Tidy Up End Table
Fun little project, think I used too many pocket holes, they are really visible, all well, take what you learn.
Fun little project, think I used too many pocket holes, they are really visible, all well, take what you learn.
Thanks for the wonderful plans! This is my 2nd Ana White build (traditional turned leg, pottery barn desk). I used the legs from this build and then leveraged some tips from another blog for the herringbone top using 2 sheets of MDF as a base (http://www.southernrevivals.com/2014/06/tile-top-herringbone-table-make…). My herringbone table took some planning, as it is over 13' long. Now all of my family can eat together when we get together!
Wed, 04/29/2020 - 16:56
This is absolutely gorgeous! I love the unique top you did with the herringbone pattern. I've been debating on trying something similar myself 😁
Thank you Ana!
Love your site!
That was my first wood project, and it turned out awesome!
Here are the unfinished, and the finished version, with transparent matt lacquer.
I also added some wheels for easy moving around.
Yokhai
I was looking for a small entertainment stand that would fit our blu-ray player and cable box, but also some drawers to hold dvd cases. This looked perfect. I have some woodworking experience but not a lot. I've never built anything with drawers before and I was a little nervous about it. The drawers were definitely the most challenging part and took some modification. If I built it again, I'd rip an extra 1/4" off the drawer sides so they'd fit better vertically. Other than that though, the plans were great. The project turned out very nice and I'm very happy with it.
Thanks for the great plans. I got your book for Christmas!
Measuring 8' long, 36" tall, 20" deep, and weighing nearly 400lbs, this is truly a MEGA BUFFET!
Cabinet Materials: 3/4" cabinet-grade birch plywood sub-frame. 1/4" V-groove rear paneling. American Poplar face-frame
Top: 2-1/2" thick American Spalted Ambrosia Maple flitch
Hardware: Custom
I built this chair out of scrap lumber and leftover stain I had on hand for proof of concept. I love it. I’m calling it the sherbet chair, lol. I’ll definitely be making more in the future. I learned a lot in the process.
I built these for my son for Christmas. They were very easy to build (the 2nd chair turned out much better than the first, however!) and I am very pleased to have discovered this site. Thanks!
I made the countertop with 2 plywood boards screwed together and topped the stainless steel with heavy duty adhesive. I adjusted the plans a little to accommodate my space. Thanks for the plans! It was a fun build!
This is my more traditional take on the modern craft table (I guess that means it isn't technically "modern"!). We call it the "Lego Table" at our house. I doubled up the ends like others have so that my two daughters can have their own sides. My wife asked that the there be backs on the side shelves so that items aren't pushed off. I also added trim around the tabletop and molding to give it a bit more traditional appearance. Finally, I made the shelves adjustable.
I’m very excited for my first project. Not to be boastful, but I am very proud of myself. So my wife decided she wanted a kitchen island. I began from the top of the plans and about halfway through I realized I have a small kitchen. The wife came in and said “that’s way to big). So I had to make a lot of adjustments. For instance, the 4x4 legs became 2x2. I was afraid it would not be sturdy enough, but it turned out nice. I left out the portion of the plans for the range and just made a bigger shelf to accommodate my wife’s mixers and other large kitchen items. Instead of a second shelf I made a slide out trash can (single instead of double). It fits the kitchen well and more importantly the wife loves it. Now to build stools. Thanks to your site Ana, I was able to make a place for my family to have dinner together. My daughter helped me with this project and has been asking when we will start our next project.
Sun, 10/18/2020 - 12:50
You did a fabulous job, huge pat on the back! Can't wait to see your next project!
If you'd like to build a very inexpensive chair and bench for your boat dock out of just 2 x 4s and 1 x 2's that is extremely sturdy, then this project is for you. As you can see by the picture, I used the Kreg jig, 2 cordless drills. Also a chop saw to cut the materials.
Wed, 01/02/2013 - 20:23
These are great! Where are the plans for these??? I've been looking for a bench just like this.
I found your plans last summer and loved the design so I decided to build one for my wife for her birthday last August. I didn't get started until the weekend of her birthday in late August so there was little expectation to have it finished before winter. It is now 14 months later and I only have a few trim pieces left to install. We live in a harsh climate and I wanted to be able to use it through the winter so I made a few changes. I built a 2 x 12 base and insulated it with R40 and the bottom walls are 2 x 6 instead of 2 x 4 and are insulated with R20. I used twin wall polycarbonate instead of the corrugated lexan because of the superior R factor. The insulated walls are of course vapor barriered and I covered them with tongue & grove cedar. I also made raised benches out of cedar for growing potted plants on. The floor has ceramic tile on it and the exterior is colored metal. I also ran underground power to the building and installed a fluorescent grow light. Surprisingly a small 110 volt heater keeps the temperature above freezing even during our awesome -40 winter temperatures. If the daytime temperature is anywhere near or above freezing we have to keep the screen open in the door or it overheats inside. I have attached links to a few pictures of the almost finished product, ready for another winter full of flowers and veggies. I initially used clear vapor barrier until the twin wall polycarbonate showed up. This worked rather well.
I have posted this in the comments section as well, but I think it belongs here.
Sat, 03/21/2020 - 09:42
Love your ideas! I have a few questions if you don't mind. Where did you buy the polycarbonate sheets, and what sizes were available? Did you end up changing the plan a bit to accommodate the vertical sheets? Did you seal top and bottom with foil tape and dust tape respectively or poly flashing?
Any help or advice would be appreciated very much.
JB
This is a shorter and wider (and simplified) version of the Flat Wall Book Shelf. (Approx 48" wide and 40" tall). Trying to maximize wasted space under sloped ceilings. I did jig-saw out a notch for the baseboard so it would be secured flat to the wall. My only regret is that I didn't put this baby up sooner. I've been kicking books around this room for years!
This was my first woodworking project and it was fun and easy. A few words of advice though...painting the wood first is a good idea. I did not so it took a bit more time. Using glue instead of staples would make the finish much nicer as you can see my staples, but it is rustic so that's okay. Thank you Ana!
The decorative 4-Foot Mantel Wall Shelf Plans resembles a fire place mantel and makes a beautiful place to display photos and other decorations. The project can be built with a miter saw and table saw in 2-3 hours. A keyhole router bit can be used in lieu of mounting hardware. I also suggest a pneumatic air compressor and 18 and 16 gauge nail guns. The overall project dimensions are 48 inches long by 8 inches tall. It looks beautiful with a glaze or distressed finish. The detailed plans can be found on my woodworking blog at: http://www.jrlwoodworking.com/
Fri, 01/04/2013 - 12:33
We actually built this one to give to my mom for Christmas last year. It looks great in her living room and we put family pictures on it. It's one of my favorite shelves because it looks so classy.
In reply to Glaze? by Nathan1342
Mon, 01/07/2013 - 13:51
I bought a clear glaze at my local hardware store. I had them tint it to a really dark chocolate brown color. It turned out perfect, just what I had imagined!
Pottery Barn inspired toddler bed, made with reclaimed lumber from our home reno. The wainscoting is real (not mdf), $2 from the HD cull lumber rack. It had a damaged piece, but the remaining part of the board sufficed for this small project. Screws are countersunk.
The curve is elliptical (drawn with loop of string and two nails for foci, transferred to board and cut with jigsaw)
The construction is lighter than the original plan, using what was at hand and for a young toddler.
Ever since we've moved into our new home, My Husband Matt has put his room (Or "Man Cave" as we know it) on the back burner so that other things could be done first. He has been so sweet about letting me use it for home decor, event decor, clothes, and misc. storage.
Well, since the hectic first couple of months as new homeowners is starting to die down, I had made my mind up that I would help him get started on his Man Cave as an early Birthday present! He deserves it!!
In passing, he made a comment to me the other day that he would love to have some kind of rustic window treatments in his room. I pulled up Pinterest and nonchalantly pointed out a couple of ideas to see which one he liked the most. We went in the room together and he started to describe what he wanted them to look like. (Again, he was saying this in general. I doubt he thought I was crazy enough to attempt it. Welllll…)
The next day I worked on my usual “project prep” routine:
I first measured the window casing. (My window casing doesn’t have crown molding around it on the sides or at the top, which was a plus! This will make them easier to attach!)
My window measures 35″ wide and 58″ tall. So, here’s how I figured the math:
So, after my cutting was all said and done, I had:
(2) 9.25×58
(2) 7.75×58
(2) 3.5×58
(4)3×17
(4)3×3.5
My wife wanted a console table for our dining room but the original plans were too big for the spot next to the grandfather clock, so I shortened them a bit and this is the result.
Tue, 10/27/2020 - 11:56
Love the two tone finish and great mod to make it work for your space!
I built the flat wall bookholders to go with our new bunk beds! We love them! I built the small, 24" shelves.
I have built this table following the plan from the woodwhisperer website under the name "Not So Rustic Outdoor Table", Used white pine