Community Brag Posts

My second project from hungary!

First stab at this table turned out so well a friend bought it off me and I had to build a second.

sofa table made from console plan, I just changed the measurements.

We built this over the course of a couple of weekends. I think the key thing was making sure my 1x6's were the correct width before we began to cut all the other boards. There was a lot of trimming after the fact making the overall width 1/2" shorter than the plans. Some adjustments made to the original plans were...

1) Using decking brackets to support the plywood to the 1x8s on the trundle (super easy way to secure it)

2) Purchased side rail brackets exactly like the ones here from my local woodworking shop.

This makes the bed easy to disassemble because although I swear I'll never move again I'm not building the bed into the room.

3) Instead of casters on the bottom we used those plastic furniture sliders.  They were way cheaper and so slim. With the weight of the trundle wood and mattress they move flawlessly.

4) Since my daughter has a memory foam bed I was worried about sagging. We used small 1x? ripped in half along the inside of the side rails for a little lip and then 4 1x6's the width of the mattress to make supports and then laid plywood on top of that. 5) Cut down the headboard by 6.5" so that the mattress butted up against it.

Me personally I hate when there is a gap there for pillows to fall down in the middle of the night.

This is a pretty easy project and makes a nice holiday gift. This version was made from a scrap piece of hardwood and a 5/8" dowel. As an extra touch, I added a compartment inside the board to store the pieces. The compartment panel is held on with magnets for a clean look.

The quick video shows how the compartment works.

https://youtu.be/jEzhipj-BjA

This was my first Wood Project - EVER.

Working with this plan was quite easy. I just changed the design of the table top to my wife´s wish. I used "Golden Oak Stain" for the Legs and "Provincial Stain" for the Table top and Bench. The Legs are covered with Water seal and the Tops with 3 layers of Polyurethane. Chairs are Stained in Provincial also. Was a lot of fun for all of us. Learned a lot during this build.

Thanks

This has probably been done before but here it is for consideration by my fellow woodworkers. If you're anything like me I get pretty impatient waiting for wood glue to work its way out of the tube. So using some scrap wood, I drilled 1.5 inch holes in a small 1x4 board and elevated it about 3 inches. A small board under the glue tubes catches any unwanted drips. Makes a perfect caddy for my glue tubes and no more waiting for my glue. Its always ready to go!

I sent these plans to my dad and said I wanted him to help me build it for Christmas. He came with everything cut and ready to be sanded and assembled! It was put together and stained in a day! I love my Christmas present, and love that my dad and I built it. It will be a family table, for sure! 

This was my first bigger woodworking project, and I loved the project and the plan! I'm just starting out buying tools, so the only power tool I used for this was a drill. I also have yet to get a work bench, so for now I was just working on the floor inside my apartment.
In order to use up some leftover wood, I made the sides out of several boards instead of one solid piece. I didn't use pocket holes for lack of a jig; instead I simply glued the boards on the sides and connected them with a few thin screwed-on boards inside. I will still line the inside with some sort of cloth, so I wasn't too concerned about what it looks like inside.
Considering my circumstances, I'm extremely pleased with the results, and ready to soon move on to another project.
From start to finish it took me about 3 weeks of working on it about 2 hours in the evening maybe 4 days a week (mind you, I'm a beginner and was using hand tools).

I found the Workbench Console plans on this site and thought it would look great behind the sofa.

The length was extended to make it comfortable for 3 people to sit at and also to span the length of the sofa. I cut out a section at the back and lowered it to hold some glasses. This fits 4 beer glasses, 4 wine glasses and 4 shot glasses. The towel holder is a cast iron key that I found on Amazon. On the other end is a cast iron bottle opener found on eBay.

I would like to take credit for the chairs, but I cheated and got these from IKEA.

We love using this while eating dinner and watching a movie and is especially handy when guests are over.

Made this Accessory Holder as a Christmas gift for a male cousin to hold his phone, watch, ring, glasses, and wallet.  Comes apart for easy movement.  I like the two-tone of the stains and the simplicity of the holder.  Router kept giving a bit of kickback, biting into the wood where it was unwanted, hence the messy cord line, but as with most of my projects, I don't mind the mistakes that make them more "unique".  Artistic choice?  : )  Also difficult was figuring out the angle to cut the opening slot for the side piece.  It needed to be angled to set the side piece just how I wanted it.  Eventually decided on 10 degrees.  
The idea for this holder was based on this: http://cleverwoodprojects.org/woodworking-projects-for-beginners-six-ea…

Don't read the site- it was clearly written by a bot or ESL individual, because it's mostly gibberish.  Just used the image for inspiration.

I freehanded a design that then was drawn on the wood and had plenty of fittings and mockup pieces made throughout to figure out how things would fit.  Fun challenge, great gift. 

We've made the decision to homeschool our almost 5 year old daughter starting in September. The dining room will be the school room, but I don't want to lose my table in the process. So I began looking for good storage options. I saw the Display-It-Storage Mirror on the PB Teen website and loved it! Right up until I choked on the price tag. I went inspiration hunting and found Ana's Willy bookcase plans. I modified the Highrise Condo Willy bookcase, added a base with lazy susan hardware and a top outfitted with crown molding. Then I bought some cork on Amazon to create a cork board on one side, a role of dry erase paper to create a dry erase board on the other side and framed them. On the back, I hung a bathroom organizer with lots of pockets for dry erase pens, push pins, pencils, tape, scissors, etc. Finishing touch was my daughter's choice of scrapbook paper for the inside backing.

Anna, thanks for your project! I only strengthened it a metal plate in the center, extended sitting on 4" and feet connected bolts.