Community Brag Posts

A table that I made out of a slab of rough wood, end cut from a mill. The rounded sides of the coffee table legs were made out of round fence posts cut down the centre & placed on the sides of cedar boards. I painted my wife  & I on the legs "2 old crows". I had sufficient wood left over to build a side table.

Needed a table for our deck, but didn't want to spend the $400-500 on sets at the store. Followed the plan for the most part and it was fairly easy to build. The only thing I did differently was in building the ends was put the "X" supports in after making the "I" shape in case I was off with my cuts.

Spent an hour cutting all the pieces on a Friday night and about 3 hours assembling Saturday morning. Table was ready to eat lunch on!

-This is a gorgeous table and I am very happy with how it turned out. I could not possibly pay for the turned legs at $40 each! Even if I did, it would be worth it, as this is a piece of furniture that will last several lifetimes.

-I used very rough 2x6s for the project, so I had to do a lot of work to get them square and smooth

-I did not purchase the legs, I purchased a 8 ft piece of the best cedar Home Depot had, which actual dimensions are only 3.5x3.5, so the legs are not quite as chunky as I would have liked.

-I turned the 18" legs on a brand new mini-lathe I purchased from Harbor Freight, $150 after coupon. For the price of the legs, I chose to buy the machine and make them myself!

-I also used 1x4s for the lower shelf rather than a sheet of plywood, I felt the smooth bottom did not match the planked top. (The bottom is not done yet)

-The assembly was very straight forward and easy

-This is the first project I made it a point to stain completely PRIOR to assembly! It turned out so much better, I also glued and screwed all joints with my Kreg Jig.

It's quite a massive heavy table that will last generations, my children dance, climb, sit etc all over it and its been in use about a month now. Two coats of the poly have held up very nicely so far, and the matte finish does NOT show dirt or fingerprints, where a glossy finish would!

I used the Modern Park Bench plans. I made it a little narrower and taller to accommodate who I made it for as he is tall. I also used oak ply for the backing in order to showcase the skull art that he requested. The design was taken from his favorite shirt. Ply was ok since it is on a covered porch. Thank you Ana White for providing plans to use. Very much appreciated!

I needed a sturdy place to hang clothes in my laundry room as I took them out of the dryer. I saw the dress up center and it was perfect (just needed to be altered to fit adult clothes)

My first project, not directly from Ana White but combination of Ana White and benches I've seen on other sites.

I followed the plan directions to a "T" and it worked out so well! This projects gives me joy everytime I walk up my front steps. Thanks!

My husband completed this project in three short days.

In search of a sofa table for the sectional we found this site and plans and upgraded using wood instead of MDF and using back splash tile on the top to give a custom feel.

This was the easiest and fastest project ever! We built it out of 2x12's instead of 1x12's but i wish we had done it with 2x16's because baskets are a little hard to find in these dimensions and I would like it a little deeper. But I still love it!

When we bought the wood, we had Home Depot just make all the cuts for us. so when we got home, we just had to assemble it. It went together in about an hour {we did have to make a few adjustments because we used 2x's instead of 1x's but nothing too hard}. We decided to add some screws to the 1x4 back and side rails instead of just nails so that they would be more sturdy. We have 3 kiddos and know that they will be pulled on, walked on, ran into a lot.

The finishing took me about a day to do with lots of breaks in-between.

We stained the seat with Minwax Dark Walnut and then taped it off so that I could pain the rest white. After 3 coats of white paint, I sanded the edges and rubbed the same stain all over it. It made the edges dark and make the paint an off white. Then we put two coats of clear coat on top.

We used some scrap beadboard that we had instead of plywood. I love the finished look!!!

It cost us about $50 or less for the wood. I don't know exactly because we had a few other supplies to get there too. But it was cheap!

Almost done :)

Pretty much followed the plan, except I raised the height of the platform. I intended to make the legs longer, but I forgot and cut them to the length on the plan. It looks like the sides of the basket aren't supported as well, but the basket stays in just fine.

I also added little wings on the end to support the ends of the basket. I wanted to be able to remove the basket from the cradle without screwing it in, but also wanted the basket to be secure so I added the little wings. It was easy.

Overall a pretty easy project, except the rockers are time consuming. They're not hard to make, you just need to take your time.

I adapted the Emerson console plans pretty extensively.  I constructed the cabinet out of low grade playwood, and then clad it on all surfaces with faux painted cheap furring strip lumber of various widths. I changed the base and made it sit completely on the floor so that I would not be chasing dog fur dust bunnies that seem to accumulate under everything!  I made the open storage wider to fit my componenets and added holes to pass the wires through the back.

It was very helpful to have the plans as a jumping off point.  It takes me forever in the planning stage.  I try to figure out my dimensions to hide as many raw edges as possible in every project.  I also want to work with the widths of lumber avaialble to me since I have a fear of a tablesaw (which is still in the box after 3 years).  Give me a chop saw and a circular saw and I'm your girl!

Very proud of this project.  Thanks Ana!

I downloaded th minimalist modern nightstand plans nearly a year ago and just got around to building them last week. Actually I modified them quite a bit because I had a small space to work with and because I wanted them to follow the design theme of some of the other furnishings and features I had made for my basement renovation. In particular I changed the top and made it out of oak stair treads. I also added pop-up electrical/USB sockets as well. I really appreciate the sequencing in the plans. Though I made some dimensional and design plans, I followed the sequencing steps. It made the project much easier to complete-particularly the drawer construction and fitting. If I had done it on my own, I would probably have permanently installed the middle shelf before fitting the drawer which would have made fitting the drawer and drawer front much harder. Thanks for teaching me that.