets, and they didn't come out exactly has I had envisioned, but they're pretty darn close! The shelves are all on brackets that are screwed into studs in the wall, and the boards that make the sides of the bookcase aren't even screwed down. I wanted something that would be sturdy and yet easy to take down or change. I left space in the middle because we'd like to put in a fireplace one day...
MelissaLeigh144
We built the Farmhouse Table using the updated pocket hole plans. We adjusted the size and left off the stretcher board since ours is much smaller than the plans call for.
In reply to Stain Color by JLU5003
Fri, 09/12/2014 - 13:42
Thanks! I'm glad you like it. I used a layered approach with a couple of different colors. For the finish we purchased Minwax Pre-Stain Wood Conditioner, Minwax Special Walnut Stain, Minwax Weathered Oak Stain and Polycrylic. Here is a link to the blog post I wrote about staining the table: http://69.195.124.114/~theanch5/2014/05/14/diy-farmhouse-dining-table/
This was my first project, and it took me about 2 weeks to complete it. I don't have a lot of tools, so there were many frequent little trips to Home Depot (by now I think I definitely have the basics down). I would put in an hour here and there, and was finally able to paint the beautiful thing today. I am extremely happy with how it turned out. Thank you Ana for the wonderful plans. My family and I are looking forward to many evenings on the patio on the new sofa.
Built Cup storage shelf after adding a new set up cabinets and wood countertop.
I built this sturdy work bench to complete further projects off the ground! It's helped me to be organized, keep my tools together and stretch these legs!
This project is excellent for a first time builder. Mistakes don't matter much, it's pretty straight forward and easy, doesn't require special cuts. Allows you to practice measuring, cutting, drilling, etc.
I loved the RH-inspired Balustrade Coffee Table that I built for my parents, I decided to make one for our living room! Ours had to be more of a square though, to fit our space more appropriately, so I modified the dimensions. This affected our shopping and cut lists, of course. Check out the blog post for more info.
I needed to build a loft bed for a small room that has a nine foot ceiling, I wanted to have ample storage room below, but was concerned about a ladder that would stick out at an angle taking up a little too much precious real estate in the small room. Using Ana's great Sketch Up plans, I modified the design by incorporating a fifth leg as a permant addition to attach the ladder to. Part of the appeal of Ana's design was the ability to take apart the bed if it ever needed to be taken out of the room it is installed in, and the ladder became a part of the foot board end, perhaps a little unwieldy, but still able for two people to lift and move.
As a self-taught woodworker, I wanted something a little nicer than standard pine boards, and since we have a nice local hardwood supplier in our town, I was able to buy some nice red oak in a 13/16" thickness. This project gave me the opportunity to use the planer that I bought some time ago but hadn't really used very much, so I ended up milling all of the wood to bring all to a uniform thickness. In gluing up the legs, I used a spreader and a lot of clamps so that there are no screws, staples or nails joining the boards, just a lot of Titebond II.
For the ladder itself, I cut dados in the upright edges of the ladder and attached the treads with 2" wood screws along with a liberal amount of glue. I had a slight miscaculation on the width of the ladder, so in order for it to fit in between the two legs, I had to plane away a small amount of wood, which you can see the end of in the last picture, the close up of the ladder.
After a fair amount of sanding and a round over bit in my palm router to break all the exposed edges, I finished with three coats of polyurethene. The bed was assembled in the room using 2" wood screws which I had pre-drilled when I dry-fitted the bed out on my driveway. There are three screws in each corner of the mattress board and two screws in each corner of the railing. The short section of the front rail is also attached with screws so it can be removed as well if the bed is ever moved. I finished the installation with three, six inch lag bolts, two higher up going into wall studs, one near the bottom bolting into the wall plate on the floor. The bed was very solid, but has been made even more so with the addition of a bookshelf spanning the width of the footboard, and it is as deep as the ladder is wide. I offset the side of the bookshelf on the ladder side to allow for a two inch gap so your toes can overhand the ladder treads when climbing up or down.
Kinda new at working with wood but I enjoyed this one and did it in under a day. I also just recently built a complete wooden fence before I did this so building frames was fun.
Designed by myself. Used a jigsaw, nail gun, and made miter cuts on the molding for the first time on this project. Glued a curtain panel I bought at target to the back before attaching it.
Overall size is 7 feet tall, 3 feet wide, and 1 foot deep.
With thanks to others that had posted before me. I took my inspiration from all the Castle beds I could find and customized this Castle Bed for my Granddaughters room. We made the bottom bed full size and the top twin size. She has a closet on the inside and two bedside tables. The slide lifts for additional storage. We made a cloud ceiling filled with a moon and stars that all glow in the dark. I used 3 18' rope lights that operate By remote control. Since I did not have enough space to add the stairs in the room I built the bed, I made the arched window on the right side to be used as a ladder. The steps are next. This took 8 months, 10 sheets of plywood and ultralight MDF. a few hundred board feet of pine, 5 gallons of paint and primer, 350 biscuits. About 1,500 Grandma and Grandpa hours of pure love.
Thanks again for everyone's inspiration.
No plans I measured as I went.
Mon, 05/26/2014 - 20:12
Absolutely beautiful right down to every little detail! What a lucky little girl to not only have that amazing bed but to have such devoted loving grandparents! You really can see how much love went into every bit of that build!
Mon, 05/26/2014 - 22:00
Thanks for sharing, it's wonderful! What a lucky little princess!
This was our very first project! It went amazing ❤️ I absolutely love it. The plans provided were exactly what I needed and broke down everything for a first timer. Thank you so much Ana!
This was my very first project to take on with Ana's plans. My boyfriend and I helped each other, and I think the result is pretty amazing. A lot of people has complimented our project, so we will be building something else soon.
I assembled these two benches over the 2014 Memorial Day weekend.
Thanks for the plans! My wife and cat love that cart, and I'm not sure who will win )))
This is my first build from Anna's plans.
I used 5 5/8 fence pickets I had in the scrap box to give the chairs a wider arm rest. I wanted something wide enough to safely hold a paper plate and drinks.
I planned them, routered the edges and put a coat of oil based polyurethane on them.
The table is just something I put together and the top is a 1.5 inch thick 16x16 concrete paver.
If you like the wide arms, use wood glue and clamps, not nails or screws. Saves you from having to fill them and it looks better too.
Enjoy
And thank you Anna for a great build!
My version of the 8’ Grandy Barn Door Console. I made it deeper to accommodate a sink that we haven’t put in yet. It was so fun building again. I haven’t built a piece of furniture since high school. Thank you for your amazing plans!
I completely made all of my my teen daughters bedroom furniture from plans from Ana-White.com.
Farmhouse Bed
Open File Cabinet with desk top for dressing table
Open File Cabinet for side tables.