Community Brag Posts

We took the rustic x console table plan and made it half the length and a bit narrower for the unity table at my daughters wedding. It is made of white pine 2x4's, white pine 2x10's for the top and the shelves are 3/4 pine plywood.It is stained minwax red mahogany and finished with 3 coats of ace brand gloss polyurethane. Lydia is using it for the TV in their apartment.Total cost was less than $25 so this was a bargain console.It only took a few hours to build and stain it. Due to the heat in Arkansas the finish was a chore . It dried too fast and had runs so I had to sand alot. It looked kinda rustic after I sanded so I just put 2 more coats on and eveyone loves it.

Slightly modified in size so that it would better fit our wall. Really simple and fairly fast to complete. Wife LOVES it :)

Love this simple peice! 

We decided to just make the headboard, king size.

This nightstand was my fourth build, and it was so much fun! All of the measurements listed were accurate and it was super easy to build! Doing my second one right now!

I needed something for my tv that would be high enough to accommodate our 18 inch sound bar sub so I modified the Taylor's Console plan to fit. Love the way it looks with my plank wall! Pretty happy with the first piece of furniture I built!

We had to adjust the center hutch a bit to fit the beds into the room, but we are very very pleased with how this turned out.  Thanks for the plans!

Recently identified this wonderful website. Thank you for the plan and really enjoying the process of building the furniture from scratch.

This outdoor set is a mix of the vintage bar stool plans and the simple table and bench set. I added a few things here and there.

Loving our new table - we ended up spending about $100 since we used for 4x4s than 2x4s. We also left out the 2 center pieces since we shorted the table to 6ft.

I used the corner bookcase plan.  It was easy to follow.  I think it turned out well for my 2nd wood project. My sister had the idea of painting the panels blue to match the buildin bookcases in my libray room.  I have the backs of them painted navy blue.

My Version of your Country 'X' Desk, Thank you for your website & videos, Joe from Canada

I'm so excited about my farmhouse table! I used mostly scrap wood that I had lying around, and I adjusted the length of the table to fit my space (it is 62" long). I cut the table ends in a curve pattern just for a little more interest. I used the steel wool/vinegar solution to darken and age the top, with a paste wax finish on top to give it a more aged patina. I painted the base with the paint leftover from my outdoor sectional that I built from Ana's plans. The actual table didn't take long to put together, but it took me a month to get around to the finish.

Sorry for the photos - I used my cell phone camera and the light was bad!

In order to make this island a little beafier I used 4x4 wood for the X as well as the the top and bottom braces. Top is made up of glued up 1x3 maple wood. It looked really good raw, but decided to stain it to give a more uniform look. I bought the rustic handles and the bottle opener on Amazon.com. I used lag bolts and washers for the finishing accents...similar to the pottery barn island. Painted them with Rustoleum oil bronzed paint and then dabbed it with a paper towel to give it a rougher finish to it and then sprayed the casters as well. This was a fun project and are getting a lot of use out of it. Thanks goes to Anna for the plans and inspiration for this island. Rich

Sliding barn door console 

Used Ana's plans to build my floor to ceiling shiplap fireplace. Excellent guide made it easy.

I made this vintage step stool awhile ago but forgot to post it to the Brag board. At first I made it then put a coat of a mix of beeswax and olive oil that I mixed up. But then it was being used in the bathroom by the kids and got filthy. So I sanded it down and put a coat of stain and poly on it. I love it much more now!

Very easy plan and great for a beginner project.

With Father's Day rolling in, my sons and I needed a gift, stat! My husband thinks that Table Tennis is the quintessential father-son activity, so that was an obvious choice.
We needed something easy to make, easy to store, and budget friendly. With a 6, 4, and 2 year old helping out, I made a foldable mdf ping pong table that could easily be placed on our picnic table outside.
We had home depot cut the mdf in half, primed it, taped off some lines, spray painted it with chalkboard paint (bonus, you can keep score!), and screwed 4 small hinges to attach the 2 halves. We added a removable table tennis net, some paddles and balls, and have played nearly every day!