Community Brag Posts

One of the adriondack chairs you have shared...made with wood scraps so it cost nothing only the time to make. It's comfortable and sturdy.....and I loved making it

I'm slowly working on building the whole Simple Outdoor Dining Collection.
When my Mom and I moved into our new apartment, we spent all our money on new indoor furniture, and we have this really huge porch with a nice view and nothing to put on it. So as a surprise after we moved in, I made her the bench. She loved it so much that I decided to make the matching table for her birthday. The stack-able chairs will be her Christmas present, so stay tuned for that if you'd like to see how they turn out.

-The bench was about $20 for lumber, a total of $40 or so with stain and screws and everything.

-Table was about $60 for lumber since I couldn't fit the the 12-footers in my car. I probably spent a good amount extra on a bunch of 8 footers instead. Also wasted a lot of wood that way, but I will find a use for it. Definitely get the 12 footers if at all possible. No need to buy the rest of the materials again if you have left-overs from the bench.

I didn't modify anything on this set at all, it was pretty much perfect the way it was designed. Although I did add some 1x3's to the legs on the bench to make them sturdier- notice the corner leg rather than just a 1x4 by itself. Thanks for these plans Ana, you make me look good!

So I was inspired by the Ana-While posted Farmhouse Table a few months back.. Honestly I was a little concerned about building such a large piece as my first project but I decided to invest into some common pine lumber to give it a shot. I could have bought better woodworking stock, but I was concerned I was going to mess it up anyway so I chose to stick with Home Depot / Lowes grade stock to keep the cost down.

I made a few changes from the published design:

I wanted a very large table for entertaining during the holidays. I extended the design to about 10 feet long by almost 4 feet wide.

I also am not a big fan of the seams that are left between the boards when doing butt joints using common lumber. It was a bit of work, but I trimmed off about 1/4" of material from the side of each board to make their corners square instead of the normal slightly rounded profile. With enough planing and sanding, I was able to get a reasonably tight seam with just normal garage tools.

The third design element I added was pre-drilling each of the exposed screws with a 3/4" bit about 1" deep and filling those holes with a wooden dowel. This dresses up any screws used and in my mine makes the table look a bit more traditional. Im sure some people would say just use the dowel to secure the joints, but I just wasnt that brave for an inexperienced builder.

The finish was intentionally left uneven. THere are raises and small grooves in the surface that I sanded down with 80 grit, but then only lightly went over with 150 and 220. The effect I was looking for was a surface that looked hand sawn / worked but that was still smooth to the touch and not 'dangerous' to use daily. There are some visible sanding and planing marks, but they are all soft and smooth, and help add depth and character in my opinion.

More pics available on my public facebook album: https://www.facebook.com/media/set/?set=a.10152583224649571.1073741829…

Supplies cost about $300 for lumber and finish materials. 

The face is made from 4 2x10's and 1 2x12 in the middle. 

The legs are 4x4, all other pieces are 2x4.

Tools needed to finish the table this way:

Circular saw

Table saw (to trim edges if you want tight seams)

Kreg Jig (essential for pocket holes!)

Very big clamps!   I did not have these and spent $90 or so on the 3

Hand saw

Chisel

Drill

Sander (or a LOT of patience!)

Planer (I used a cheap power planer to help level out the cheap big box lumber and to even out the joints)

STRONG sawhorses.  I broke a set of 600# rated horses re-positioning the face.   A 10ft table face is very heavy!  get help!

Finishing the table this way took a long time.  Im going to guess 60 - 80 hours went into it.  A ton of time is used getting the joining work right.  The rest of it goes together pretty quickly.

First big project. First time with the Kreg jig.  Some hidden defects but looks great in pictures!

A friend asked for a corner sink\stovetop cabinet for his tiny home . Made from sinker cypress.

Cypress Past 

I wanted a nightstand to match my farmhouse bed. I used the cheapest pine boards I could find to build this and it turned out great!

When I first built it I just used a scrap of fabric tied in a knot for the handle but added a real drawer pull when I built the matching dresser.

(sorry the pictures are crappy cell phone shots)

I followed most of the measurements with the Murphy bed with added dimensions for a full sized bed. I also added a shelf to provide support while the bed is down since I brought the platform off the floor. The table is also hinged to the bed platform so that it folds up and locks in place for a center support for the bed.

Console table!

I really like how this table turned out. This table is a beast its very heavy but very sturdy also. I used a 4x4 on the bottom so i could cut a hole out for the umbrella which worked great all I used was a spade bit for the hole.

I made this for my friend's daughter. I can't believe how easy this was to make. It is sturdy and really light weight. I put it together in one afternoon and painted it the next day.

This was my first project and I am hooked. This was an easy build. I only ran into challenges attaching the headboard and footboard to the frame because I really wanted to be able to disassemble it and reassemble just in case.. fortunately I located a website selling threaded metal inserts and I ended up just bolting it on with hex bolts. 

I was  just surprised by how fast I could build it and how long it took to finish it. Sand, wood filler, sand, caulk, prime, sand, paint, sand, paint. Get interrupted by my kids 100 times. 

Already plotting my next 3 builds..

I wanted an outdoor lounge. My partner had to work so he helped me get started and I finished it alone. He surprised me a build a corner table to complete the look.
I love it !!

This project has been modified to fit our microwave.

This coffee table was my first woodworking project ever. I followed the plans exactly but left the X off each end. They seemed a little daunting for the first time around, plus I like it without them better. Great plans and great result!

My granddaughter picked the stain color.

Fancy X table and bench

First project made from scratch....took me a while but glad it is finished! Will try to do one more of a larger size for my other dog.