Community Brag Posts

Great project with super clear instructions!  Love the look of the sawhorse legs and had just completed a live edge table top, so merged the two for this coffee table.  

The craft table was based on the Modern Craft Table plans and heavily modified to be at regular seating height. We also added a pull-out iron table based on plans from Made by Marzipan. The pictures are kinda deceiving, but the ironing table does push all the way back in the table and it only juts out just to show it :) Check out our blog post for more:

http://tonyandkristine.blogspot.com/2013/03/diy-craft-table.html

DIY Craft Desk.

I built this desk for my wife to give her more space to create her crafts. I meshed a couple designs that I had researched to give her a unique design. This project took me 1 week to complete by only working on it in the evenings but it could be done faster if you have more time available than I did!  

Materials Needed:
2 - 6 foot 1x4" pine or Poplar wood
1- 8 foot 1x4 pine or Poplar wood
4- 2x2" pine wood 29" long
2- 1x2" pine wood 24" long
1- 12"x48" pine board (pre cut craft wood in Lowe's)
1- 24"x 72" pine board (pre cut craft wood in Lowe's)
Box of 1 1/2" wood screws
Wood glue

Wood stain and/or paint 
8- 1" corner braces

1). Cut the 12"x48" craft board in half (2- 12"x24"boards.)This will be your shelves. Sand all of the wood prior to staining.
2.) Stain shelves and desk top. We used two coats of gray stain. Finish with one coat of Polyacrylic. Sand. Then one more coat of polyacrylic.
3.) Cut the 1"x2" trim to 2- 24" long strips.
4.) Attach the 2x2" posts to the 1x2" trim with wood glue and wood screws. You will end up with an upside down U shape. This trim piece will give added support for desk top. Do this twice and then Paint your posts.
5.) Mark where you want your shelves on the posts and screw in your corner braces to hold the shelves up. I placed the shelf inside the posts to give me 12" of width for baskets. Screw your braces onto your shelf and then attach to the posts. I recommend doing the bottom shelf first so it stabilizes the posts.
6.) Do the same thing with the top shelf. Mark where you want them and attach with corner braces.
7.) Moving on to the cross box base.... Build the 4 sides of the box first with the 1"x4" boards. This desk is 24" deep and 29" tall. Use wood glue and wood screws to assemble. I predrilled the holes then, placed glue on then screwed together.
8.) Make sure your top 1x4" is the full depth of the desk so the weight of the desk top is spread evenly on box.
9.) I used this guide for the interior cross pieces. http://sawdustgirl.com/x-leg-office-desk/#aa
10.) Paint your cross base.
11.) Attach desk top to bases with wood glue and wood screws and you are all set!

It was a fun project! - Jen

I found the plans for this bed on this site and was sooooo happy. i was looking for a unique bed for my daughter. I had searched beds for girls and cam across castle beds. I found some pretty extravagant beds costing $20,000 by personal designers and then I found beds from $1,000 to $5,000 buy it and put it together and THEN I found this plan. People asked me if I had experience in building anything. The answer was no BUT I CAN do it!. Plus the plans were very easy to read and understand! My daughter is beyond excited! She can hardly contain herself! THANK YOU!

Our kids love our new library!  We have lots of books but few places to store them (one grandma is a reading teacher and the other works in a library).

Our alcove is 11' wide and the long shelves are 10' long.  The short shelves are 2' long.  The antique church pew in the center is 5' wide.  I put the bottom shelves just below the outlets so we have an iPad charging station.

I built this project 8x10 and made the back wall exactly like the front wall and just added diy windows for air circulation. I live in the desert so I did not use clear panels I used white panels for sides and top and tinted panels for front and back so that my plants would not get scorched. I am running a hydroponic system and could not be happier with the results for a first time gardener! I built it completely by myself in about a month, I do have a full time job and kids that need to be taken to practice and lessons after school.

Well...this was pretty much all done by me.

I am really not liking how many bad boards there are at the store. It takes forever to find a decent board. I had some of my x12s measuring closer to 11 (yes I know they aren't 12 inches).

The door is a little wonky but if it bothers me too much I will just replace it with a curtain on a tension rod.

I love the yellow and I am very proud of myself :)

I didn't have a Kreg jig (too expensive for us right now) but it would definitely have been helpful...

I built this before my son was born to use as a changing table in his room.  I used leftover plywood from another project which made it a cheap build.  It is super sturdy and has plenty of storage on the top to hold wipes, diapers, and creams.  I used shelf lining and bought cute baskets to complete the look.