Community Brag Posts
Herringbone Shiplap barn door
![](/sites/default/files/herringbone%20slat%20barn%20door%20-%20closed.jpg)
This sliding barn door was built with pre-primed shiplap 1x6s and 2x6 boards. It took a little over a day to build, sand and finish. It's definitely a sizeable piece, measuring 83x54".
![](/sites/default/files/herringbone%20slat%20barn%20door%20-%20open.jpg)
![](/sites/default/files/Slat%20Herringbone%20barn%20door%20-%20assembled.jpg)
Comments
Farmhouse Table
![](/sites/default/files/3154821693_1360184577.jpg)
My brother-and-law has been building a TON of projects from Ana's site. After comparing prices of farmhouse tables online, my husband and I decided to try building our own. I measured our dining room, modified the plans (to make the table slightly shorter and slightly wider), then we picked up some basic tools and lumber, setup a little shop in our garage, and went to work. It took us a whole week (of after-work and after-the-kids-are-down nights) plus maybe a weekend to complete this project.
We started staining the legs of the table with a minwax stain in Dark Walnut, but it left it looking very contrasty/zebra-like. An employee at the hardware store recommended Rust-o-Leum, so we finished up the top with it. Added a clear satin varnish on top (Deft), then moved it inside. We love it!!! (We stained it after distressing it, then added 5-6 coats of varnish).
Things we'd do differently:
1. Invest early in a Pocket Hole Jig (like the Kreg Jig) to piece your wood together. We actually bought one for our second wood project (which I was able to screw together pretty much the entire thing myself...whereas, both my hub and I had to work together to get this table put together...it was a pain!), and wished we had purchased this earlier.
2. Check your wood and get it as straight (not bowed) as possible. Then don't let the sprinklers or rain get on it. :) Don't worry about knots, holes, or other things that could give your table character.
3. You can stain the wood using paper towels. (I did this on the second project...worked great, and easy clean up).
4. Make sure you square up your wood every step of the way. We THOUGHT we did this...but with trying to screw pieces together, and making them fit... now we've got an extra piece of wood underneath one of our legs. :P
![](/sites/default/files/3154821695_1360184577.jpg)
![](/sites/default/files/3154821696_1360184577.jpg)
![](/sites/default/files/3154821698_1360184577.jpg)
![](/sites/default/files/3154821697_1360184577.jpg)
![](/sites/default/files/3154821700_1360184577.jpg)
Deft Clear Satin
Comments
Fri, 02/08/2013 - 09:36
Oh, my goodness!
This is a gorgeous build! The table top finish is just outstanding. You all did a marvelous job (even without the kreg jig)!
First Build: Two of them!
![](/sites/default/files/IMG_4508.jpg)
I wanted a project to build with my husband, and his desk was falling apart. Mine was old and tiny so we made two of these side by side. I did all my own work with some instruction from him, and it was pretty easy! It was also really fast: I think the total time spent was under 8 hours!
![](/sites/default/files/IMG_4609.jpg)
![](/sites/default/files/IMG_4451.jpg)
Rustic X Counsel table/ entertainment stand
![](/sites/default/files/1.6.21.1.jpeg)
Rustic X Entertainment Stand. 55” long x 36” tall. 3 shelves. Natural top with dark walnut bottom. Custom made game crates and LED back lights to finish the look.
![](/sites/default/files/34D999CD-0A99-4139-BFA4-7C8FA489C378.jpeg)
![](/sites/default/files/DB96D803-20C0-4691-AB30-B235ECFBE322.jpeg)
![](/sites/default/files/F4479B66-24B9-4869-AFF1-5F77C82245FE.jpeg)
![](/sites/default/files/90D8C51A-75DF-4331-9F2F-3EE629F7BD73.jpeg)
![](/sites/default/files/6226A8D7-99C6-4D78-82B8-00C0744FFF1B.jpeg)
Minwax Natural
Minwax 3x polyurethane
Comments
ClubHouse FORT
![](/sites/default/files/3154821843_1360364296.jpg)
My sons awesome fort. It took some time to complete, as I was doing it on my own. The balancing and juggling act when attaching a few pieces would of made some priceless videos. I used plans from " Clubhouse Bed" as a general guide.
![](/sites/default/files/3154821844_1360364296.jpg)
![](/sites/default/files/3154821851_1360364296.jpg)
![](/sites/default/files/3154821846_1360364296.jpg)
![](/sites/default/files/3154821847_1360364296.jpg)
![](/sites/default/files/3154821848_1360364296.jpg)
Comments
Fri, 02/08/2013 - 17:39
Fantastic!!
You did this all by yourself??? This is just fantastic...lucky little boy!!
In reply to Fantastic!! by Linda7
Sat, 02/09/2013 - 07:55
I did.. Thank you so much
I did.. Thank you so much
Mon, 02/11/2013 - 06:28
Wowsa!
I'm seriously impressed you did this by yourself. Not that you aren't able, but the fact that there are so many big pieces which would have been really awkward and cumbersome with just one person. Beautiful job! Love the screen name, too, definitely fits!
Mon, 02/11/2013 - 06:28
Wowsa!
I'm seriously impressed you did this by yourself. Not that you aren't able, but the fact that there are so many big pieces which would have been really awkward and cumbersome with just one person. Beautiful job! Love the screen name, too, definitely fits!
Tue, 02/12/2013 - 08:05
thank you so much.. thank
thank you so much.. thank goodness I had a toddler trampoline to help hold at times as well as a ladder that allows me to pick its height and hold the floor up for me to at least get the bottom on
Ashley Makes: Rustic X Console (Minus the X)
I built the Rustic X Console to store my growing collection of cookbooks. The plans were pretty easy to follow. I really struggled with warped boards!
You can check out my blog entry for more photos and details.
First piece!
![](/sites/default/files/IMG_20170314_181116.jpg)
Used this plan as a "practice" platform for a larger version in the future. Very simple yet nice design. I would prefer to hide some pocket holes on the sides to avoid the extra work of plugging them next time. Also, Lauan plywood panels are cost effective way of finishing the back.
Fancy Baby Doll Crib and High Chair
This is the final installment (#6) in the doll bed and high chair sets I've been building my great nieces. Each set was decorated with a lamb water-slip decal on the end of the bed (kind of a little theme going). This is the second crib I've built with dowels - I usually use 1" x 2"s - and I learned to use a spade drill bit rather than a regular drill bit. It doesn't split the wood around the holes. I've had a lot of fun building these for my nieces, and now I may have to start building them for my friends' children and grandchildren. :-)
![](/sites/default/files/3154821921_1360556073.jpg)
![](/sites/default/files/3154821922_1360556073.jpg)
![](/sites/default/files/3154821923_1360556073.jpg)
Octagon table with moulding
![](/sites/default/files/20141212_171337-1.jpg)
The angles were very challenging. I wanted to replicate the angles of 55 degrees. But of course my saw wouldn't cut them. So I made a quick jig for my miter saw that allowed the supports to be cut on their side just 10 degrees off 45 degrees equaling 55.
![](/sites/default/files/20141212_100024.jpg)
![](/sites/default/files/20141127_163710.jpg)
![](/sites/default/files/20141202_233435.jpg)
![](/sites/default/files/20141210_164716.jpg)
![](/sites/default/files/20141210_180300.jpg)
Varathane matte touch Polyurethane
Applied stain with Terry cloth covered sponge from Harbor Freight.
4" best roller from home Depot for the clear coat.
Wine Holder
![](/sites/default/files/Wine%20Holder.jpeg)
I made the wood wine holder as a Christmas gift for my mother-in-law. It's great! I modified the plans a bit by routing the curved edges with a roundover bit. It was a great project for some scrap Fir I had from a bed project.
Farm house bench LOVE IT!!
![](/sites/default/files/3154822051_1360780988.jpg)
I have hunted for the perfect dining room bench for my large family but they were either to poorly crafted to withstand my crew, to small, or to pricey. Then I found this site showed the farm house bench to my husband and he said, "Hey I can build that!" and build it he did. He changed a few things here and there but the overall finished bench is AMAZING, and I LOVE IT!!! Thanks Ana!
Printer's Console
Followed the plans pretty close on this one.
Comments
Fri, 12/19/2014 - 17:34
I really love how this turned
I really love how this turned out. What stain did you use? Thanks!
I've started building the Triple Printers Console. I haven't quite decided on the color.
In reply to I really love how this turned by handmadewithash
Mon, 12/22/2014 - 18:19
Stain
The stain was Cabot's Dark Walnut wood stain.
Harvest Bench
![](/sites/default/files/ana%20white_1.jpg)
I purchased a harvest table from a local store that sells only solid wood furniture. The store had the option of purchasing a bench. I decided that I could save some cash and make the harvest bench myself.
For details, check out my blog - http://www.woodworkingfourdummies.com/blog/harvest-bench
Cheers,
Ian
Coffee table
![](/sites/default/files/D18DEC7A-C37D-4D7A-8E65-BDBCD5BA7DEF.jpeg)
My second ever project my wife said I could do followed your plans are use pocket hose after asking about using them and you sent me a link on how to use it. I did not use the X instead my wife wanted me to Make a cross so it would go with the crosses in our living room thanks for the plans.
Comments
first try :)
This took me an afternoon because I have never used a compound mitre saw before so I was teaching myself through trial & error.
It was really fun to try and I will definitly be making more!
Comments
Half-sized Rustic X table
![](/sites/default/files/image_490.jpg)
I used 1x6 cypress wood for the top as well as middle and bottom shelves. This wood was given to me from my in-laws and came from an old corn crib that was torn down on their farm. The remaining 2x2's, 2x4's, corner brackets and screws were picked up as used or broken pieces from a local Habitat for Humanity Re-Store. I also picked up the tung oil I finished with from the same place. The pics show the various stages of build from the initial raw pieces that had been planed/sanded to using Hillary's tea and vinegar oxidation; after a good bit of tung oil was used; finally right before I gave it away as a Christmas gift. I had never worked with old cypress wood previously and was very impressed with how it accepted the oxidation (nice and light) as well as the oil finish. I preserved the old nail holes in the wood as much as possible and you might even notice I left some the white paint from the old corn crib that was on the end of one piece. Great plans - fun little project!
![](/sites/default/files/image_489.jpg)
![](/sites/default/files/image_491.jpg)
![](/sites/default/files/image_492.jpg)
![](/sites/default/files/image_493.jpg)
Finished the table!
We struggled with the angles because we made the table bigger than this tutorial suggests but all in all, awesome build.
Sweet pea bunk bed
![](/sites/default/files/20210126_112810_1.jpg)
Thanks so much for the plans to build the sweet pea bunk bed.
It was just the ticket.
My little girl loves it, we used glitter paint and used some to replicate the stars and night sky on the lower bunk ceiling
We made a little ladder only because of space (or lack of) and will make the shutters and drawers at a later date.
Many thanks.
Dan, Alena and Leonie
![](/sites/default/files/20210126_112810.jpg)
Valspar satin with gold and silver glitter