Community Brag Posts

Used 1 x 4 cedar boards for the legs and backs and 1 x 6 cedar deck boards that were left over from when we built the deck it is sitting on. Built 6 armless units and one corner unit. Total the sectional is 10' x 6' with two 2'x2' ottomans. As everyone else states, the cushions were the most expensive part of the project. We purchased these 8 Sunbrella cushion sets from Home Depot for about $600. After cutting all of the pieces it really did not take that long to assemble the units. I ended up building a little "support bridge" that I rested the unit on so I could attach the back legs since the front legs are attached first. This way I knew the legs would end up level without having to measure, attach the back legs and hope that the legs would end up level. With the front legs resting on the ground and the rest of the unit supported by the "bridge" I could set the back legs in place, resting solidly on the ground and attach the legs to the seat, with no measuring needed.

I took the “classic bunk bed” plans and changed them to accommodate my 3 girls. I have 9 ft ceilings so I just stretched the traditional plans out to allow the 3^rd bunk to be added. It turned out nice and my girls enjoy it. I also built a matching toy box that is visible in one of the pictures. Please excuse my messy shop. I built this with my 40 year old shopsmith and a kreg jig. Thank you for the plan.

This project was a lot of fun to build. I always learn something along the way. The sideboard filled the one wall in our kitchen, taking the place of a bench and a drop zone for miscellaneous stuff. Now we can keep those things out of view with proper storage spaces. 

I routed a channel into the front and side pieces of the drawers so that I could slide the 1/4 plywood bottom in. I then screwed the bottom to the back piece which I ripped down to size. This way if I need to change out the drawer bottom I can just unscrew it from the back and replace it if needed.

i also chose to finish the back up a bit more in case we decided to ever move it off a wall in the future.

Thanks for the great plans Ana!

The kitchen helper tower was a fast and easy build, the modification of 16 hinges to allow the tower to fold flat was actually the most time consuming part of the build. I added clear skateboard grip tape to the platform floor. I found the hinges and griptape on ebay and most of the wood was scrap leftover from other projects.

I really like all the furniture at Pottery Barn but hate paying the high prices. I saw their Cortona Buffet on day and decided it would make a great addition to my dining room. I started out by making a simple frame out of oak, put a bottom in it and built the sides. The drawers were inset drawers and i wanted 1/16 of an inch clearance on all sides so I made some simple drawer slides out of wood. You can kind of see them on the last picture. They worked great! Drawers fit perfectly and didn't have to spend extra on drawer slides. The top is 1inch thick oak that I distressed with a variety of tools to try and achieve the same weathered look as the real deal. The only thing I wasn't able to keep the same was the bottom trim. I went to ever custom molding and trim place in town and no one had anything like it. So I settled for a little less ornate piece but I think it came out well. The hardest part of the entire process was making the tiny trim pieces that fit on the door and on the sides. I had to make my own scratch stock and scratch them out of a piece of oak. If you've never had any experience with scratch stock (I didn't) Google it and try it out. You can make some pretty nice custom trim pieces by hand. All in all it was a nice build, now the wife just needs to decorate it!

First time builder.

Our 19 year old daughter moved back in with us and we had to put her in our den. This room doesn't have a door or closet. The closet system was priority one. She has a ton of clothes. We followed your plans to the letter, but didn't add the shelving in the middle. She wanted a space to put her dirty clothes basket. This was the perfect solution and super inexpensive and easy to make. 

I was inspired to create this after seeing an article somewhere where Ana created her own old "laundry" sign. She used the same idea using the Numbered Cubbies plan. We just purchased a second home in the White Mountains of New Hampshire and it has 4 bedrooms. I'm decorating each with a season in mind. I wanted something to go across the top of the windows.

So, off the the landfill I went. I was looking for an older piece of wood. Low and behold, found one that was perfect. It already had a weathered stain, so I just added a cream paint and then a light green paint. I sanded it off in areas to distress it. Next, I found a quote that I liked ("Spring is when you feel like whistling even with a shoe full of slush") and changed the font size to fit the board. I printed out the quote (on 8 pages) using only the outlines as not to waste ink (Ana's tip). I put the pages up to a window and traced over the lines with a soft lead pencil. Next, you line them up on your board and then rub the pages down so the pencil lines show up on the board. Next, I hand painted the words in. I really should look into the paint pens. :) Finally, I did a very light hand sanding of the words to make them look aged.

I love it. :)

This is the prototype build for the Pirate’s Treasure Trunk Plan. This build was made entirely from scrap wood and left over finishes on hand. The only items purchased were the angles used for the hinges, and the decorative hardware. This really is a great project for scrap wood, since it really doesn’t use much at all. I used the miter saw to cut down some pieces of 1x12 scrap to the 1x4 and 1x6 sizes to build this.

For the finish on this one, the first coat is a gray paint wash (just regular gray paint watered way down and then wiped off), then a Walnut glaze (Minwax Express Color in Walnut + clear mixing glaze) brushed on and then rubbed off. I didn’t sand after the paint wash coat, because I wanted the glaze to stick to the texture of the paint on the wood. The goal was for the weathered wood look of a trunk that may have washed up on shore from a pirate ship. Then it was top coated with clear poly. The hardware was spray painted with Rustoleum Oil Rubbed Bronze spray paint. The decorative nails were left natural. I think they hint at the big chunky bolts that might have been seen on pirates’ treasure chests. Originally I was going to paint the “keyhole” on, but then it occurred to me to use a little scrap of foam shelf liner, cut to shape using the painting template from the plan. Last, a coat of mod-podge was added over everything.

When I was doing the plan I added a couple of alternatives for the decorations (painting all of them on, or adding with mod-podge), since everyone might not like the actual hardware. But, I’m very happy with the look and glad I tried it!

This was a super simple build which took less than an hour to build and sand. Finishing took a few minutes at a time throughout the course of a day. I think the longest part was being patient enough to wait for everything to dry. I let the glaze dry overnight before adding the poly and hardware.

Overall it was a fun and very easy build.

This table was made following the Ana White plan for the 8' table. I stained the whole thing Dark Walnut. I the rubbed Vaseline on the edges and anywhere else that I wanted distressed. I painted the table with a light coat of white chalk paint and sanded it to distress it after it dried. After getting the look that I wanted I applied a clear wax.

Changed the side aprons to 4" for more depth to a storage compartment. Hinged the seat and added a bottom tray. Stuck with natural wood to match the Ikea desk. Fun project. Thanks!

Our daughter is fast approaching 2 years old and had learned the word "chair." She wanted her own, clearly.

In addition to being my first brag-worthy project, this is the last thing I built before I got my Kreg Jig, but even without, I'm quite satisfied with the end result, and it will support me sitting in it (at over 200 lb) so I did something right.

I ripped down some 1x8 to make the lumber required, so it's not exactly per the plan, but it's pretty close. I also made the back legs of out ripped 1x4 because I felt it looked nicer, and added the brace between the front legs only in order to maintain stackability. (For I will be making a few more of these.) My favorite personal modification is the accent heart in the back slat.

3 chairs- Love that these are strong enough to hold even me. I placed these in the bedroom as lounge chairs in front of the TV (see http://ana-white.com/2013/09/mini-media-center)

Forgot to mention, part of the cost I figured, was $250 for mattress and sheets etc. 

Here's my take on the Tryde Coffee Table. The only modification that I made was in the legs. Instead of untreated 4x4s, I used a 2x4, 1x4, 2x4 sandwich.

I also made the legs detachable for easy transport. This was done by drilling holes in the side piece and then screwing in these magic "screw/bolt" things [picture 5] into the leg. To assemble, I just pushed the legs through the holes, and then put a washer and nut on the bolts [picture 4].

[Candlesticks are made from logs with a hole bored in them and the coasters are coiled sisal rope held together with hot glue]

I built this cooler box using the plans posted here by "Jenny from Birds and Soap". Great plans, easy to follow. Thanks Jenny. As you can see, I made some cosmetic changes.  The clock and "rare earth" magnets behind the front panel to catch the bottle caps. I also added a hook for a towel on the side. Turned out pretty cool looking.

Made a few modification s but followed the general pattern! Absolutely love my 10 foot table!