Community Brag Posts

I made this set for my granddaughter using the Fancy Doll Crib plans. On this build I enlarged the size of the Fancy doll crib to be closer to the Olivia crib. For anyone interested: ends-13 5/8”; bottom-21¾”; side rails 21”; legs-20”; 12- 3/8” dowels @ 8¼”. I thought the scale of the finials from Lowe’s were too large, so I found some I liked better at Hobby Lobby: 3 pcs per pack @ $1.47, item #165274. Since I got 6 altogether, I put two on the high chair. Love the look. I also changed the shape of the curve of the ends and replicated that on the highchair back. The shape of the highchair tray is also curved and slightly cantilevered over the side ends; the tray is 4¾” x 13” to allow for the curve, cut from a 6” wide length of scrap. The vintage lamb theme that I used with my great-nieces is carried out with this set, too. I found the water-slip decals at www.decalcottage.com.

This table was made using the original farmhouse table plans with pocket holes.I tapered the two inside sides of the 4x4s (25%) and subtracted the bottom support structure. All pieces were glued and screwed using the kreg system. Even without the lower support this table is rock solid. I choose to make this table look a little more traditional then the farmhouse table to match our design plans.

All parts of the table were sanded down smooth to 180 grit and treated with minwax prestain wood conditioner. The table was then stained with cabot premium wood stain and sealer in one(espresso -satin). Warning large surfaces are hard to stain evenly with out brush marks using this product. I used 3 coats in all with a light sanding using 600 grit after the first coat since it is a water based stain. It covered just a little more of the natural wood grain then I would have liked but I did prefer it to the polyshades product I used on the custom bench behind it.

When using pine it maybe best to just go for the distressed look. I am worried that my smooth table top will get destroyed by my son but he knows he isn't allowed to play cars on the table now so I am crossing my fingers. So far the table top is holding up very nicely to any abuse but it is still early on in its life.

I think in the future I will bite the bullet and use hard woods. As long as it takes to build furniture its nice if it lasts a little longer.

We made the table with modifications to extend it from 72 inches to 96 inches. We created breadboard table ends. 

Purchased a moses basket for my 1st grandchild and wanted to build the rocking cradle, there were not alot of plans online that i liked for this project. So after a few mock ups i was ready to go, but the rocking cradle continued to progress during the build , adding the diaperbag shelf between the rockers and then added extra support under where the moses basket sits. Overall was a fun project , and cant wait to see it get some use.

I needed an end table that was a little bigger than the average end table - I had a space to fill in a corner between a couch and chair and was tired of the blank space being used as a dumping ground for...things my kids didn't want to put away or throw away. :) So I pulled ideas from a couple projects here and came up this. The cost was free since I just used the leftover wood from other projects we'd done and paint we already had lying around.

I fell in love with this table and decided to tackle it as my first ever furniture build. We spent more money that we'd planned investing in some new tools (i.e. Kreg Jig Mini and Clamps). We also had a lot of anxiety about initially getting started and trying the Kreg Jig for the first time, but I watched Ana's Kreg Jig Tutorial on Youtube, and it was actually very easy.

I'm going to say that it took us 10-20 hours to complete, because of the way we finished the table. We only worked on it 1-2 hours each week though, so it took us a couple months. :-)

This table is now on our patio where we can use it for toy storage or as a serving buffet for BBQ's. I'd call it a success! Thanks Ana for the inspiration!

For this project, I wanted my faux fireplace to look very similar to a real fireplace (of course!). So in orde to do that, I added a little more depth by using 1x6 boards instead of 1x3s. For the front of the piece, I added the faux brick wall paneling from Home Depot and used the spackling method to give it that weathered appearance!! 

Now storing 5 bikes in the shed instead of hanging from the ceiling in the garage.

This is a king sized bed frame. The beams interlock. They were burnt with a torch, stained and clear coated. The headboard was my first attempt at upholstery.

I made this a built-in cabinet instead of freestanding. I am so in love with how it turned out. My 15 year old daughter helped me build it, and we couldn't be happier. The total cost for this was around $300. The wood itself was only $200, but my drill died on me, so I had to get a new one. (Poor me, right?)

This new built-in has changed the whole look of my dining room. I just wish I had done this a year ago!

The plans seemed ok for me. I used all scrap lumber I had laying around. I bought a kreg jig in the middle of this project, after watching one of Ana's vidoes's about pocket holes. That is one reason why I built the 3 doors all twice, but also swapped out the top piece of the bin 3x's before I finally settled. In other words, I really struggled with this, but I was so excited to perservere and have this completed!  

I haven't wanted to make one of these for a long time. Thank you so much for the site and all the plans! I love all your work and your style. 

This small but elegant side table was made based upon a plan from The Design Confidential. A friend of mine gave me a lot of 3/4" solid oak flooring that her deceased husband (11 years ago) had stored in a shed. It is beautiful. So I made this little table using the wood for the top. I made the top by putting Tightbond III glue in the flooring grooves and then clamping the pieces together. Then after the glue dried I used my flooring saw to rip the tongues and grooves so I have one solid piece of flooring/top. I also did not glue the top to the base but just used pocket hole screws from the underside to hold it on the base. The reason was in case the top or base became damaged it would be easily removable for repair.

This table was a lot of fun to make it wasn't too hard. The hardest part was cutting the dados. If you have a table saw, it's not as hard. I hope you watch the video of how it was made.
http://youtu.be/ymz3Zim79Lo?list=PLRGcaQeW9svX5lRtTc9w2LrOzEFoez3j0

Great plans!!  We modified just a little. Thank you!

My working area is 7 square metre, so I had to think how to get the most in it. I found Anas working bench and made me my own bench.

This doll crib is for another grandniece who loves both her baby boy and girl dolls, hence the Jack and Jill decal. This bed is modified from the Fancy Doll Crib plans using 1 x 2 for the side rails instead of dowels, and also a flat top. It is also larger than the plans: 21" long and 20" legs. My sister found a vintage J & J fabric piece which we plan to use as the mattress cover.

I said this is a day project but it takes me several days in between other activities, and I am very slow and methodical. (I also make sure to fill in all of the pocket holes with wood filler, usually two "coats" to get them perfectly level with the surrounding wood. After painting, it's very hard to tell where the fasteners are unless you know where to look.) It would take most people much less time than I. This is my 5th doll bed, and I have at least one more to go.

Simple/Fun project

Build Instructions:
http://www.instructables.com/id/Solar-Birdhouse/

Video of the build:
https://www.youtube.com/watch?v=SU5ffvweSjQ

I wanted a corner kitchen table.  I used the farm house table plans and made up the bench!