mamas shelves
Made these shelves for my mom.
Made these shelves for my mom.
I wanted to build as big of a booshelf as I feasibly could so I altered the sizings in width and height to create this monster. The planks in the back did not fit perfectly in the new sizing so I spaced them a little bit and I think it turned out nice. The spacing gives it more of barn-like look to it. I also alternated stains on the planking between American Walnut and Dark Walnut because this thing took more than a can of stain and I thought the look was neat. The majority of the piece is in American walnut which turned out a little redder than I hoped, but overall I am happy how this turned out.
As always, thanks for the plans!
Mon, 07/27/2015 - 17:09
You did a great job on this bookshelf! Love the plank back and the barn-like look it gives, and the alternating colors for the back. Looks beautiful!
In reply to Great bookshelf! by JoanneS
Tue, 07/28/2015 - 07:39
Thanks! Always good to hear you are not the only one that loves your piece after all the blood, sweat and tears :)
Wed, 11/02/2016 - 00:14
Hello, would you be able to provide the exact measurements you used to build this beautiful piece? It would make my life a whole lot easier lol Thank you :)
Thu, 01/19/2017 - 10:29
Final dimmensions of the bookshelf ended up being 51"W x 16.5"D x 81.5"H. I would suggest measuring out the space where you would like to put the shelf and see how much room you have.
Love this site! I've made the Facny X Farm Table, and now this piece. I changed the back to ship lap. Also cut out the baseboard so it sits up against the drywall then coped the baseboard around the base to look built in. Thanks!!!
Edit - sorry for the pics being sideways, they're not like that on my phone or computer :(
This took about 10 hours, including prime and paint. I raised the side rails 3 1/2 inches to dado the posts to accept a 2x4 siderail on the inside of the post, with 1x8 covering it at the center of the post. The siderails are bolted with 4x5/16" bolts, washers and nuts. We chose to leave it more rustic, showing the siderails at the ends and the bolt holes. It is all pine, bought new and along with a 1" forstner bit to recess the bolts, cost $198. It can be repainted at any time. Tools I used were a compound saw for ease of cutting straight cuts, a cordless and corded drill, 1/2" socket and box wrench, easy square and a circular saw for the 1x8's. We painted it with left over paint. Because its pine, we primed with BIN,
Sun, 06/05/2011 - 20:23
It is 1x5 bead board (pine). Some places call it match board. It is v-groove, tongue and groove and has a smooth (flat) side and a two inch flat, bead, two inch flat side. The plans called for a 61" wide panel but I made it 58" with the dadoed posts (1 1/2 inch each cut).
If you want to do the panel using the T&G bead board, make sure to lay your 1x4's out the distance of what ever height you want your panels and center the first piece of T&G bead board on both the top and bottom panel. Then you work your way out fitting the T&G and screwing in each piece. When you come to the two end pieces, they are going to ned to be ripped but by starting at center, they will be even at the end when ripped.
Another tip is when screwing the panel, you will want to get at least halfway into the 3 1/2" post. measure the distance you want to cut on the drill bit and put a piece of tape on the bit. Then drill until you get to the tape.
Modified from Ana's Home Depot DIY, using all pine lumber w/1x6 for the arms.
Sat, 05/03/2014 - 19:40
Actual plans for this loveseat/bench are not showing unfortunately :(
I love this site! I used the Modular Office- Narrow Open File Base under an old 5 panel door added some old table legs and voila new desk for two!
I thought the perfect thing to go above the desk was the $10 ledge shelf. I actually had the wood and the stain already...so this project was basically free...just my time.
Super easy build, had to make a few adjusments because of the size of the room. My daughter absolutely loves it. Thanks Ana White for these awesome plans!!
Thanks Ana for the plans. A new bench / bookshelves for our daughter's bedroom.
I stumbled upon the octagon picinic table almost by mistake. I set out to just find a blueprint for a standard picnic table to know how much materials I needed and this came up in the top of the Google search. As soon as I saw it I knew it would be perfect for my backyard. It looks great and the neighbors are quiet jealous!
In the first additional photo you will also see the entry way bench and storage shelf (http://ana-white.com/2009/11/plans-for-entry-storage-benchshelf_2314.ht…) that I worked on when I wanted a break from the table.
I loved the Reclaimed Wood Night Stand so much that I needed a dresser to match. Virtually the same just added a single drawer height and widened.
Fri, 08/07/2015 - 11:12
I am looking to build something exactly like this, can you share plans or any suggestions, thanks!
Hi Ana! Thank you so much for creating all these wonderful woodworking plans. My wife and I wanted a garden bench, and I thought it would be so much more fun to make one than to buy one, so voila! Couldn't have done it without your plans. I made a couple modifications to make it more "Adirondack" style, with the paisley-shaped armrests and curved backpiece. Great plans, thrilled with how easy they were to follow and how well the bench came out!
Thanks -
Bruce
Made your tall planter. Love all your builds
Combined the modular office small desktop with the Narrow file drawer base unit to suit my needs/space requirements. Used the legs from the narrow farmhouse table because I just loved them! Added beadboard for the drawer faces because it matches the rest of our house.
Mon, 04/28/2014 - 22:18
I am about to start on a very similar 4 draw version of this, do you have any more information? In particular I was wondering how the drawer slides were fitted - are the side or bottom fitting? Cheers and well done!
Converted an ordinary bathroom vanity into a Napoleon sink console/vanity. This is the second one I’ve completed, the first was in the hall bathroom which Hubby calls “his” bathroom. Since this one for the master bath is more feminine, I’m calling her Josephine! This was approximately a day and a half project, but spread out over several weekends. I had originally planned to put a faux drawer in front of the sink, and had the drawer front made, but then decided I’d like to try to make some custom drawers in front of the sink to utilize that space. I ended up doing the center drawer fronts twice – on the first try the space in the center was a little too narrow for the knob once the trim was in place. Since the vanity is in a corner, the sink doesn’t fall exactly in the center of the vanity cabinet, leaving it left of center by about an inch. This required different middle drawer sizes with interesting shapes.
The drawers are made from a combination of 3/8” craft boards and 3/8” plywood, ½” craft board, and some ¼” plywood for the bottoms (all of them except the one right of center – that has ¾” plywood for the bottom). The 2 outer drawers also have ¾” S4S as guides.
The doors and drawer fronts are ¼” birch plywood cut to size, with ½” x 1 ½” craft boards glued to the fronts for rails and stiles (I added a few pin nails from the back side also). Inside these, mitered pieces of mini-stop moulding were glued in place. The whole thing received some putty on the edges and joints, and thorough sanding with 80-grit, then 220-grit.
The inside frames are made from S4S, 1x2, and some scraps of 1x4 cut to size. If I were doing this in a newly constructed vanity without the sink already in place, the setup for the drawers would have been much simpler. But, we weren’t ready to buy new yet, so necessity was the mother of invention and we have this. I re-used the hinges and 2 of the knobs from the original, and I bought 4 more and the hardware for the drawers.
The pull-outs in the bottom are made from plywood scraps, thoroughly sanded and painted. These are based on Ana’s wood pull out cabinet drawer organizer, with added supports across the bottom to make the drawer clear the lip of the face frame, keeping them the correct distance apart, and giving something to attach to the cabinet floor.
For the inside floor of the cabinet, I got this Idea from Yvonne at Sunnyside Up-Stairs in this post:
http://sunnysideup-stairs.blogspot.com/2013/06/progress-installed-dishw…
Left over flooring was placed on the cabinet floor to give it a fresh new look and protect the cabinet bottom. Our house is 21 years old, so you can imagine the floor of the vanity cabinet had seen some wear and tear. Now it looks new!
Sun, 07/28/2013 - 12:25
I love your vanity. Something about it helps me imagine a British nobleman's home, or since she is Josephine, I suppose it would be in the home of a French duchess. =D I really do like the idea of having that pull out drawer on the bottom of the vanity.
I am definitely going to give glazing and distressing a try sometime. I just have to find the right project for the look. Lest I forget, thank you for sharing the link to my site. :)
Sun, 07/28/2013 - 15:57
Thank you so much for the nice comments! I love the idea of a Duchess, I think I'll nickname this finish Duchess Blue! :) I was happy to share your blog link, the idea about the vinyl flooring in the vanity worked like a charm, I'm going to do that in my kitchen and the other bathrooms too.
Followed the plan exactly, with the exception of the stain. I mixed a walnut and rosewood stain to give it a little more warmth/red.
Here is a custom rustic barn wood dog crate we built for our friends – with the majority of the barn wood reclaimed from their own barn. The piece is approximately 36″ high, 60″ wide, and 29″ deep; with interior dimensions of 30″ x 56″ x 26″ – plenty of room for a large dog to move around and stretch out. Of course, it is on locking casters too so it can be easily moved around.
The frame of this piece is made from the reclaimed barn wood, which was 2 x 6 stock resawn down to 2 x 3. The sliding barn door also started as 2 x 6 material which we cut down to 1 x 2 stock. The barn door was the only piece of this where we used a Kreg jig and pocket hole screws. The rest of this custom rustic barn wood dog crate used miter joints for the front corner, while the back and bottom were attached in rabbets we cut in the outer frame.
The spindles are standard 1/2″ rebar, cut to the appropriate length and painted with a hammered black spray paint. They are are recessed about 1″ into the wooden frame to ensure the dog can’t push them out or crack the wood while leaning on them.
This custom rustic barn wood dog crate also includes custom, hand made barn door hardware we made ourselves. Yes, we do some metal work too! We made this barn door hardware from standard flat bar steel and pulley wheels. We even made custom clevis pins from 5/8″ steel rod to hold the wheels in place.
Barn Door Console by David!
My first non-home-repair project. Made three of the sling chairs for my kids. They each picked out their own fabric (regular fabric). We still have not sanded, filled and painted but are hoping to do so this weekend. The kids were very excited to have them. I have been reading your website for months now wishing I had time to make something, and these chairs fit the bill. Thank you!
I built matching side tables using Ana's Narrow Cottage End Table plan. I changed the height to suit the arms of my furniture. They fit our tight space and look fantastic with our existing wood pieces. Very easy to build, even the drawers! I used a router to finish the edge on the drawers, to make them stand out a little more. I learned to put my pocket holes on the outside of the drawer, since the back one is in the back, and the front one is covered by the separate drawer front piece. A Kreg jig makes this a very simple project. Also, I sanded my boards before assembly, then did touch-ups before finishing the project.
We had some additional kids coming over and I needed to build them quickly.
From a pine tree in the back yard to a great looking crib that will hopefully stay in the family for generations.
We had to take down a pine in the back yard to make room for a barn so I had it milled into lumber for future projects. I was able to get the majority of the lumber I needed from that tree, everything except for the 4x4's and 2x6's. I got what I thought was pine but after staining it I quickly realized that it was not (maybe hemlock?). The grain didnt match at all so I had to track down some new wood and remake the pieces. Boy was that frustrating! I also bothered myself to hide as many fasteners from (finished) view as possible. It made the project a bit more involved but the finished product made it all worth it.