Community Brag Posts

I chose to cut the back supports at 15 degrees to allow a little bit of a slant in the chair. I love it. Every flaw is perfect. 

This was a week-long project. I love this site because there are so many original tables to get great ideas from! I chose the Farmhouse table plans because of its simplicity and beautiful lines. The length of the table was a little much for my room, so I shortened it a touch. Dark walnut for the stain and Satin Ultra Pure white for the legs to match the trim in my house... a real beauty! Have fun with yours!!!

My kids we're spending the summer at their Dad's, so I wanted to surprise them by redoing their room. I've never built anything before, but I've found that I really love it!

I decided to take the advice of another builder and reduce the width by 1/2 in in order to get 2 toy boxes out of one 4x8 sheet of plywood. I also added a lid.

I tried to replicate a driftwood type paint finish by making a stain out of steel wool, and apple cider vinegar. After it was dry, I did a paint wash with a charcoal colored paint, then added a bit of cream paint to lighten it a bit, and dry brushed it on, I did this one more time making it even lighter, then wiped and blended. After the piece was dry, I waxed it using a dark wax made from Howards was paste and Minwax jacobean stain.

The inside is ombre painted too!

I really love the way they turned out!

I've needed a console table for under the stairs but everything I've looked at has always been too long. l took the plans for the Rustic X Console table and modified them to fit the space perfectly. I love the look that I was able to get by adding the 1x2 Xs to the top.

My husband built this planter in just a few hours. He said it was pretty simple, and the plans were easy to follow.

I was excited to make these for my 2 nieces.  It was new for me to cut at degree angles but it came together well.  I did them over time but I'd estimate about 2.5 hours for each scooter (I'm a newbie). I ended up putting a 5th wheel in the front to stabilize it more.  Since it's a gift I thought better to be on the safe side.  Casters were much cheaper on amazon than at Home Depot.  

Thanks for the plans Ana! 

My family has been in need of a new place to sit and have dinner. As a homeowner with little experience in making furniture I decided "I can build one of the tables on Ana's website." I never thought I would learn as much in the long process. I watched Patrick Hosey's video on the Farmhouse table close to 15x to learn tips and tricks. Made a plan. Then went to Lowes to execute my plan. Got home, realized I needed more material than I originally thought and went back to Lowes. Unfortunately, that step happened more than I would like to report.

First lesson learned for me pine is a difficult wood to make perfect. Some of you might have had luck with using pine but in my hands it was very difficult. I had a hard time sanding with my Dewalt palm sander and not making the dreaded squiggles or curly q's. I, of course, didn't see them until after the first coat of gel stain was on. So I had to sand the table back down to the starting point.

Second lesson learned for me was do not get ahead of yourself when applying the lacquer. I used a Deft Premium Gloss spray for my lacquer. I used Mineral Spirits to clean off any dust on the surface from lightly sanding . However, I made the mistake of putting on a second coat when I thought the mineral spirits were dry. This led to cracking and bubbling of the lacquer and a lot of swearing/drinking. I had to sand, very carefully, back down to the first layer and then start over.

Third lesson I learned was overall I love making furniture no matter how frustrated I can get at points in making it. There is something very fulfilling knowing that my family will now sit around something and share fun special meals and experiences over my table.

Please let me know how you think I did and feel free to offer tips and tricks for working with Pine. Thank you Ana and Patrick for the inspiration!

Bryan

My wife and I decided to renovate our office and turn it into our homeschool room. Built a farmhouse table for the kids (4) to use instead of individual desk along with a cubby bookshelf to use for storage. I love the way it turned out and so does the wife.

Super easy project. Was able to have it in my house in 3 days. I used a LED RGB light strip inside to be able to light it up. It came with a remote control which is very handy. I drilled a small hole near the bottom for the IR sensor to stick into. I modified the plans only slightly to be able to make a attachement point for the light strip.

This is my second project from plans on the site. My first build was in taking the rustic x table and modifying it coffee table size. After having success with that I decided to build the dining table. It took me a bit of time, mainly because I hate sanding and finishing. The 1x6's on the top were a bit uneven, so I took a hand plane to the seams. This didn't completely sand out, but it gave the top an older worn look that I really like. I did not add the iron pipe. I had a hard time finding any of the decorative embellishments for the ends and I also decided that being 6'2", I might enjoy the extra leg room.

I built both benches according to plan, except that I increase the outside 2x2s of the top to 2x3s and made an upholstered bench to serve as a cushion. I liked the look of the wood top for the benches, but wanted something a little bit more comfy.

I would strongly encourage anyone to build items from any of these plans. I've always been good at building, but just needed something to serve as a guide. There are times when your own modifications come in to play. I think that reflects you taste and in some cases the material you have available to you. But all in all, everything I've tried has worked well.

I used the Counter Height Garden Boxes 2 feet x 4 feet plan (http://ana-white.com/2012/11/plans/counter-height-garden-boxes-2-feet-x…) but decided to make the sides 12 inches high versus the 8 inch in the plan.

I decided to use two layers of weed control cloth on the bottom which I used a staple gun to attach. I then used 7 evenly spaced 1x4's for support. I then layered old newspaper on top of the weed control fabric. Filled the planter with 2 large bags of Garden Soil from Home Depot, and finally put down a 2-3 inch layer of mulch to help with moisture control as I am in Florida and the sun dries plants out quickly. I do plan on running a timed drip line irrigation to the planter this winter.

Since Cedar is very hard to find here, I opted for pressure treated wood. For those concerned about using pressure treated wood in gardens I offer this for you to read (http://www.thesurvivalistblog.net/is-treated-lumber-safe-for-building-r…).

When all else was done I planted Basil, and 2 types of Tomatoes (Roma & Cherry). The planter has been such a success I am planning to build several more this winter.

Made the table 6 feet long to better fit the space. Made it 2 years ago, just now getting around to post it, but it has held up well in our vacation rental.

My wife came to me with a ad for a table and told me it would look great in our kitchen. I agreed it would except we can't spend 900+ on a table. Then I offered to build her a table without EVER having done this before.

Though this website I came across the easy to follow Farmhouse Table plans that for me took a lot of the guesswork out of this project. The material list that comes with every plan here was a huge help. In the end I think we ended up with a great table that will last for years to come.

There is a great feeling of accomplishment sitting down at a table you built with your own two hands. My wife hopes this will become my new hobby as she is searching the site for project #2.

Trust me when I say if I can do it anyone can.

This is my second build of the Providence Bench...finished in Annie Sloan emperor's silk and General Finishes burnt umber glaze.  So much easier the second time around that I included a tutorial at www.ourhomemadefamily.com.

I followed Ana's plans exactly except I extended the headboard's 5 panels from 6" to 9"