Community Brag Posts

This was a very simple pot rack and spice shelf using 1x3 for the pot rack and 1x4 for the spice shelf.

Spice Shelf is 7ft and the most complicate part was cutting the uprights for the large baseboards in our house. I used a profile gauge but this wasn't quite enough. Eventually I did some sanding on the spot to get the best fit. Having gained my addiction from Ana for Kreg Jigs the shelves and mounting pieces were added with pocket hole screws. By placing the screws on top or on the bottom I was able to avoid the necessity of plugging holes. Shelf spacing is completely custom for our needs and the large bottom portion will receive a cross brace in the front to hold in our shopping bags. Butterfly bolts were used to mount the shelving through the lathe and plaster walls.

The pot rack is simply a 1x3 ladder where I used a 1x3 for the spacing between the rungs. Large bottom to hold pot lids. Hooks were hand bent using a jig to ensure they were all the same. Mounted to the old brick chimney in the kitchen using TapCons.

Both items were finished in MinWax Mahogany and had one coat of of poly to keep the rustic feel.

Length of project depends on drying times.

Any questions please let me know!

I just finished my first project with upholstery!  I built a bench following Ana's plans from a couple of 2x4s and used this gorgeous fabric from Minted.  Minted is November's sponsor for the Fab Furniture Flippin Contest.  The paint color is Behr's Island Aqua.  I used 3" thick upholstery foam (and WOW that stuff is super expensive).  I love diamond tufting and followed a tutorial from Addicted 2 Decorating.  

The bench is super compfy.  I love it and I love the bright cheery colors.  

Made it a little taller and a little deeper.  

The husband kept complaining that the washer and dryer were too low without pedestals. Well, no problem! I've got plans from Ana's site.

I measured to fit our machines and followed the plans. But somewhere along the way I screwed up. I think it might have been how I attached the legs with the "L" brackets. My legs were sitting away from the base, not flush with it. Anyhow, the way to correct my mistake was to attach the moulding along the sides, front and back of the base, not around the legs. But I don't mind the way it looks. Just an FYI: there was a lot of waste with the sheets of MDF, but that's not a problem because I'm using it in another project as I write. :)

First, I put on two coats of primer. Then I decided I wanted a splash of turquoise in the basement, so I mixed a blue and yellow paint until I got the color I desired. After a few coats of paint, I distressed and then decided to tone down the color a bit with a Valspar glaze. I put on two coats of poly, hoping that would be enough to withstand the inevitable water on the pedestal. I thought the piece was screaming for a quote, so I painted "The most memorable days usually end with the dirtiest clothes."

And you think with the new height he'd help me with laundry a bit more? Yeah, I think not.

Our original sofa and loveseat turned out so well that my parents asked that we build them a set. It was our first time converting the plan to a single seat so I was nervous on how it would turn out, but it looks great!

This TV console was made on request.  Its made from maple plywood and Pine top, trimmed with Small crown,  large chair rail  and base board moulding.  It has one media shelf a larger shelf for Pictures. The very bottom has two 18 inch drawers that are 5 1/4 inches deep for dvds or games.

Followed the plan, adjusted the height to accomadate a trundle bed in the future. Tapered the edges of the 2x6 material for a shaker/craftsman look. If you cut the board at a 25 degree angle the 2x6 material will rest right in line with the 2 x 4 material below. Be sure and add 2 to 2 1/2 inches to accommodate the taper edging.

Used Minwax gunstock stain to match the furniture and three coats of fast drying gloss poly.

I worked on this over the past couple of months (would have been quicker, but you know..life gets crazy sometimes!!)

I used the farmhouse table plans to a tee and then stained and poly'd it. It turned out great!!! My Wife loves it and now all I have to do is build the benches. The wood is cut for them, just need to find the time to do it. This is my 4th Anna-White project. I have also built a bench for the end of our bed, some laundry cubbues, and a day bed.

I love this site and plan on using much more...I have friends and family wanting me to build them stuff...the only thing now...is how much do I charge..... :)

I used 1x2 boards for this project. The smaller tree is the size according to plans (minus the coat rack). For the larger tree, I added 3.5 inches to each piece. 1/4 plywood on the back and used a stencil for the design. I love the way it turned out.

I built two of these bad boys!
I used the cheapest spruce wood as I knew I was going to paint them.
Not sure how much everything cost in the end - maybe €50. Am making 2 beds to go with them too but they'll be a little longer in the pipeline!
I cut the wood myself using my circular saw and joined the wood with pockethole screws.
I painted the tables white and then used a chestnut brown woodstain on the table tops, shelf and knob.
Hard to say how long it took me as I just did a bit every now and again when I had a bit of time.

My version of the rustic rolling kitchen island. Really can't do the x's yet. It's all leftover wood and counter top. I use my other one similar to this as a coffee station.

Building a workbench seems to be a rite of passage for most serious woodworkers. The Entry Level Workbench shown here is a collaboration between myself and Kevin at Kev's Woodworks. I've detailed the design while Kevin and his son built the workbench as a father/son project.

All details including dimensions, parts list, tool list, and a full cost breakdown are included in the link if you would like to build your own bench.

https://www.instructables.com/id/Entry-Level-Workbench/

Made by my husband.

Kitchen cabinet I made with raised panels.

Some more details at:
http://bendrea.wordpress.com/2013/09/22/kitchen-cabinet-2013/

My Second DIY project! It turned out PERFECT :) 

Finally, kitchen is done.  We've been in this house almost 4 years and for me the kitchen was not efficiently functional.  Dishwasher was on the wrong side of the sink, had a trashed compactor which we did not use, very little counter space, not enough drawers, etc.  

The whole kitchen was gutted except for the cabinet over the stove which I covered and still has storage.  

Thanks to Ana White for the plans and inspiration!  Learned a lot during this process.