Ten Dollar Ledges
A quick shelf for a blank wall.
A quick shelf for a blank wall.
This is one of the easiest woodworking projects ever. It only took 2 cuts and 8 pocket holes.
This is by far the biggest project I've completed yet. It actually surprised me how easy it was to complete. It did take me about 4 days to build the project and an additional week to sand and paint the project.
I followed the playhouse loft plans and the storage stairs plans, adjusting only the back to allow for the additional length of the slide. I didn't add the windows to the sides (I didn't see any point in having them there). I also used the castle loft plans for the slide. When I first started this project I was planning on making the slide completely separate. I changed my mind mid project after I had the side wall cut to length at Lowe's, so I just added that small piece to the left of the slide to make up for the gap. I also made this project in 4 separate pieces (stairs, slide, front wall, back) so I could put it together in her room in one evening and not have to kick her out. Once we moved it to her room all I had to do was screw the four corners in and attach the back wall and bed slats.
I definitely recommend not using particle board. I had no idea what the difference was between particle board, mdf and plywood when I started this project. Particle board was less then half the cost of plywood, but looking back I would pay the extra for the plywood. I don't feel like the screws hold well in the particle board and it also chipped on the bottom some. I actually had a chunk come off in the corner where I must of screwed to closely to the edge. I'm sure this is basic knowledge for most, but for those newbies (like me) just a little tip.
I had a lot of fun building this bed (not so much sanding and painting) and learned a lot. Now off to browse for my next project :)
Thu, 07/09/2015 - 07:30
Awesome job! Looks clean and not even close to DIY. Keep it up!
This was a really fun project. I altered the dimensions slighly to fit my space. I also used a piece of 1/4" ply for the bottom shelf instead of thicker common board. You can keep the cost way down if you rip 2x6's into 2x2's. A single 2x2 is about $10 whereas a 2x6 is $6. You get three 2x2's out of the 2x6, so you're basically getting triple for half the cost. Pick REALLY straight 2x6's though!
Easy excellent project for That odd room you may have that needs a corner tv stand.
I use pre made 16" wide 3/4" MDF shelving from Home Depot for the Shelves, Used 1" x 3" for the top, and sprayed it all with Rustoleum Industrial flat black which dries in 15min, was the large size cans for $5.40 and and only useds 3.25 cans to paint the whole thing.
TV is a 55" Class so it actually works perfect, because the tv stand is two legs and not the typical center mounted ones. so put the tv toward the front of the console and the console is as far as you can go into the corner.
I have two power strips screwed to the back of the console, along with a cable amplifier, my wireless router for the house sits right behind the TV and you can see the blue status lights under the bottom of the TV.
Have my speaker bar in the added shelf #1 below the tv, comcast cable modem in the right side square, TIVO in the center top, DVD Player in the center bottom, and loads of extra shelf space for whatever else I can think of....
7.5' long cabinet, made with pine boards. Hardware purchased on Amazon.
My wife worked with a lady that wanted an extra tall corner hutch. She couldn't find one that would fit her requirements that was also within her budget. Naturally I got volunteered to make it since I'm pretty handy. It stands 7 feet tall. The shelving is made from birch plywood. She wanted a drawer in the middle and glass doors on top with lighting. Personally I would have chosen a lighter color but she wanted all black.
The daughter was whining (since that's what teenagers do) for a new bed(room) and a daybed was a requirement. After searching for the perfect one, we couldn't find one that worked with MY budget! When I came across these plans, I was thrilled (especially after I took a few minutes to calculate the cost)! Needless to say, I made some alterations to 1) the mattress height to accommodate the 2) trundle unit I designed. A custom ordered bedskirt (not shown) provided the perfect camouflage for the trundle and the chandelier (not shown) suspended between the center of the top rails added the perfect French touch for my daughter's dream "Paris themed" room! Thanks for the great site, can't believe I have never thought to make one myself, lol!
My 8-year-old and I built a shelf for his room, based on the Rolling Cubby Bench plans. (The paint job is all him. He originally suggested trying to paint a picture of an eagle on it, we ultimately settled on a partial flag.)
I'm fairly new to woodworking, and this was my second of four projects I've built using plans from this site so far. Cutting and assembly was just a couple of hours, but finishing stretched this out into a several-night project.
My dad and I built this table for my wife's birthday present.
I built this table for my wife as a surprise 50th birthday present. She had been wanting me to build her a farmhouse table and I loved this design. I allowed her to pick out the colors of stain/paint that she wanted for the finish after she unwrapped it. I actually went into sketchup and designed my own table, based on these plans, to fit into our smaller dining space. By designing it, I was also able to modify it to fit our chairs. The top is Oak with a red mohagany stain. The legs and aprons are pine and chalk painted in drop cloth...her favorite paint and color.
Great table. I already have people asking me to build them one.
My son needed some encouragement to keep his shoes in one place.
I made him a castle shaped shoe holder with a drawbridge door,
including an air venting back so his shoes will dry.
See link below for my youtube video of the construction...