Community Brag Posts

This is a Pottery Barn inspired headboard. You can see from the pictures posted that I used 4 different kinds of wood. Reason being that money is tight and I had extra wood laying around the garage. I really enjoyed this project thanks to Anna's post here http://ana-white.com/2010/03/plans-mason-headboard-its-all-in-finish.ht…. I noticed there was a lot of posts concerning the finish. For my headboard I used 2 coats of primer, sanding in between coats. 2 coats of paint. 1 coat of chocolate glaze ( 4 parts glaze, 1 part stain). 1 coat of sealer. I followed this post for my finish http://ana-white.com/2012/05/distressed-turquoise-chocolate-glaze. Good luck everyone. Feel free to ask questions.

- Brad

Build time: 2.5 hours
Painting time: 4 hours
Building cost: Free (reclaimed wood)
Painting cost: $25-$30

This was my second project off Ana White's website. The construction was not as difficult as I would have thought. The staining on the other hand was very time intensive. I made an amended version of the table since I only wanted a 1x12 vs. 1x16. All in all, I am extremely happy with how this turned out.

Laundry Sorter

We are expecting baby #4, and I knew we needed to get the laundry under control before we added a new family member. I cannot tell you how helpful these have been for eliminating laundry piles and encouraging our kids to put away their own baskets. And I splurged on a $9 gallon of "oops" paint from Home Depot to make them fun and cheery, too. I highly recommend this laundry sorter project for those who feel like the laundry never ends. It's such a great investment in your sanity!

Finally finished my outdoor space just in time for the start of summer! Thank you for sharing the plans and instructions. I also made the beginner dining table for my outdoor eating space.

We have Pottery Barn furniture in our cottage and I wanted a bench for our bedroom. I found this plan was very close to the "Benchwright" style and I'm very happy with the results, including the match in stain colour. It cost me approx. $40 vs $650 at Pottery Barn. The effort was definitely worthwhile !

I needed a table to fit in the gap of my offset and back to back couches. I made the bottom shelf a little bit longer to better fit the space. I also added additional screws to the back for more stabilization since I knew my kids would find the steps irresistible. The different hues of blue make it more interesting.

My boyfriend and I made this farm style table based on plans from Ana's site. We LOVE it. We wanted it to appear rustic with natural woods tones so we used Special Walnut Stain, Poly, and Light Brown Briwax. Even though it looks raw, its silky smooth to the touch. 

Thanks for posting these plans! We already on to our next project. We have the wood purchased for the rustic coffee table and console table, and I have my eye on the farmhouse bed frame and a set of night stand tables. 

Kate

Sarah loved your Nested Grill Cart build however, the plans called for a 5 foot wide cart and we only had room for 4 feet on the back deck. Made the appropriate adjustments and went to town. Turned out well and Sarah is quite pleased with how it turned out. Adding a shelf for needed storage.

I have always wanted a hall tree, but could not spend the hundreds of dollars for one. I was so excited when I found these plans.

I had a very hard time finding baskets to fit the cubbies. I thankfully found some cheap ones at Wal-Mart that were a two pack of the small and large. I would recommend buying the baskets first, then adjusting the plans.

I hung the shelf with three heavy duty D ring hangers, and then added three screws drilled directly into the studs. We have four rambunctious kids, and did not want the shelf falling down on them. It is super sturdy! I love this piece of furniture so much!

I was new to building when I built this. The X was very scary for me so I chose not to add them. 

My son was looking for some type of planter for his front porch and could not find anything that suited him. I seen these plans on your website so my wife and I decided to try and make these for him as a surprise. These are very simple to make by following your plans. Our son loved them and is wanting two more. Thanks Ana.

Junior loft bed built using junior loft plans

In addition to adding two matching benches (idea from another post based on this plan), the following changes were made to the original plans:

1. Shortened the length of the table by about 14 inches.
2. Cut notches into the leg posts for the aprons to rest in.
3. Eliminated the stretchers (my wife didn't want them).
4. Cut the square 4x4 posts to an octagon shape (wife didn't want square legs)
5. Trimmed edges of 4x8 and 4x10 boards (wife didn't want the notches in the top caused by the rounded edges).
6. Used biscuits in addition to the pocket hole screws to assemble the table and bench top pieces.
7. Used a 1/2" rounding bit and router on the top and bottom edges of the table and bench tops.
8. Attached 3-1/4" Floor Protector Gripper Furniture Feet to the bottom of each leg.

End result: a very happy wife!

Made two of these twin Kentwood Beds for my boys by myself! Super easy and a never study bed! Can't wait to decorate their rooms now!!

2x4 sofa with 1 arm sectional.

I built these nightstands to replace the mismatched ones in my bedroom. I'm going to use the lower shelf to charge my phone, iPad, and things like that. It'll be nice to have them out of the way.

This was a very easy build, but it took me a while to make, simply because I made a pair and there was a lot of cutting to do. I had never done drawers before, and they were a little tricky at first, but by the time I got to the last one, it went on super fast! Ana's plans are very clear, and easy to follow! Thanks Ana!

Made this desk custom for a friend and I am so happy with how it came out. Took around 4 days with finishing. I didn't put a back on it because drilling those holes for cords always goes rather splintery. If he wants a back we can easily put it on. The top ended up having strange coloring with the Dark Walnut stain, I think because of the wood filler, but I like it because it gives it a rustic old world kind of look. I saved a lot of money by hounding the scrap bin at Home Depot several times a week, looking for wood on Craigslist, and raiding my leftover stash. I modified the side so there was a tower partition and a shelf on shelf pins- courtesy of Kreg shelf pin jig. I used moulding I had sitting around to cover the exposed edges of plywood.