Community Brag Posts

This project was one that I've been planning for about 18 months- I had to wait until we moved back into our home to start the build, so I had plenty of time to think about how to maximize my storage space in this small room with a slanted ceiling. My husband had some time off from work and offered to watch our toddler during the day time- so that was all the motivation I needed to start this big build!

Overall, it took about a week from beginning to end. The cost was between $400-$500 for everything- including hardware, paint, supplies etc. Still a huge savings over what it would have cost us to purchase desk and storage units to work in this room (I priced them out at about $2000-$2500 - WAAAAY out of our price range).

For the main desk unit I used the plans for the reclaimed look wood bedside table. I modified the height of the legs to 28" tall so that the sewing desk height was correct for when I'm sitting at my machine for hours on end. I also modified one of the units to be an open shelving unit, so that I could store my patterns and misc. sewing notions in baskets on the shelves.

The desk top was created by using six 1 x 4 whitewood boards joined with pocket holes. The corner joint is "woven" in a sense to give a unique look to the unit. I used 4 brackets in the corner (secured to the studs) to support the weight of the corner of the desk. I used Dark Walnut stain and then followed up with 3 coats of Poly (sanding in between each coat).

The two fabric/machine storage bins were made using the cubby bookcase plans as a base. Both plans were modified to maximize fabric storage with the small space- hence no face frame on each unit. The middle storage unit is one that was my first build a few years back, before I'd even heard of knock off wood- oh how it would have been so much easier if I'd known about this site back then. I added a plywood top with a piano hinge to fold out for a stand up cutting unit. For the legs, I simply went to the table/baluster aisle at my local hardware store and purchase some hardware to secure two balusters to the plywood top. Screwed them in on the outside of the window frame so I don't have to unscrew the legs every time I fold it up and away, cut the balusters down to the proper height and that was done!

The ribbon/wrapping paper storage was super easy- just used some of my left over 2 x 2 furring strips, along with 14 dowel rods and 1 /14 screw in hooks. I pre-drilled the holes for the screw in hooks as well as the 3" screws I used to mount it to the wall.

The thread holder was a previous build of mine as well- just cut out LOTS of dowels that fit into the peg board and glued them in place. Added a little decorative trim to finish it, and painted it white.

Overall I could not be more excited about how this build turned out...aside from wood working, sewing is my next favorite thing (I have a small Etsy shop and do local craft fairs for fun). Having the stand up cutting station is a HUGE relief, as after 10 or so years in the Army, my knees and back are shot (who would have ever thought that jumping out of airplanes wasn't good for you!) The fabric storage is great and allows me to see all of my different fabrics so I eliminate over-buying (which I obviously have a problem with) and purchasing doubles.

I can't thank Ana enough for her website- I grew up with a dad that builds everything, but was always a bit intimidated when it came to building stuff for myself. Her plans really break everything down to the simplest level of instruction and make the building process stress free. This was my first time building a cabinet unit and I was very worried about the drawers not working, but I just followed along on the instructions and they came out perfect.

Sandbox with built in seats

Needed a small workbench to fit in a tight space, but still wanted something sturdy as it supports a 1-ton arbor press. Your plans were so helpful!

Here's a small tutorial on how to add simple metal accents to furniture. We used something as simple as door knobs at your local home improvement store to make it happen!

Check out the tutorial here http://sawgrasshome.com/?p=1443

I came across the Shanty Sideboard plan while looking around the site. I decided to make this my first build from the site. I modified it slightly by making overlay doors instead of inset. I found that this allowed me more room for adjustments to the doors to get the best look. I used Pure-Bond Birch Hardwood Plywood from Home Depot for the main build with Select Pine from Lowes as the trim. This was all put together using Kreg Pocket Holes and 1 1/4 inch screws.

I used Luane Plywood as the backing for the doors. I then finished it by painting it with an off-white from Olympic (at Lowes). I left the Luane plywood in its natural state. The doors were mounted with Blum style Face-Frame cabinet hinges. I then applied several coats of Water Based Ultimate Polyurethane from Rustoleum.

I have included a picture of the sideboard in the unfinished and finished state.

I will soon be building a Hutch to go one top. I will use the Shanty Hutch Plan as the basis and modify it from there.

----------------------------------------------

I recently completed the hutch for the sideboard. I used the Shanty Hutch plan as the beginning point and then modified it quite a bit. I made three sections and added drawers at the bottom of each section.

I then used the same Luane Plywood to make the backing. This brings it all together.

The total cost was around $550.00 and worth every penny. Much better than spending $3,000.00 at store.

I based the side pieces on Ana's plan's measurements, but I was inspired by a different baby gym I had seen to make the top piece look like clouds. I also wanted the pieces to be able to disassemble. Instead of screwing the three pieces together, I cut notches with a band saw (could also use a jigsaw) so that they would fit together but still feel sturdy. I recommend drilling the toy holes close to the bottom edge so that this is compatible with store-bought toys.

Using Ana's Cassidy bed plans, I made this king sized bed. I substituted scrap pieces for them shims.

This is my very first wood working project! I know its not perfect and I learned from my mistakes. I found a miter saw at a garage sale and after three hours of plugging it in and unplugging it, I finally worked up the courage to make it make a noise! Then I eventually worked up the courage to cut wood lol! I'm pretty proud of myself for building something and I am going to continue practicing until I can make really cool stuff!

We have been slowly updating our sunroom and making it a play area for our kids. I built this trestle play table and a couple of rolling cubes to go with it. I still need seating for two more (for playdates and when the grown-ups want to sit) so I'm trying to decide what to do on the other side.

I wanted to use all wood that we already had in the garage, so the top is made from 1x12s connected with pocket holes, and the legs are 2x6s.

In the background you can see the board & batten my husband and I installed a few weeks ago. We also ripped out some moldy carpeting, sanded the concrete and laid vinyl plank flooring. It's coming along!

Plan for the rolling storage cubes: http://www.shanty-2-chic.com/2012/07/rolling-storage-cube-stools.html

My own take on a mirrored console

I needed a larger kitchen table to seat six and made the trestle table. Love it!

Terri M

This is the second project I have made from this website, which I LOVE! I needed some sort of table to use with a large sectional sofa because I refused to give up my huge ottoman for a coffee table! This is perfect. I loved the brag post with the shelf added so I used that idea also.

When it came to decoration, I used some apple barrel craft paint and found some scrapbook paper I really liked. This was my first use of modge podge so it was not as flawless as I hoped but I still think it turned out well. And best of all it will be used often!

FYI - by saving money on the particleboard shelf, I ended up spending a lot of time applying wood filler.

Instead of using 1x3's for the legs we used two 2x4's for the outside legs and then used 1x4's for the fillers. We also used 1x4's for the ladder. We will be adding shelving against the wall and we have a desk top that has been painted with dry erase surface which will give it a whole new dynamic. Project one of many is done :)

I did modify a bit with the length and width. I also left the supports vertical instead angling them. Love how my table came out!

Directly from plan. Fun to make. Kreg and glue attachements.

This site features the queen size version of this headboard, I decided to build the King and use more elaborate molding pieces, which increased the cost. I stained the wood to a very close match although my mobile photos don't do justice to this claim. It took me about a week to complete with nights and weekend availability.

Storage box made from left over 1 by 4 and plywood from recent projects and a top I made for another cabinet but didn't use.  All I bought was two 1 by 4s for the top trim and the hinges.