Modern Slat Top Outdoor Wood Bench
We wanted an outdoor bench for our front entrance way, this one is just what we were looking for! Thank you for the plans.
We wanted an outdoor bench for our front entrance way, this one is just what we were looking for! Thank you for the plans.
I modified the plans just a tiny bit to make the dimensions match the cushions I bought. I got my cushions from Lowes for $57 per set. The other modification I made came because of some of the comments I read on the plan's comment thread. Several people seemed to be worried about the strength of the back section as the back was beveled at a 15 degree angle meaning it wouldn't make a 90 degree joint. Because my biggest fear as a woodworker is having a piece of furniture fail, especially if it fails when someone else is using it, I wanted to make the chair as strong as possible. So, I lowered the lowest back slat so that it's bottom edge would make contact with the seat frame. I also beveled the seat slat at 15 degrees, in fact I built the entire back section and then beveled it all at once. This change allowed me to put pocket holes along the width of the chair. I alternated pocket holes in the seat frame and the back support section. Of course, it is all reinforced when you connect the back section to the arm rests, as well. So far, the chair is holding up quite nicely--as is my pride as a woodworker--and has not even come close to failing. Also, counter intuitively, I put all the pocket holes on the front of the back section. I figured the cushion would cover them, and then the back is left sleek and clean in case anyone wants to admire the chair from the back.
Mon, 06/29/2015 - 09:25
Very nice and they look so inviting. I have the same rug. Love it!
Mon, 06/29/2015 - 14:47
I've been wanting to build this set for so long. The cushions keep stopping me. Did you buy them recently from Lowes? Do you remember which ones they were?
Mon, 06/29/2015 - 21:00
Thanks, handyness! Yes, I bought them from Lowe's about a month ago. And they are still there because I always walk past them and debate if I should try to buy two and make a loveseat.
Mon, 06/29/2015 - 16:07
Your chairs are lovely! What a beautiful build, and love the finish too!
Sat, 11/28/2015 - 22:22
Hey,
Sorry I didn't see this message until now (almost December). Anyway, I added a picture of the modified plans that I drew up. Hopefully you can make sense of them and read all of the measurements I used. Oh, and yes, the cushions are the Allen Roth ones from Lowes. Please let me know if you have other questions or can't read my plans.
Thanks!
My version of the Grandy Sliding Door Console. My modifications:
- Length 6.5 feet long (instead of 90inch). Same height and depth.
- Bought hardware from amazon, purchased hardware is larger than the plans call for. Changed face frame top from 1x4 to 1x6 to create clearance for the wheels and top overhang.
- Wanted a deeper top so I added a 2x3 between the two top boards. I did this also for looks! It stained so nice!
- Modified the mounting spacers for the rail to allow the door to hang closer to the cabinet.
Advice: Pay attention to the size of the hardware.
If buying door hardware make your door close to the same thinkness as a standard interior door. This will help them hang correctly and close the space between the frame and the door.
Lastly, use pocket holes!
Simple design and fun to build. I did not however use the turned legs. I made a jig and went with tapered legs.
Mon, 01/03/2022 - 12:32
Fabulous job, it is gorgeous! Thank you for sharing:)
You probably read a lot of amazing posts here about how people using the plans can make something in a day or a weekend. They deserve kudos for their diligence! But I don't want you to get discouraged if you don't or can't work that quickly. I want to encourage those of you who work more slowly that you can still use these plans. What slows you down? Maybe it's lack of time, health concerns, or cost. I have made and even designed furniture in the past. But prior to this, I always had someone helping out with the building process, used a kit, or the project was small enough that it didn't seem overwhelming. I made this completely by myself . . . and that's why I think you can, too. And while this project took me almost four and a half months to complete, the end result is the same--a place for me to sit and type up these tips for you!
I hope the things I learned along the way may help encourage you to just take that first step toward creating a piece of furniture.
Beginning Tips for Slowpokes:
* Bookmark and print out the plans from the Ana White website, and keep them in a safe spot that you will remember over the months to come. Check the site regularly for updates, corrections, and tips that members share.
* Break up what you're doing into a bunch of smaller projects. The desk, for example, can be broken up into up to seven different projects (the center desk section, the two cabinets, and four drawers), with each being able to be completed partially or completely before moving on to the next.
* Get as many cuts done in stores as you can. You'll need to be careful here, especially if you gather pieces over time. Everyone cuts wood differently, woods have different dimensions (even when they shouldn't), and your pieces may not match up exactly. However, having pieces cut will generally make things a lot easier for you!
* Taking time off from building is okay! If you plan correctly, you may even be able to use partially-finished projects. I took a break before building the drawers, but still used my desk, complete with open shelving units on either side.
* Do what you can, even if it doesn't seem like anything. At times the most I felt I could do in a day was to drive three nails. But then, I was a few nails closer to being done!
Finishing for Slowpokes:
* Pick your paint (or stain) color and manufacturer wisely. Initially, I used some leftover barn red paint for the center desktop piece, expecting to get more of the same paint. After I had put on one coat, it dawned on me that the paint line had moved from one manufacturer to another. I searched around online and discovered that the paint colors changed in the move, not just the manufacturer. Oops. Some paint companies are really static with paint colors. If you plan to create the project slowly, it's really important to be able to trust that the paint you went with will be available in the future if you run out, so that you don't have to go through the trouble of color-matching. I switched to an older brand and a less-trendy color.
* Distressing is your friend! Creating a beautiful stained or painted finish is tough to do, and if you leave your project partially finished, you up the chances of it getting dirty, dented, or otherwise marred. Choosing a distressed finish means you don't have to be as careful, and any little mistakes will be more accepted. When I was painting one of my drawers, a big chip mysteriously fell out of the moulding. I looked at it in shock. Then I thought, "Well, it's distressed!" I could write a whole list of things that are wrong with my desk, including crooked drawer fronts and the fact that they're not flush with the cabinet. But distressing the desk makes it look like a homemade antique, and perfection isn't necessary.
* Write down ALL your finishing steps clearly, including paint colors, brands, and type (example: matte or semi-gloss). Keep this list in a safe place along with the printed-out plans so that you can make each part of the project look the same. Some day it would be my dream to have the entire wall unit of which this desk is just a small portion of. I now have confidence that any future pieces would look at least somewhat similar to the desk!
I hope that these tips have helped encourage you to get started on your dream furniture. Just remember that no matter how long it may take to have that dream fulfilled, the end result is the same!
I loved the Parson Chair plans on this site and wanted them for my dining room! I modified the plan simply by making the chair 2" narrower and the seat back 2" taller. I also made the slipcover removable (and with fringe), so that I could change it up as I wish.
This bench is a shorter version of the farmhouse bench to go with our existing table. It measures 45" long, 14" wide, and 18" high. I used the leftover wood from building our Farmhouse bed so it cost next to nothing. I used leftover 1x4's for the seat and leftover 1x6 for the breadboard ends. I didn't have enough 2x4's to make the 4x4 legs, but decided that the bench was sturdy enough as is. I used my Kreg jig, so I did not notch out the legs as the plan resulting in 9" stretchers and aprons. I did add an extra 2x4 to the inside of the leg piece to add stability and a surface to screw the top to.
I washed the plans for the farmhouse table in hot water!
I modeled this kids table off the farmhouse table and then made the chairs out of 3/4" plywood with bright colours.
I made these to create display space for my son's lego creations.
I think I'm the first one to use this plan. I am a newbie so maybe I made it harder on myself but I diverted a little bit. I did not have 4 inch screws that would work with the treated lumber, and they were going to cost me a very pretty penny to get. I did have a box of 3 inch treated wood screws leftover from when we made the floating bunk beds » {LOVE THOSE} so instead of building each side, I had to build it level by level,attach them all together inside once I was finished. I use some leftover pieces to add a little seat in the trunk and a license plate. you also might have a few scrap pieces that you could use for rear view mirrors and headlights, but I would like to keep this simple and chic. I have a small wood slat piece that I will use for a grill on the front { from an old wooden toddler bed rail} so his car will look just like the tiny Fisher Price one he plays with! I'm still searching for a free steering wheel off an old toy or perhaps I will use my husband's 2.5lb free weight. I think it is perfect if I can figure out how to attach it... and how to get away from my husband ;)
Wed, 07/10/2013 - 14:01
this is my first solo project. I had the store do most of the major cuts so that was a definite time saver. I only had to do my angle cuts and kept on my leftover pieces to do my modifications. this will sit outdoors so I had to spring for the treated lumber. since I built it level by level I had to secure it inside. all except the last trunk level were secured under the hood out of the way. securing the final level of the trunk gave me the idea to use a "license plate" instead of just a random piece of wood.I can't wait to put it in the play driveway to add to his big outdoor play house! thank you for an excellent easy to follow plan. maybe now I can get a plan for a matching gas pump?? :-)
After accepting a job in a skilled nursing facility last April, our son move out of our house, taking with him all the furniture from his room. As a result, he virtually left my wife and me a blank canvas to do as we pleased. My wife wanted to put twin beds in the room, and as such, searched high and low for two adult twin beds, all to no avail. Then one day while looking on Anna White’s website, she saw plans for various types of beds, including adult size twin beds. She printed the plans for the beds and asked, “Can you make these?” I studied the plans for a moment, and said, sure. Because the plans were so detailed and easy to follow, I was able to construct both twin beds over the period of a weekend. For me, I found the shopping list and the cut order to be the most useful section of the plans.
We decided to go big or go home. We made the console almost 8 ft long out of all Rustic Alder. Took almost a month with a few hours here and there in the garage. But everyone loves it and we can't wait for it to find a new home!
Barnboards with live edge provides an artistic appearance, so this project was to maximize live edge, and barn board finished ends.
Barnboards are chosen based on sturdiness, and also unique edges that add character. A jig is used to rip 2 or 3" off of a live edge board. Then cut to length to assemble project. The shelf is cut to length using a 45° miter cut underneath final finished length. Swing the miter saw to Cut a 45° in the opposite direction of the previous cut on the scrap portion, slicing a long triangle, this is garbage. Then cut a 90° slightly past the miter cut, giving a 90° triangle the will fit under the finished edge of your board. The barnboard grains will match up perfectly, as well as interesting dips and curves on the edges. Glue the piece to the finished board, lining it up carefully. Then airgun nails in for extra support.
This is a project I just finished building for someone, and similar concept to what you had in the latest email. I have enjoyed watching what you have been doing. Keep up the awesome work, and encouraging others!
Dorothy Michel
Rustic Timber Decor
I modified this to include another shelf on the bottom. Easier when built by two people.
Tue, 01/01/2019 - 22:41
How come there r no steps to follow for this plan. I’ve made so many of ur items and love watching all ur post to utube. Thank u for ur dedication to better urs and all of our crafts.
We made our sectional higher off of the ground than the original plan by replacing the single 2x4 base with stacked 2x6s, stained it black and used cushions from Target that we managed to get at 50% off. It fits beautifully in our screen porch and has made what was a waste of space into an outdoor living room. Thanks for the great plans!
Sat, 07/13/2013 - 11:10
Thank you for bragging! I am so excited to see your sectional and love the added height! Glad you found the plans useful! Ana
Sun, 07/14/2013 - 08:21
I love what you did with the plan. When we do our Pergola on our patio - we are going to change to this type of furniture or a new farm house table. I love the paint color ideas and the adjustments all for such a great price! Great job!
This was my first major project to build. I modified it to resemble Macy's Captiva bedroom set. I finished it with General finishes lamp black paint with some slight distressing.
There was some deviation from the original plans.. We made the storage boxes a bit taller and the headboard has several new features.
First off, the under-bed storage takes up the whole size of the bed. So the drawers (six of them) are nice and deep. One of the drawers is actually the dog's bed now.
The picture doesn't show it but behind the headboard there are cubbies for storing books, tablets, phones, glasses, etc.
On both sides of the headboard there are four electrical outlets plus two USB charging outlets for charging tablets, phones, etc.
There are two reading lamps on the headboard as well.
I did the construction portion while my talented wife did the amazing paint job.
Rustic X Desk with LED lights and slide-out wood crate drawer w/ antique copper handle. Mix of old and new. 58" across gives me tons of space!! Thank you Ana White for the plans and ideas xoxo
Project and plans were easy to follow. Decided to move the ladder to the foot of the bed so we can make a roll-out desk/table underneath. Also flushed a 1/8" panel board underneath to cover the slats and make it look cleaner. It was a fun first big build, with more to come. Our son loves it!!
Needed a kitchen island and loved this plan when I found it on your website. I have tools to cut the lumber but thought I would let Lowes cut the lumber to save me some time. Ha! Made small corrections with what you need like just 2 2x4s to make the 4 legs. Like Ana said, it's all about math. Thank you for the plans. Friends already wanting me to make one for them, ha. Ps...my dad is sold now on the kreg jig!
Comments
beardjulie
Wed, 05/04/2016 - 10:01
quesion
I am really a novice. The plans say that the 1x4's should be 18-1/2" high? But the measurement of the vertical legs are 14", and the horizontal piece is 4" high, which adds to 18". It all looks flush in the photo. Could you explain what I am missing? Thank you so much!
beardjulie
Wed, 05/04/2016 - 10:01
quesion
I am really a novice. The plans say that the 1x4's should be 18-1/2" high? But the measurement of the vertical legs are 14", and the horizontal piece is 4" high, which adds to 18". It all looks flush in the photo. Could you explain what I am missing? Thank you so much!
In reply to quesion by beardjulie
Rudystawarek
Wed, 05/04/2016 - 11:30
Hope this Helps
So from what i see in the plans Each 1x4 board is to be cut at 18" and the 2x4 is to be cut at 14-1/2". Cutting the 2x4 at 14-1/2" will insure the 1x4 and 2x4 are fluish for the end product. It doesnt seem to add up given the demensional names of the lumber hahaha however the actual width of a 2x4 (the one the will be going horizontal) is acutally 3-1/2". so then you cut you 2x4 leg piece at 14-1/2" and then lay the horizontal 2x4 on top the total height will be 18" and should be flush with your 1x4 that is cut at 18"
beardjulie
Fri, 05/27/2016 - 14:04
yes!
That is too funny! That is a dead give away that I'm new at this! Thanks you!
beardjulie
Fri, 05/27/2016 - 14:04
yes!
That is too funny! That is a dead give away that I'm new at this! Thanks you!