Rustic X End Table

Submitted by Ana White on Thu, 08/15/2019 - 00:03
| Print this plan

Build your own end tables!  These gorgeous rustic style end tables are built from 2x4s and lumber.  We love the large size and the open bottom shelf. Stain or paint any color. Our beginner friendly plans make it easy with step by step diagrams, shopping list and cut list.  

Also in this Collection: Rustic X Console Table, Rustic X Coffee Table and Rustic X Bench Plans

rustic x end table plans

Rustic X Living Room Table Collection

This end table is part of a collection of living room furniture that you can build. All the plans are available for free for your use.

It all started with this beautiful X Console Table, built by Hillary from The Friendly Home.

And then we added this beautiful Rustic X Coffee Table, also built by Hillary.

Now, Hillary used up her scraps and built X End Tables!

DIY Wood Finish

Hillary used a steel wool and vinegar solution to age her end table. Want the same finish? Get the step by step tutorial here.

Pin For Later! 

Rustic X End Table

rustic x end table plans
Dimensions shown above.


Shopping List
  • 2 - 2x4 @ 8 feet long
  • 1 - 1x12 @ 3 feet long
  • 2 - 2x2 @ 8 feet long
  • 2 - 2x6 @ 8 feet long corner bracket hardware decorative bolts
  • 2 1/2" and 1 1/4" Pocket Hole screws
  • wood glue
Cut List
  • 8 - 2X4 @ 22 1/2" - Legs
  • 4 - 2X2 @ 16" - Trim
  • 2 - 1X12 @ 16" - Bottom shelf
  • 4 - 2x2 @ 13 1/4" (Longest edge, one end cut at 50 degrees off square, other end cut at 10 degrees off square, see diagram) *
  • 5 - 2x6 @ 27" - Top

*You may wish to trace and cut these in place

Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Kreg Jig
Miter Saw
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Step 1

Start by building two ends as depicted in diagrams. You can also attach with countersunk 2 1/2" screws and glue.

NOTE: Yellow board width should be 22 1/2"

Step 2

Next attach the 2x2 sides.

Step 3

And then build your bottom shelf and attach to bottom of console.

Step 4

Now it's time to fit your cross braces. A standard miter saw should cut a 50 degree angle off square. If not, you will need to mark it with a square (remember 50 degrees is off square, so that means the angle off the board edge would be 40 degrees.

Another trick is to just hold the board in place, mark the angles, and cut. These aren't support boards or anything like that, so some glue and a few nails or countersunk screws from top/bottom will do the trick.

TIP: We recommend building the entire X first, the attaching the complete X inside the end table.

Step 5

The smaller X pieces can be cut to fit.  Attach with a 1-1/2" pocket hole and 2-1/2" pocket hole screw, one screw per joint.

Step 6

Next build your top ... and attach in place with countersunk 2 1/2" screws. If you have the PH screws on hand, I just use a few of those!

Step 7

And then add the decorative hardware!

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.


Kris Taylor (not verified)

Sat, 09/15/2012 - 08:10

I have made furniture before, however the top warped.. What kind of wood are you using for this project? How do you get your projects from warping?? Any help would be great!

Hillary (not verified)

Sun, 09/23/2012 - 11:51

I've actually not had that problem unless the wood I bought was already warped. I'm pretty picky about what I bring home, especially if it is for a project that isn't meant to look rustic.

Buying the driest wood you can find will help. If it is cool to the touch and if it is especially heavy, it is still wet. Sometimes only wet wood is available, especially when you're buying 2x4s and 2x6s like for this project. Also, I think center-cut boards are supposed to warp less? Looking at the end grain to see the growth pattern can sometimes give you a clue. That would be a good thing to Google -- I know there is lots of info out there about it. Good luck!

Kris Taylor (not verified)

Tue, 10/02/2012 - 12:00

I have never used a Kreg Jig before, but I just bought one. So with good wood and the kreg.. maybe it wont warp... Thank you so much!

In reply to by Kris Taylor (not verified)


Tue, 10/02/2012 - 17:03

You will love the Kreg Jig. When I first got mine I was confused but watched a video on the Kreg site and the heavens parted. I was drilling PHs today with the jig and got to thinking how many times I have used it and asking shouldn't it be worn out? Just one point and that is to make sure your pieces are securely in place (clamped) as the pocket hole screws can produce a lot of torque and all of a sudden you are out of line. You may also experience one piece moving away from the other as you drill the screw but keep going and they will come together nice and tight. My shelf pin jig should arrive tomorrow and I can finish my version of Ana's four cubby bookshelf.

Kris Taylor (not verified)

Sat, 10/20/2012 - 19:20

Thanks so much for the tips!!! Cant wait to find time and get it started!! Thanks again!


Sun, 11/04/2012 - 17:28

I love the shape, weight of 48 lbs, size and ruggedness of this table. Built it but left off the Xs because I just could not get them right. Not yet finished so no BRAG yet. I would like to add a photo of the unfinished table here but apparently you cannot. I think I will add 2x2s to enclose the bottom shelf and add ceramic tile to the shelf. Just a thought at the moment.

A Angel (not verified)

Tue, 12/04/2012 - 07:54

How do you attach the Hex bolts?

Free Plans Made Possible By Our Sponsors