Community Brag Posts

This was a big project to tackle. I'm not very good at modifying building plans, so my husband was frustrated during the beginning of this build. But we are very happy with the way it turned out.
The hardest part of the build was the steps. We modified them to look like blocks, so getting the dimensions equal was tough. We also made it a full size bed so that there was more room under the bed.
We used plexiglass for the doors and LED lighting under the bed.

After 3 years staring at the empty space beneath my dining room window, I decided it was time for a buffet end table. I went to Pintrist for some ideas and found this awesome design by Ana White.

I decided to modify the dimensions and do a multi-stain pattern to give the table a more bohemian look.

Here's a link to the step by step instructions:
http://rusticcedar.blogspot.com

I've had this idea to build some sort of storage bench or blanket chest for quite a while now. I knew I wanted a classic look with detailed moldings and a solid wood top.

I have plans for this build avaliable HERE. 

You can check out my detailed video tutorial :

Two projects that I recently built for my wife and my daughter. My wife wanted a tea bar and a beach vibe, my daughter wanted an outdoor couch so it is made out of cedar. They both loved them.

Todd Springer

My first attempt at woodworking

Using the 4x4 Truss Bench plan (http://ana-white.com/2013/10/plans/4x4-truss-benches), we built this bench using entirely reclaimed lumber. (We had removed an old patio and part of a fence.) We already had all of the lumber, screws, etc. so the only cost to us for this project was the cost of the stain.

We modified the plan slightly, using 2x4s on the ends.

My husband is obsessed with decking screws. Thus the entire bench is held together with 2 1/2 inch decking screws. (Unfortunately, we purchased our Kreg Jig a day following the completion of this project.)

Because the lumber was very old and weathered, there is a lot of character to the wood. There were some incredibly soft spots which made sanding a challenge, and some of the boards were somewhat warped. However, we still really like the way it turned out.

I sanded (and sanded and sanded) using 60 grit, then 80... then 120... then 220. I filled the screw holes with wood filler (and sanded again). I then conditioned the wood with Minwax pre-stain wood conditioner. I used Minwax Early American oil based stain on the entire project. I then went over the top only with Minwax Weathered Oak. After about 36 hours of drying time, I used 2 coats of Minwax Fast-Drying clear semi-gloss polyurethane.

This bench is a beast! I'm sure it weighs over 75 pounds. It is extremely solid, and quite beautiful in our dining room. The plans were easy to follow, and the whole thing went together fairly quickly. (It would have been completed even more quickly had we had our Kreg Jig at the time. Lesson learned.)

I loved he Hannah canopy bed for my daughter but felt like it was missing something. I decided to tuft the headboard and I used rhinestone buttons to give it that girly look with a small pop of glam. The tufting took probably 12 hours in total but totally worth it. We then followed all the instructions on how to build the bed with the exception of having any screws go in through the sides of the fabric on the headboard. We used plates to hold the headboard in place and screwed around the edges. It was time consuming but we love how it came together.

Farmhouse Table with pocket holes.

Duffsdesignsnc

To build:
2 x 4s
1 1/4" dowel rods - x3
2 1/2" wood screws screws
1 1/2" PVC pipe (for spacers) - cut at 3/8" thick - x2

Needed:
Hole saw kit
powerful 3/8" drill or 1/2" drill
Jig saw
Miter saw
sandpaper
wood filler
paint

Was a great project! Was surprisingly easy to put this together. Modified the plans slightly and used all 1x3" boards for the edges (instead of 1x2"). Made the top out of left over walnut from the truss farmhouse table we made earlier in the month. Painted off-white (fledgling). Highly recommend buying decorative hinges as it made a big difference in the look.

Ana Whites site is always my first stop for inspiration, she always has good designs and diagrams. I usually use her plans as a rough guide, and then tweak them as needed.

For this table, I made it 42" square, and adjusted the height. 

The main difference is I built this from PT pine, and cedar as this is going to be an outdoor table, and I would like it to last.  I painted the frame with 3 coats of exterior semi gloss paint, and used Helmsman spar urethane for the top. I did not stain the wood, as I love the color variations of natural cedar.

I also used galvanized carriage bolts to connect the legs. This increased the costt, but I wanted to be able to remove the legs.  For more in depth connection details see my blog.

The table turned out quite well, is very sturdy and has gotten quite a few compliments, thanks Ana for the inspiration to build cool stuf! I love building STUFF!

Finally have a lawn chair that won't blow away in the MatSu Valley wind.

This was my first attempt at building and I learned a lot such as if you drop pine, it cracks in half - and - when cutting with a jigsaw, cut inside the lines....you can always trim more off, but you can't put it back - and - my dogs can distress a piece of furniture faster than I can if I put it under "thier" window....whether I want them to or not!
This was a great beginner project and gives a fast, satisfying result. As you can see, it has become the cat's bench...can't get a picture of it without him, he lives on it!
Just a couple of notes: I cut the legs more according to the plan diagram than the pretty cuts Patrick made on his...I wasn't ready for that. Also, I didn't have my glasses outside with me, so my measurements on the legs are probably not right. I made the top shorter because I wanted it for a specific space (which didn't work out, see note about about dogs and distressing....ugh!).
Also, this probably should have taken me just an hour or so, but I had my Kreg jig set all wrong and first had shallow pocket holes (see note above about pine breaking when dropped) and then made them too deep (learned to use wood filler)! That's when I finally got my butt into the house to get my glasses to read the dang directions (again!).
Thanks Patrick and Ana for giving me such a great, easy beginner project!

This project started on a Saturday and I moved it into the house the following Friday. All that being done with two little cherubs running around and making demands of me every 10 minutes. Super easy build and my first time.

This was one of my first builds ever! I'm hooked! 

We built our patio furniture with your outdoor chair and couch plans! Thank you thank you! 

Candice