Customized Step Stool
i took the step stool plans and using imagination and a CNC router put themin a new "catagory". John Ogren
i took the step stool plans and using imagination and a CNC router put themin a new "catagory". John Ogren
We had to get rid of our standard dressers awhile ago, since they were in awful shape. We tried only hanging clothes, but that was a disaster too (our daughter stood on the wire shelf). I was so excited to find these plans. The dresser is super sturdy and was easy to build. No more problems with standing on them, heck I could even stand on them.
The angle iron was really expensive, so we went with wood rails instead. It was super easy to do and really cheap.
I used the basic bunk bed plans from the site, but made it a bit taller (21.5") and fitted a drawer under the lower bunk. The girls can store some of their Maplelea doll clothes in it.
This was a fun project to build. I did change somethings around. I used plexiglass on all doors instead of plywood and it turned out great. Took a lot longer than planned but in the end it was worth it!
Fatbike rack! Ten minute project for the beginner. Heavy enough to keep your bike standing upright even in windy conditions. Great if you are short on space.
(2) 14" treated 2x4
(2) 28" fence posts
(8) 3 1/2" outdoor screws
6" space between the fence posts
Alter width, if needed, for your bike tire.
No part of the bike hits the wood except the tire.'
Deanna Peterson
I watched the tutorial video first and then got right to it. My two, little boys played in the driveway while mommy rocked her off-square bevel cuts. I modified the 1x2 and instead used what I had on hand - extra 2x2s. Worked out great. Also, I used three reclaimed pallet boards for the top of the bench. I added an extra cross-support to handle the load.
This is my first time trying something like this and it went great. I did mine with 2x4's. Thanks for all the great information. This took me a week, but I was only able to work on it during nap times for my baby. Uninterrupted it would of taken a weekend. The only negative thing is now my wife wants me to tackle a Farmhouse Table with benches. Pics soon to come of that I'm sure. Thanks again!
Love, love, love this plan! Easy to understand and build...it was sanding all the parts that took forever! ;-) It's been on my build list for a couple of years, and now looks great by my pool. I did use a more traditional arm style for the chair's 2 arms. I added the "table" between the 2 chairs by using scrap 1x4s, aligning them for spacing then used a chalk line, from corner of back arm 2x2/2x4 connection to the front 2x2/2x4 connect, and snapped a cut line. I then used a 1-1/2" hole saw and drilled a hole opening for the umbrella.
Thanks Ana! This is the second Ana White project I've tackled for the pool deck.
This was our first wood-working project, and it was a BIG one. I think it took us about 50 hours, though we did add a couple complicating steps into the process. We installed full-extension drawer glides and stained instead of painting. Both of those added significantly to our time. We also added a lip around top solid wood planks to give it a more solid look, so of course that added to our time.
The plans were great, though we had a tough time keeping everything square. Our cabinet doors were 1 inch thick (1/2 inch door, plus 1/2 inch facade drawer fronts), and that made it almost IMPOSSIBLE to find hinges that would work with the cabinet doors. Cabinet hinges come ready to fit 3/4 inch doors OR whatever-thickness door with a 3/8 inch routed edge. So I ended up having to purchase some really heavy-duty specialized hinges from our specialty woodworking store, and those cost about $18/pair.
We're really happy with how it turned out, and it suits our needs great. See our process on my blog below.
Mon, 05/21/2012 - 09:34
Wow, you are ambitious for a first project and it came out great! Adorable, model, too, even from the back side, lol!
In reply to First project? by spiceylg
Mon, 05/21/2012 - 10:31
Yes - ambitious or foolish... one of those is the right word to describe it. But thanks! I'm happy with it and with the little model, too :).
The top was made from big box 2x12s and after an exhausting search for untreated 4x4 lumber, I decided to use reclaimed beams.
This table was a birthday gift for my 3-year old cousin. It was fun to brainstorm ideas to get it exactly the way we wanted it instead of buying one pre-made. Once we had our plans it was an easy build, done over a weekend. A full list of materials as well as step-by-step instructions can be found in the blog post linked. The top is a 20x36 pine shelf board with a 1x2 pine apron attached underneath. There are vertical support boards to hold a raised tray for supplies, and to hold the paper roll under the table. Note that the table legs are inset at one end to accommodate the paper roll. We added two magnets to the face of the table and tied two knobs (with metal washers glued on) to the underside. The paper can then be sandwiched between the magnet and the metal and won't move around while the artist is at work. It's our favorite feature! There are also magnets glued to the inside bottom of the tray to hold the buckets in place and keep them from being knocked over easily. This project was so much fun! I love having the chance to share it with you all!
I added support for more weight by adding a 2x4 on the inside of the four legs. This way, I have the entire frame supported by screws AND 2x4, so I can rest easy.
Rebecca Nemeth
My cupboard is quite a lot bigger than the one in the original post but is super sturdy.
It was a relatively easy project to build. My main issue was that I used chipboard for most of the cupboard and ironed on veneer on the cut sections which threw my door frame measurements out of whack and I had to shave a bit of my door off with a plane to get it to fit in neatly.
Sun, 08/12/2012 - 11:47
Hi there. I love this!!! I was wondering if you remembered the dimensions of wood used or what not? I want to make one or two of these for my basement laundry room for storage but am new to this so not sure how much I would increase all of the wood etc from the original plans. Thanks!
Mon, 08/13/2012 - 02:48
Hi! So glad you like it! I used SketchUp to create my dimensions to fit my space. Have you ever used it before? It's a free designing tool and really helps me to visualise if the wood's all going to fit together or not.
Here are the wood measurements I used:
Chipboard, white, 19mm
Part/Length (mm)/Width (mm)/Amount
Top:1200/436/1
Side x2:2000/400/2
Bottom shelf:1124/350 /1
Shelf x4 :1124/350/4
Frame top & bottom:1162/100 /2
Frame side x2:1800/100/2
Door frame top & bottom:476/100/2
Door frame side x2:1594/100/2
Door backing MDF 3mm
Part/Length (mm)/Width (mm)/Amount
Back:2000/1162/1
Door back:1700 /360/2
If you have any other questions, I'd be happy to help. Good luck!
Worked on this very casually and intermittently for about 3-4 weeks, though I would consider it a weekend project if you have all materials and tools necessary to complete, and a couple full days to devote to the project. With 2 young kids at home, I was only able to get an hour here and there at a time in my shop to work. I decided to leave off the top flip-down style doors, as our cable box requires line-of-sight to work, and my wife wasn't crazy about having to open those any time we were going to watch television.
I was a bit uneasy about the weight of the top, especially once the tv was placed, without any support bracing directly under the top-center piece of plywood. To add a bit of support, I added a 1x3 brace, attaching it between the tops of the 2 center legs, flush to the underside of the top. Completely hidden, and added just enough peace of mind for me to put my new tv on it, worry free.
Materials: I used maple hardwood plywood, and select grade pine for the finish/edge pieces. I found that polycarbonate sheeting was pretty expensive at my local hardware store, plus I had to special order an opaque finish, so I finished my doors with 1/4 plywood that I had left over from the back panel. I used 4 different grit levels of sandpaper (120, 220, hand sanded with 320, and then used 400 between coats of poly). Minwax Dark Walnut stain and 2 coats of clear satin polyurethane. Kreg jig is a must for a project like this, would have been lost without mine! I love that all the hinges and screws are hidden!
I'm planning to build the matching media towers from this collection next.
Modified one of the couch pieces so that the back rest only went as far as the depth of the adjacent couch; thereby making the rest of the couch a chaise. Cushions were custom made (walked into local fabric store and asked for a referral). Cushions were sliding out the back; but my build partner came up with a genius solution - used inexpensive metal threshold material and screwed it to the back seat slat. Works like a champ and looks nice too!
After collecting my tools, I needed a place to store them that would protect them. I had already had two jigsaws break because I was storing them in a rubbermaid tote. When I saw this plan I knew it was going to be perfect for my shop. My husband was supper happy because I would finally have a central spot for my workshop. My boys were happy to help when they could.
Wood Stocking Stand built by Nico