storage for totes - can be made to accommodate any size totes - just adjust the measurements basically it is "ladders " 2x4s for legs 2x2s for "runs" 2x4s across the bottom & top this is in a basement with short ceilings so if you have a taller space you can go taller or you can go shorter.
Farmhouse table made from distressed (worm hole) maple.
My neighbor was able to get me the 5/4 distressed maple for about $2/bd ft - I ended up buying 100 board feet and had plenty leftover. The finished board feet for this project was about 60 if I remember correctly. So the $200 was the bulk of the expense. The only other costs were sand paper, I bought a Kreg Jig, screws, Minwax Marker, paint, stain and urethane (much of which I already had).
It came out better than I anticipated. The antique white finish was not difficult at all.
Tip - When following the instructions for the finish here, I applied the first coat of urethane with a brush almost immediately after applying the Minwax marker to all of the sanded edges. I did this in haste, but ended up with some unexpected results that really added a nice touch. The stain from the marker incorporated a bit into the urethane as I brushed it giving it an antique, yellow hue. At first I thought I made a big mistake, but it turned out to add a really nice look.
Mon, 05/19/2014 - 07:29
CSaintD - The top can be removed as I did not glue it. I set 3 dowels on top of each of the 2 legs so that the top would always lign up correctly if disassembled and reasembled. The stretcher could be removed, but would probably cause some damage to the finish as it was a tight fight when I finished it. The stretcher would be removed by removing the dowel pegs that I fabricated on each leg.
In reply to Disassembly by g82martin
Mon, 05/19/2014 - 08:21
Thanks. I really like the dowel pegs on the legs/stretcher. Very nice top finishing as well. Did you square the boards to get them to be so smooth when joined?
Mon, 05/19/2014 - 08:26
I cheated a bit on the top. My neighbor who got me the wood works in a furniture reupholsery shop. He planed and joined the boards for me, which saved me a good amount of time. I'm confident I could have done this at home with my table saw, miter saw and hand plane, but what he did in 2 hours probably would have taken me 10.
Fri, 08/05/2016 - 20:35
Love the dowels you added! Planning on building this exact table pretty close to your dimensions and have a very long church pew as well! Trying to decide between L-ing my pew and cutting to straigjy 6'. Do you mind sharing the dimensions of your pew? And how did you miter the pew?
Tue, 01/21/2020 - 09:40
Beautiful table. I love the pegs added to the legs and stretcher, they add a historic detail lost in a lot of today's building techniques
Followed the farmhouse instructions - worked great!!
The two tone finish matches the table I built
This site as ever so helpful and vital to the completion of these chairs. Honestly,this project was the first time I had taken stock lumber and constructed something from it. I am handy by my own account,but never attempted anything like this before. Great site. If not for Ana white and this website,I'd have 2 less chairs. It is very rewarding building something from scratch. I'm sure this was the 1st of many projects and ideas I will get from this site. A+++. Thank you very much.
I shrunk the size and dumbed down the plans to fit my skill level.
Mon, 10/10/2016 - 09:08
I love what you did! It looks so great! I prefer this style, which is more simplistic than the other. Great work!!
Mon, 10/10/2016 - 10:28
Love how this turned out - the simpler drawers is just as (if not more) beautiful!
Tue, 10/11/2016 - 14:56
Thanks! I wish I would of set up an account before I posted so I could get notifications. I honestly didn't think anyone would notice it :)
Tue, 10/11/2016 - 14:58
I am so excited that people noticed this :) Is there any way of putting this under my account? I didnt make an account until today and I would like to get notifications. I have my project on my facebook page and can prove that I made it with other pictures. Thanks!
Mon, 01/20/2020 - 07:44
I would love to see this in a farm-house (rather than rustic) aesthetic along with drawers under the seats for extra storage. Maybe on casters with a fold up extension on the other side? So many ideas running through my head with this!
I needed an outdoor dining table for our very long narrow paved side yard. I looked just about everywhere for a table I liked and that was even reasonably priced. Gotta be honest, there was no way I was paying $1000.00 for something I didn't like. That's when I stumbled on the plans for this table on Pinterest. I have never built furniture before, but I had just finished building a privacy fence so I thought I would (could) take it on. It took me about 4/5 hours, by myself, to make the table and I practically burst into tears when I saw how stunning it was!! I altered things a bit and used three 12-inch boards rather than six 6-inch boards (and I used 1/2 inch spacers so that rain water could move through). I was so excited by the table, that the next day, I built the bench! Same alteration as well. I used a single 12-inch wide board (with a gorgeous raw edge--sanded for comfort and safety) for the seat. I'm so damn proud!!! Thank you so much for this spectacular plan! It has inspired me. My next project is the Farm House bed frame for my teen daughter!!!
When it was time for a big girl bed for my daughter I was so excited because I had been WANTING to make the Hanging Loft Bed since first spying it on The Bumper Crop and Ana White. I'm a novice so this was the perfect first project for me and my daughter LOVES it. If you have unique space challenges in any of your bedrooms this is the bed for you.
Wed, 09/12/2012 - 23:10
That turned out great! Very well done first project.
Tue, 12/18/2012 - 17:17
What a great idea! I can't wait to make one for my little girl next weekend. Can I ask a few questions? How did you affix it to the ceiling? I will not be able to get on top of the ceiling so I will be finding he joists with a stud-finder. I assume you screwed in eye-bolts?
How did you make the rail and ladder? Any help is GREATLY appreciated. Thanks so much for the idea, my Daughter is going to love it!
Thanks,
Rob
Tue, 12/18/2012 - 20:48
Thanks Rob!
I replied to you on the blog...
Jennifer
Thu, 08/01/2013 - 06:03
I just wanted to say that I just came across this and absolutely love it! My daughter and our new baby will be sharing a room and now I have inspiration on how to make it work! Can't wait to try this out! Love the ladder...how did you make the ladder?
72L x 18W x 36H
Stained with Minwax Early American, and sealed with Polyurethane. In the process of completing a 2nd to make a set
I made this using plans submitted by pericles49. Thank you, pericles49!
I altered the design to use materials I had laying around, and changed the size to fit my space. That made it take a little longer - especially because changing the fastening pattern is still tricky for me - trying to keep screws from hitting each other.
Design
I made mine a little deeper 27-1/2" instead of 24 on the plan.
Materials
What I'd do differently next time
I wanted a good flat and level workspace to continue projects. This workbench folds up to the wall in my garage so I can still park when not working on anything. I made it pretty stout with 2x4s and 2x6s since it would need to support fairly large pieces of furniture without deflecting. It is very heavy as a result though (good core workout folding it up and down :) )
I used two folding shelf brackets on the legs to keep them from accidentally being kicked out from under the table while it's out. (http://www.woodcraft.com/Product/2001690/2615/Folding-Shelf-Bracket-8-P…)
I used four heavy strap hinges to connect the table to the 2x6 (which was lag screwed into studs). Two gate latches were used to secure the edge of the table to studs when the table is folded up.
I cut the legs approximately, and then when the table was hung I cut and shimmed them to get the table level on the uneven surface of the garage floor.
Fri, 08/15/2014 - 16:32
I really like this fold up bench design. It may be heavy, but I bet it's incredibly sturdy. I also have a really compact garage. I have pegboard on my walls, so a bench that folds UP doesn't work for me when I want to get a tool.
My own bench is more light duty. It's a sheet of 2x4' plywood attached to a frame made from dimensional lumber. It folds down so I have access to the tools at all times. It's based on a design on the Family Handyman website, although you can find the same design all over the web.
Thu, 02/05/2015 - 18:50
Great idea! I need to build this. Can I please get a picture of it folded up, so I can see the hinges on the legs and the latches holding it while folded?
Fri, 11/06/2020 - 13:55
Can you show another picture of the hinges you used on the legs that can fold out when lowered?
Thanks! Kate
Full size storage bed with trundle. Three drawers and a trundle on one side and four drawers on the other. I started with the farmhouse design (headboard and footboard) and modified it to make it not so heavy and I designed the rest using SketchUp. See more photos in blog link.
Thank you so much for this so easy plan! This was perfect! I shortened the overall length to 48" to fit our entryway. I got to make use of my Kreg Jig & was able to make use of upholstery fabric samples I had collecting dust. Used 3" foam covered with 2 layers batting, then put together the several samples into a color block setting. Stitched with french seams & squared off the corners before nailing down to the base. I didn't have a guide other than my eyes for the nailheads & chose to spread the 128 nails out every inch rather than closer...served to hide any waivering off & I preferred the look. I also found out that using a 2-sided tape like binding tape or Wonder tape for the cover was very helpful in keeping everything straight. The base is stained a dark walnut & finished with 2 coats of clear semi-gloss Varathane. The seat bottom is 5/8 MDF.
Tools used:
Circular saw
Sander
Pockethole Jig
Sewing machine & serger
I really needed somewhere to park my rototiller and mower during the summer and ended up modifying the plans to include a lean-too/over hang area. This required flipping the shed to extend the roof line. I continued the 15• roofline and also then had to create and cover the soffits. I also reduced it to one door and placed it on a skid foundation so that technically it would be considered a temporary structure, no permits needed. I first used a semi transparent stain that looked much darker and grayer in the store but looked very blue and terribly streaky on the shed, see back wall area. I then restrained it with a solid stain, which I think looks much better and covered the streaky stain. Because I extended the roof and stained it twice, this really increased the cost, but I think it was well worth it. I can store all my yard and garden tools underneath and inside.
I finally finished my workbench this summer. I started the bench 2 years ago for my miter saw. Got busy with other builds, things for family, clients, etc. I still had most of the wood cut for the carts. Here it is in all its glory!!! Finally organization and I can actually park my car in my garage. Thanks Ana for all of your plans.
5 1/2W x 5 1/2L x 8H.
Ana made this project very easy for me. I did the main building while hubby cut the wood & helped drill in hard to reach areas. Thank you Ana for boosting my confidence. I’ve never done anything trike this.
mortise and tenon joints with dado for breadboards
Making several of these for family and friends this holiday season. - Frank Thomas
Thank you Ana for the great plans! We adapted the project for wood we had on hand. It is only 40 inches wide instead of 42”. Our widest pallet board was only 40”.
Thank you for continuing to inspire us! We made two couches a couple of months ago. Great plans!
Great Plans, I had a blast making this table for my wife! It turned out great. Thank you for sharing the plans for this beautiful piece!
-Mike
Thu, 12/27/2012 - 09:21
Your table turned out fantastic! I'm glad to see that because I am considering this table for a project in the near future :)
Thu, 12/27/2012 - 12:30
Your table turned out just beautiful!! Great job and I love the finish!!
Sun, 09/14/2014 - 13:45
Love your table!! How did you attach the 1x6s to the frame? I am stuck at that step! Thank you for your help!
Reclaimed this wood from a >100 year old home that was being renovated. This is just the couch portion, I also built the sectional part. I really like how it came out.
