Super table i like it so much. Cant wait for summer to use it outside.
Had to add leg supports for the none drawer side and added a back for the entire unit. Fun Project. 15th birthday present.
Instead of the 2X6, we used an additional cedar board to complete the sides and the ends of the planters. This was more cost effective and still provides enough support to hold the planters. This is a great alternative to the more expensive items we found online. We will be building multiple to put in an unused space in our yard. Great project!!
This is not my first project, but it is my first brag. I installed new windows in my house this fall and took out some double-pane windows. I can't yet afford to build Ana's greenhouse, so I made this. I removed the old frame around the glass and took some old 2x6 green-treat, ripped them down to 2 1/2" and made new frames around the glass. I then purchased some treated pickets to make the box. The top is slanted at 15 degrees and I put a shelf in the back for a few extra six packs. The overall size at the base is roughly 36" by 46", so I can fit 6 flats there. Since I didn't have to make sure it was really square nor did I have to sand, it was my favorite project yet. I can't wait for the snow to melt and the hard frosts to disappear.
I made this hall tree as a gift for my wife. It's a classy way to store coats out in plain sight. it is larger than the design specs from Mimi (7'H by 4'1" W) and built-in instead of free standing. Our house has a boiler with floorboard radiators. There is a radiator inside the hutch, and heat comes out of the holes just behind the lid to the bench this heats up the coats as they hang on the rack. The radiator also heats the compartment under the bench which aids in drying damp boots and other items. Fun project, also an easy project thanks to the Kreg Jig!
I built the farmhouse console table over the course of 3 weekends. A relatively easy build, the pocket hole were the most time consuming. Its made mostly of Douglas Fir, and pine for the 2x2's. It's a heavy piece, it weighs about 250 lbs - ish. But the wife loves it, as it will be going in our kitchen.
With lots of leftover wood from previous projects (farmhouse table and sideboard), I decided it was time to start another project. (I did head out to Lowes to get a piece of 4x4 for the legs...they only had Cedar. My friend found some Fir at Home Depot for a buck more).
Found the plans for the Farmhouse Bench, looked at other brag posts and their suggestions...then got to work!
Cutting the pieces was fast and relatively easy. Predrilling the pocket holes also went quick. Putting the pieces together was also very fast (though I did have to add extra pocket holes here-and-there so that the legs and two end-aprons were more sturdy).
Sanded the piece, then added a coat of Rustoleum Dark Walnut Stain, and then a couple coats of Deft Satin varnish.
First part of the outdoor entertainment build was a 6-person dining set. Learned a lot from this build, and it was a great project to build confidence and get back into woodworking. This set is a tank - heavy, durable, yet comfortable and beautiful. We look forward to many gatherings with friends and family, just quiet dinners with the two of use and the pups.
Mon, 05/31/2021 - 07:45
Great job! Love the finish. Very warm and inviting :)
Mon, 05/31/2021 - 08:51
What a great piece of the set! Love the finish choice, you've created such an inviting space!
It's the first thing I've built on my land in the Cape Breton highlands, Nova Scotia, Canada. We staked it down because it gets really windy here! Great design, thanks Ana!
I built this storage crate to fill out space on top of my kitchen table. On my table saw, I ripped 1/2in birch plywood down to 6in widths for the outside frame and 5 3/4in for the dividers. The dividers are 6in wide and so I cut the outside ends to 7in. I attached the whole thing with 1 1/2 finish nails and glue. After finishing, I attached some L-brackets on the corners and drilled 2 holes on either end for handles. For handles, I simply braided 6 strands of jute together and tied knots on the inside of the box. I have more details and photos on my blog link.
My first projec twith drawers! the metabox drawers were definetly easy to make and use and work beautifully.
I made the carcase using plywood and did 1x2 poplar for the face frame. Shaker doors are 1x3 poplar and sureply underlayment for the inserts.
cabinet doors were finished using BIN primer (2 coats with sanding) and then Benjamin Moore Advance cabinet paint in High gloss silver satin. Interiors were finished using leftover / mistints, and I still need to do some filling and sanding on the insides of the doors (I have to take them down to do a final coat but am waiting until I have finished the other set of doors)
the upper cabinet is a dish drying cupboard so I omitted the bottom plywood piece and instead used 1x3 on the front and back so the bottom would be open. then I made the shelves using 1x2 and dowel (paint the dowel first before cutting!!). This thing is a dream to do dishes in!
Used Kreg pocket screws, Kreg jig for the euro hinges (1 1/4 and 1/3" overlay), and also a kreg jig for the shelf pins. Metabox hinges for the drawers. Still trying to decide on handle hardware so I'm using painters tape at the moment.
Countertops are concrete using Rapidset mortar mix and the michael builds method (linked below).
Planters are just a small poplar shelf using leftover 1x3 with metal terra cotta pot hooks attached to the front. I lined the pots at the bottom with plastic yogourt tubs with holes in the bottom so the cutlery doesn't chip the pots. Those also drain onto the drain rack below. everything is painted the same colour although I used high gloss for the door fronts, so the shelvings behind the pots matches the wall perfectly and sort of dissappears into the walls to highlight the terracotta.
sink is a "new" vintage ceramic sink that I found on FB marketplace for 50$!!! had never been installed and didn't even have the holes bored out. unfortunately the drain holes were very deep and requied some macgyvering but luckily my husband had a great attitude about it and managed to make it work with a lot of googling for odd sized drain bins. Props to husband for doing all the plumbing on this bad boy, including moving over our RO system from the other side of the kitchen and installing a new hose bib under the sink for the other side of the house (why not?!).
I learned so much from this project! Including to store your poplar inside and on the flat surface or it will warp and your doors will not be flush. luckily it only affected one door but it is still super annoying.
thank you ana for everythign! loved the comment "Get on board with these euro hinges!" you are so right they are so forgiving!!
Fri, 08/27/2021 - 08:31
Love the integrated flower pots and the dish rack is so cool! Thank you for sharing, I can tell a lot of work went into it!
This was my very first project I tackled from Ana's site. I wanted to see if I could do it, so started with something easy. I think it turned out great and looks great in our flower bed in front of our house.
Built for my Daughter and Son-in-laws new home
Tue, 10/05/2021 - 09:19
That is very sweet and looks amazing! Thank you for sharing~
As part of my daughter's big 8th birthday bedroom re-do, I knew she needed some new storage for books and...er...stuff. You know how kids accumulate little scraps of paper, photos, tiny toys. I can't stand to see that kind of stuff lying around, so these cube bookshelves seemed like a great solution for the problem. The canvas "drawers" are from Target and were not expensive. I followed Ana's Six Cube Bookshelf plans very closely with two exceptions. First, I shortened the legs an inch to ensure that the units would be short enough to fit under the bedroom window. Second, I added an overhanging 1/4" MDF panel to the top of each bookcase and trimmed out the bottom of the panel with cove molding. The rest of the wood used was solid pine. I'm now working on building a third unit for my other daughter's room. This time I was smart enough to finish the insides of the cubes before putting the whole bookcase together. Getting into those corners once the project is complete is time consuming and difficult. Painting the insides of the boards ahead of time has proven to be much simpler.
I built this little hall tree, bench and shoe organizer for the garage entirely from scrap lumber and left over paint. Keeps us organizeed. I really like it.
My first “big” piece of furniture! I have over the last year realized I had a little sawdust in my blood! My dad is a 3rd generation carpenter, he is the youngest of 5 boys and he is now 79. I started with a couple of quilt/blanket ladders for my daughters, then graduated to a headboard. Then last Christmas I surprised my dad with an oak bookshelf (because oak is the best 😉) I knew that’s what my dad loved. It brought him to tears! So, then my daughters began showing me pictures of desks, tv chests, etc and I gained a little confidence with each piece.
I finished these last weekend and finally took pictures.
I found 44 5' cedar pickets on craigslist for $30 and built these raised beds. I built them according to Ana's instructions except I made them bigger (4'x8'). Since my boards were 5' long I couldn't span the entire length and went with a brickwork style overlap so there wasn't one seam in the center or a weird off-center seam. And, of course, I blogged about it.
Watch the video on how I did this project here: http://youtu.be/IoP2cKN2WeY
For this week's woodworking project I'm building a Rustic Cooler Box from used Pallets. The project was a lot of fun to do and pretty simple! By just using some old Pallets that were free I was able to build something that will get a lot of use. Plus, by using the Pallets I think it turned out really cool looking!
How to video http://youtu.be/IoP2cKN2WeY
Wed, 11/27/2013 - 04:02
Awesome way of doing a pallet cooler. Keeping the cost minimal your way of finishing it was really good. Personalizing such coolers would be interesting!
I made this for my daughter this year for Christmas. I’m pretty proud of how it turned out.
Wed, 12/22/2021 - 17:59
Thank you for sharing, wonderful job and a gift that will be cherished for years to come!
I made this table and chairs for my 1 year old nephew. He is still a little small for it but the table and chairs are both very sturdy. The table top is a one piece, 24 x 36 ,edge glued pine board. I used the one piece table top as an alternative to screwing the 3 boards together. I followed the plans for the table for the most part. As for the chairs, I followed the plan to build the seat base. For the legs of the chairs I took advise from carongirls' table and chair brag post and used 2x2's. I used 1x3's to stiffen the chair legs. I also lengthened the table legs and chair legs by 2 inches.
I needed a heavy duty dog bed for my puppy after he destroyed two regular dog beds. I used 4x4s, 2x4s and fire hose. He has not been able to destroy this one and he loves it.
Mon, 07/08/2013 - 15:48
I have a pit bull. Shes the sweetest thing but loves to chew up her own beds. She wont chew the shihtzus bed or the cats beds just her own. I'd like to see her try this one out.
;) Now if I could figure out a way to get my dad to give up one of his fire hoses. hehe
Great job, great idea
~Melody
Comments
Ana White Admin
Sun, 01/31/2021 - 11:28
Beautiful!
Super cool table, thanks for sharing!