Community Brag Posts

This is one of the easiest woodworking projects ever. It only took 2 cuts and 8 pocket holes.

I built 4 chairs total. A set for my mother and another for my mother-in-law for Mothers Day. The first set I built are the green ones with the cushions. The second set are the stanined chairs. The second set went a little easier than the first because I learned from my mistakes. What I did differently on the second set was mainly to sand and stain before assembling. I had a hard time getting in between all of the nooks on the painted chairs. I ended up using my paint sprayer to paint them because it was just going to take forever otherwise. The side table was very easy and straightforward. No issues there. All in all a pretty easy project. Both moms were very pleased with their gift! Thank you Ana and Home Depot once again for the awesome plans!!

There was some deviation from the original plans..  We made the storage boxes a bit taller and the headboard has several new features.

First off, the under-bed storage takes up the whole size of the bed.  So the drawers (six of them) are nice and deep.  One of the drawers is actually the dog's bed now.

The picture doesn't show it but behind the headboard there are cubbies for storing books, tablets, phones, glasses, etc.

On both sides of the headboard there are four electrical outlets plus two USB charging outlets for charging tablets, phones, etc.

There are two reading lamps on the headboard as well.

I did the construction portion while my talented wife did the amazing paint job.

My first project from Ana's website! I figured in order to make more furniture I'm going to need a sturdy work bench to help me along the way. I cut my legs at 36" instead of 33". The 3 added inches brings it to a standard kitchen countertop height (I think, at least mine is). Thanks for the inspiration and plan pericles49!

This was a great way to keep my five year old daughter busy on a rainy afternoon. I had a scrap piece of 1x4 and bought some clothes pins and 10 cents clearance wooden figures at Joann. We also used some left over acrylic paint and some glitter nail polish. Thanks for a other great idea Ana!

I did add slats to the back as well as the sides as you can see in the photos. This was to hold the cushions in place and make sure they didn't fall out. Worked out very well. The 5 additional verticle slats were 11 1/4 inches and required no further purchase as they were made from the scraps. I also added the additional horizontal slat on the sides using 5/8 decking board left over from building the deck. The sides measured 25 1/2 to fit inside the arm and was 1 1/2 inches from the inside of the couch. I simply screwd them in from the front and back. The rear horizontal piece measures 75 inches and create additional support for the back cushoins, which in this case I used 17x17 inch pillows. I simply screwed this piece into the rear verticle slats. I finished all of it off with a 1/16 roundover bit with my router to make "soft" edges. All-in-all I think that the small changes made for a very polished looking and stout piece of outdoor furniture! 

Thanks Anna white for the Shoe bench  plans!

The daughter was whining (since that's what teenagers do) for a new bed(room) and a daybed was a requirement. After searching for the perfect one, we couldn't find one that worked with MY budget! When I came across these plans, I was thrilled (especially after I took a few minutes to calculate the cost)! Needless to say, I made some alterations to 1) the mattress height to accommodate the 2) trundle unit I designed. A custom ordered bedskirt (not shown) provided the perfect camouflage for the trundle and the chandelier (not shown) suspended between the center of the top rails added the perfect French touch for my daughter's dream "Paris themed" room! Thanks for the great site, can't believe I have never thought to make one myself, lol!

My 8-year-old and I built a shelf for his room, based on the Rolling Cubby Bench plans. (The paint job is all him. He originally suggested trying to paint a picture of an eagle on it, we ultimately settled on a partial flag.)

I'm fairly new to woodworking, and this was my second of four projects I've built using plans from this site so far. Cutting and assembly was just a couple of hours, but finishing stretched this out into a several-night project.

My father-in-law built this for me using Anna White's plans. He tweeked a few things to add somethings I wanted to add. A huge sheet of white board bought from Lowes was used to make both easel sides and the shelves. Once he had it built for me, I painted the lilac paint color onto the wood and whiteboard shelves. The black chalk board side was made by using black chalboard paint. I wanted it to look cute so, I added a black boarder on the white board, and then used a cotton ball with the lilac paint to make the paint blotch style on both sides. I cannot wait to use this in my classroom!

I'm building a doll bunk bed from Ana's plans later on for a friend's daughter.  I figured that since I had all the materials to do the linens, I would get that finished now.  I used the plans from Ana's 18" doll mattress instructions and created these two sets of beds - they're "sisters" but not twins, since I ran out of materials to make 2 quilts.  Since it's going to one recipient, I figure she won't mind having 1 quilt and 1 blanket that coordinate.  The mattresses were SUPER easy to put together, and I opted to keep them plain without buttons, in case I want to make fitted sheets at another time.  Took me about 10 minutes to make each mattress.

I loved these little ledges, especially since I had the perfect scraps for them. I needed a little extra storage in our story-time corner, and these were perfect. Took me one nap time to get them cut, assembled and painted! SWEET!!!!

I am in the process of remodeling/redecorating my tiny house. I started with the kitchen and am now moving into the living room. The two rooms are connected so I needed something that would match the "beachy feel without being obvious" style I am trying to accomplish. I also needed a place for my files, printer, etc since I don't have an office. My house is very small so I have to consider function in every piece of furniture I own. This table was the PERFECT solution! It hides my seldom used but definitely necessary office supplies while looking super cute and brightening up the room.

As you can see I made a few slight changes to the look of the trundle. I made it look like three "drawers" instead of the two in the plans, and used manila rope instead of handles or cutting out the shape in Ana's design. I also lined the inside of the trundle with felt to protect my computer, etc. from the hard surface of the wood. I couldn't help pick my favorite color, since you can't see it while the trundle is closed. Though not pictured here, I added a bracket for files as well (they didn't photograph well). I picked it up from a woodworking specialty store for $15.

All in all it was an easy second project for me, I had it built and nearly finished in a weekend.

I had no experience building furniture prior to this project but I wanted a 12 ft outdoor table and could not find one.  This tables center section is 8 ft and was built roughly following the plans for the farmhouse table.  I added two 2 ft extensions at each end making the overall table 12 ft.  The extensions included aprons so when installed they look to be part of the table.  The extensions just plug into the end apron of the center section with 2x4 oak braces which engage in the apron and under the table approximately 2 ft from end.  There is no visual sagging of the extensions. I finished the table with Sikkens DEK finish.

I needed a new desk and found some plans on Ana's website.Made a little modification to it for a little more work space. Turned out great I thought. Had never used pocket holes before, I think I'm hooked now.

When we moved into our home we had minimal furniture pieces. On a tight budget and not wanting to buy something that was made of veneer, I stumbled upon the attractive and functional plans for the cube shelves. I love that I can "add on" to the set with additional pieces if I want to in the future. But for now, one set of cube shelving is just right for us.

This was the first project that I used the table saw by myself, and while it went just fine I do think it would have been helpful to have another set of hands around. Piecing together the first two joints was a bit challenging with only one set of hands holding the wood and putting in nails. But once I got a few done, the piece really came together quickly. It literally took me just a few hours to cut the pieces and put it together. It's the sanding painting and priming that can take some time and patience!

This was my third or fourth project and it was pretty tough. I started out with the basic build which was pretty simple and then I got to the end where everything was built except for the drawer slides and boy was it rough. I think that i spend half of the time on this project doing the drawer slides and half the time doing the build and the finish. I don't want to discourage anyone from doing this project but make sure you don't get in over your head. Check out my profile I am willing to do builds for people for an inexpensive price.

http://ana-white.com/users/daddydrew