Community Brag Posts

Modified clubhouse bed

My daughter wanted to remodel her room with a peacock farm theme. These plans worked perfectly. I decided to just enclose the bottom, add 3 drawers and a barn door to give it functionality and add to the "farm" theme. Enclosing the bottom mad for way more storage in her room. I'm going to add a cubby on the head board side. It's going to mimic a "lean to" shead to further add to the rustic farm look.

Built from Plan(s)
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
None
Recommended Skill Level
Intermediate

Toddler bed

Submitted by Anonymous (not verified) on Wed, 10/23/2019 - 09:35

Built this classic bed for my grandson. It was one of the easiest builds yet. All of Ana White's plans are super user friendly.

Built from Plan(s)
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
Minwax, dark walnut stain, polyurethane
Recommended Skill Level
Beginner

Comments

Outdoor Sectional

Submitted by Boogiemy on Tue, 02/28/2012 - 05:54

We built this sectional for approximately $700. The wood and supplies cost about $200. The cushions were the most expensive, about $500. We wanted 24 inch wide and 5 inch thick cushions that were well made. I ended up ordering them online from Wal-Mart. The project could have taken about one day, but due to work and kids, it took us about a week.

Estimated Cost
$700
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
Cabot Australian Timber oil in honey teak
Recommended Skill Level
Beginner

Comments

Corona Coffee Table

I first saw this table on the Shanty 2 Chic website and when I saw that it was based on a plan from Ana, I knew we had to build it. I asked my husband David to get started on it right away.

It turned out perfectly!!!

Built from Plan(s)
Estimated Cost
250
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
To finish the table, we started with Minwax Pre-Stain Conditioner, and followed it with Minwax Golden Pecan, Minwax in Golden Oak and finally Minwax Polyacrylic.
Recommended Skill Level
Intermediate

Rustic Entryway Table

Submitted by LN2014 on Mon, 03/14/2016 - 22:54

Made from Canadian white pine just made from 2x6s that where ripped down to the top,legs, sides and the X's. Sanded 3/4in plywood was used for both shelves instead of solid 1x12 pine board to cut down on cost of the build. 15in wide x 4ft long x 30in high

Estimated Cost
$50
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Varathane Ash Stain
Varathane Polyurethane Satin
Recommended Skill Level
Intermediate

Comments

Treehouse bed

Submitted by Anonymous (not verified) on Mon, 10/28/2019 - 14:19

Completed this for my grand daughter. Only extra I added was handle and step made from metal pipe. She just loves it. Looks perfect in her birch forest. 🙂

Estimated Cost
300.00

Dresser

I originally wanted the Hudson Dresser from Pottery Barn but I wanted it a little more feminine. I also really liked the Madison Dresser plans posted on this website so I combined the two and this is what I got. It took me a weekend to build and a week to stain (a layer of stain after work a day). I got the drawer pulls from World Market and I got the bunn feet on ebay. I'm overall very pleased with it.

Built from Plan(s)
Estimated Cost
$225
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Polyshades 2-in-1 Bombay Mahogany (three coats with sanding with 220 grit sandpaper in between coats)
Recommended Skill Level
Intermediate

Comments

debandtom25

Thu, 03/08/2012 - 10:03

I need to redo my whole living room and I want to have a nice piece to put the TV on top. I LOVE the feet and drawers of this piece and I might just have to steal some inspiration.

Mario Castle Bunk

Submitted by jlholmes80 on Wed, 01/01/2014 - 00:30

So my son needed a bunk bed and we came upon the sweet pea bed. It was too girly for him so we decided to go with a theme that would be timeless, something he wouldn't mind having when he is 18 (or older, he is 10 now). What is better than Mario! (We are a house full of gamers, my 17 year old is super jealous of this bed lol). The build was fairly easy and the plans were straight forward enough, the time consuming part was the painting (without all the painting we could have probably build this in a long weekend). We changed a few things, like not arching the top windows, adding the 4 inch 2x4 squares to the top to give the castle look and stairs are made to look like stairs from the side so we stepped out the banister instead of angling it.

Estimated Cost
500
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Paint colors were all Behr paint+ primer (mostly eggshell or flat):
New Brick, Black, Polar Bear White, Green Crush, Green Acres, Lemon Zest, Windjammer, and French Silver. Some of the colors (like pinkish tone on the stairs) we created on our own mixing the New Brick and the Polar Bear.

Polyurethane. I mixed regular oil based polyurethane (gloss) with mineral spirits (50/50) and wiped it on. It was remarkably simple and gave it a nice seal/finish. Last coat I used Satin Polyurethane because I didn't want the gloss finish. I opted not to sand between coats because this is a kids bed and I wasn't looking for that "perfect" finish, just wanted some added protection.
Recommended Skill Level
Intermediate

Comments

Mrswhetstone1

Wed, 01/01/2014 - 06:11

This is the coolest bed I have ever seen! I wish I could make this for my youngest. I could probably build it, but I 'm pretty sure it would go downhill when I started painting it. You did an amazing job and your son is a very lucky boy!

jlholmes80

Wed, 01/01/2014 - 16:10

You can totally do it! I am a horrible painter (I'm too impatient) and you can't tell with this because of how forgiving the design ends up being. There is so much going on it's hard to pinpoint the mistakes. :)

jlholmes80

Wed, 01/01/2014 - 16:07

Thanks so much! This was the first thing we ever built (although my husband did a lot of building stuff in his youth we have never done anything together and I was a total beginner) so we are very happy with it. :D I appreciate all the kind words.

amercpina

Fri, 05/03/2019 - 22:00

We are super excited to build this for our 9 year old son. To make this a Full size bed am I correct in thinking that I only need to alter the side panels by adding 15inches? I am paranoid about building it and the mattress not fitting. Thanks so much!

Stackable child-sized chairs

Chairs are hard.... when you don't use plans. 

I used Ana's plans for round 2 of these chairs. I actually feared for my children's safety with the first set I made using no plans at all. With plans in hand, these turned out excellent and were actually quite easy to build. 

I used 1x2s for the legs, 1x3s for the side supports and for the turquoise back panel, a 1x4 for the pink back panel, and scrap MDF board for the seat base. 

I regret using the MDF board, it chips easily. In hindsight, I should have used 1x3s for the seat bottom. 

Estimated Cost
$20
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
White cabinet paint, pink and turquoise spray paint
Recommended Skill Level
Beginner

Entry/Console Table

Submitted by Robinwood on Mon, 03/05/2012 - 22:35

A friend needed an entry table, so I went with the Cheap and Easy Console plan and found the baskets at Ross. I modified to include lower shelf and did a single board top because I was trying to avoid buying more wood.

Estimated Time Investment
Afternoon Project (3-6 Hours)
Recommended Skill Level
Beginner

Baby boy misunderstands the concept of the 'Man Crate'

Submitted by aclohesy on Thu, 01/02/2014 - 08:43

Men come in crates - who knew?

My crate is a gift for a friend, to be filled with manly foodstuffs, but in the mean time, the little 'un loved trying it out.

I didn't follow the plans rigidly, but I absolutely loved the idea and was inspired by all the great photos on this site. Mine looks the same from above and below, but the front and back side slats are attached to the lid while the left and right ones are attached to the box. Also, everything uses the same 18mm ply (what I had available!) which means you can easily lift it using the side slats, but lift the lid off with the front and back slats.

Enjoyed this project - will more than likely make others in the future. Maybe even spend a bit of time on the finish next time - the 'rough 'n' ready' look works well enough for this kind of project though, so it plays to my strengths!

Built from Plan(s)
Estimated Cost
15 GBP (approx 25 USD)
Estimated Time Investment
An Hour or Two (0-2 Hours)
Finish Used
None on the wood. Briefly sanded, but no power tools used other than drill driver.

'Man Crate' lettering added with a sharpie and a template.
Recommended Skill Level
Beginner

Comments

JoanneS

Thu, 01/02/2014 - 11:04

Your man crate looks great! You can definitely say your little guy has "man tested" it as well! (super cute pictures with him, by the way) The idea of using the top side trims for handles is super! Thanks for sharing this build! :)
Joanne

BeaxBuilt

Tue, 02/04/2014 - 21:37

I love the boy :) I love this idea too. Will have to build it for my dads next gift.

Handmade by Frank

Submitted by Anonymous (not verified) on Sun, 03/20/2016 - 14:31

Handmade by Frank. He saw a pic on CL and figured it out without any plans.

Recommended Skill Level
Intermediate

Comments

Twin Loft Beds for Twins

Submitted by annierey on Thu, 10/31/2019 - 16:33

My twins just turned four and were still sleeping in their toddler beds, so it was time for an upgrade.  They still want to share a room so we knew we needed to maximize space and open up some room for them to play.  We chose the Camp Loft Bed but raised the height to 72" (with 53" of headspace) so we might be able to add a desk underneath when they get older. 

Essentially, we made two loft beds with the platforms but omitted the stairs.  Then we built a slightly lower platform to put between the two beds, which acts as a step down.  Then instead of making stairs that jut out into the room, we added two 2x4s as ladder rungs to the lower platform.  This also acts as a tunnel for the twins to crawl under to go between each other's play spaces.   This also makes it so the beds can be easily separated if we ever need to put them in separate rooms. 

When it was complete we noticed one of the beds was a little wobbly, so we added diagonal braces in the corners and another 2x4 across the length of the bottom to help stabilize it.  We also chose to use 1x4 pieces of pine as the slats for the mattress to lay across, but they didn't feel like they would support our weight if we wanted to read to them in bed.  So we added two more 2x4s underneath the slats the entire length of the bed, which has added a ton of support. 

We stopped keeping track of exactly how much it cost, but it was close to $400 for both beds combined.  And it took most of my husband's free time for two weeks, but most of that was painting two coats of paint on every piece before assembling.  First he cut all the pieces to size, drilled the holes with a Kreg Jig, and then painted.  To make the painting more efficient, he put a bunch of screws into boards so he could paint all the exposed sides of the lumber, flip, and leave them to dry.  Then we assembled the beds in their room. 

The twins love their new beds, and we love how much more space they have to play in their room!  We were worried the room would feel too crowded but with the openness of the plan and the space that was opened up underneath, we think it turned out great!  Now we can move in a bunch of their toys and reclaim some of our house!  Thanks for the great plans!

Estimated Cost
$400
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Two coats of white paint/primer
Recommended Skill Level
Beginner

Console entry table

Submitted by Anonymous (not verified) on Thu, 07/20/2023 - 12:07

This entry table I made from wood I got from a recycle center of wood products. It’s been in our entry now for several years. I have only basic tools-no planers and jointers, etc. I do have a fold up table saw that I use once in awhile. I enjoy working with natural /live edge and or construction grade materials. Always impressed with the items Ana has built. Good job Ana😁👍

Built from Plan(s)

Toddler Canopy Bed

I designed and built this canopy bed without knowing Ana had already done a toddler canopy bed! Talk about reinventing the wheel. I should have known she already had plans up. ;)

Full plans are on my site, but I thought I'd add this as a brag post instead of a project plan since Ana's plans are already here. They're different, but the end result is very similar!

Built from Plan(s)
Estimated Cost
$20-50 depending on paint and finish supplies on hand
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Zinsser water-based primer, semi-gloss latex paint, and polycrilic topcoat.
Recommended Skill Level
Beginner

Modern Dining Table

Our extra long living/dining room was just begging for a little definition. So I scoured all of Ana White's plans for some inspiration for the perfect-for-us table. I have never built anything, so I enlisted the help of my genius dad and we got to work!

We ended up using elements of the Modern Outdoor Patio Table and the Farmhouse Table. We sized the patio table down to six feet long and used the board layout from the farmhouse table for the table top. We also changed up the table legs a bit to add some visual interest.

After tackling the table, we built the banquette and beadboard wall. I never thought I would learn so much about power tools. Ha! This project was so much fun. Thank you for the free plans!! I can't wait to work on our next project!

You can read more about our table here: ‎ http://www.becomingwhitney.com/dining-area-progress/
here: http://www.becomingwhitney.com/it-is-finished/
and here: http://www.becomingwhitney.com/christmas-cheerin-it-up/

Estimated Cost
$200
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
I sanded this baby within an inch of its life. I chose not to use a wood conditioner because I wanted a rough look, and I adored the unevenness of the stain in some areas. I put on one heavy coat of Minwax Espresso stain with a rag. I used a teeny paintbrush to get the legs and between the planks of the table. Then I sealed it with a semi-gloss water-based poly. I put five coats on the table top and sides and three coats on the legs. It gave it a great finish, but isn't too shiny in person.
Recommended Skill Level
Intermediate

Comments

Linda7

Tue, 01/07/2014 - 10:15

The fabulous thing about DIY is how you can modify a plan to suit your needs. You and your dad have built a one-of-a-kind that can be handed down to future generations. Love the style and finish. Keep up the good work!

Whitney Gothra

Tue, 01/14/2014 - 08:37

Thank you, Linda! That is one of my favorite aspects of DIY - the options are unlimited!

6 x 6 Sandbox

Submitted by Anonymous (not verified) on Wed, 03/23/2016 - 20:54

This was our first attempt at making a woodworking project but knew it had to be done to save our plants from our son digging in them. It took us all weekend (mostly because of the staining) but we completed the project in 2 days. We went a little bigger (made a 6 x 6 box) to give our son some room and allow for friends. I loved putting the project together and look forward to many years of use from this box. Thank you for such simple plans!

Built from Plan(s)
Estimated Time Investment
Weekend Project (10-20 Hours)
Recommended Skill Level
Beginner

Farmhouse Twin Bed

Loved building this for my daughter. The plans were simple to follow and everything came together easily. So happy with how it turned out. Thank you, Ana!

Built from Plan(s)
Estimated Cost
$125
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
Behr Bright White, semi-gloss
Caulk for most joint boards