Community Brag Posts

Followed the plans, with minor modifications to adapt the size to the available wood. Bigger modifications are the use of bolts and nuts instead of screws (to allow easier disassembling for storing), and the underneath reinforcements to avoid the table to bend over time.

Thanks for the plans, the kids loved it!

Gonzalo, from Portugal

Great picnic table by Steve White

Since I had little space in my floor I took to logs from the field.
I first polished them with sandpaper and steelwool. 1st time dry, 2nd time wet. After drying I paintetd one with white stain. The other one with nutchest stain and clear coat.

The white log was once more polished with steelwool after painting.
Therefore it has an used/bleached look.

I added warderobe hooks to each log and screwed them to the wall.

Price 30 €

About 10 € for 20 € for the hooks and screws.

Sorry, my english is not so good - I'm not a native speaker.

I converted the plans to king size and used oak for the headboard and the platform edge on the bed. The oak added to the cost as it is almost 10x the cost as construction lumber.
I made the headboard frame with pocket holes and attached it to the plywood with screws from behind. I also used pocket screws to assemble the bed frame.

I made two of these...one for each daughter.

I am enamored by the Simple Outdoor Table that is usually featured on the homepage. This was my second project, and in hindsight, I it took several weeks to finish working at night because I made several mistakes that required some problem solving. Naively, though, I studied the plans, borrowed a saw and got to work.

I opted for two benches to save space on the patio when not in use. As you can see in the picture of the bench tops, I opted for a smaller spacer (1/16")because it improved the looks dramatically, but that left me with a gap. There will be a skinny slat in the middle of each bench.

I also opted for 3/16" spacers on the tabletop which required one more board than was scripted. That is much easier to account for on the table then the benches.

You can see from the stacks of lumber in the garage, assembling is the easy part! I hope to never see the words, sand, stain, and seal in sequence again. I also learned a few difficult lessons when it came to using the Kreg Jig, which was new to me.

Now that it's done, though, I am very proud of the outcome.

I enjoy making birdhouses and log cabin style is my favorite. I make the logs by setting my saw to rip 3/4 pine at 3/4 so I have 3/4 square strips. I then decide the size of my birdhouse and cut the logs accordingly. I also "wittle" on them a little to make it look more authentic. I simply then just stack, glue and nail one row at a time. You can use 1/4 poplar for the roof but I ripped pine at 1/16 and cut shakes with my utility knife and glue them on one at a time (there are 104 on this roof).

I had a friend make a request for a console table.  We came up with this design to fit her space and needs.  It was a pretty easy build.

Built the entertainment center for our new home. Thanks for the great plans.

This is my new couch ,that I built with my husbands help,I could not find a one piece cushion in my area but, I did manage to find individual cushion.I am no expert , but I am learning as I go.

I had my seed starters sitting on a TV stand by my sunny window, which was as ugly as it gets (see before photo...). So, I built this little console for my gardening stuff to sit on while my seedlings are growing. It turned out being the perfect size for what I'm using it for. I only modified it slightly, by adding end pieces to the top (just subtracted 6'' from the length of the top pieces and measured the width of the top to decide the length of the end pieces. I also used pocket holes to attach my bottom shelf pieces and the top shelf pieces, instead of nails. I've never done a 2 tone piece (I love the look of stained wood) so I was nervous about painting over the wood...but I'm really really happy with how it turned out! It was easy to make, and mine was done in an afternoon. Thanks Ana!!

Build Instructions:
http://www.instructables.com/id/Shelves-for-a-Shed/

I looked at purchasing brackets but I couldn’t get the exact size and the price seemed high for something so simple – plus I had a few excess 2×4s from the last job. Mainly, I wanted to utilize the area in the upper portion of the shed while keeping the floor clear for yard/garden equipment. There are multiple variations of this style bracket online. I took a little different approach by utilizing the existing part of the shed (top plate) for support. I don’t know the load capacity but I’m quite sure it will handle any of the items (tarps, paint cans, etc.) I plan to place on the shelf.

My wife saw this project on your page. I had to shorten it to two feet, but, it pretty easy to do and turned out pretty well 👍🏼😁

Steve Phethean
 

My husband built this for one of the recruiters in his station for his retirement from the Army after 20 yrs of service.

I've been looking for a way to hide my ugly garbage can in my kitchen for a while now.  I figured it would cost way too much to buy something like this and was so excited to find Ana's plans online.  This was my first furniture attempt ever.  The plans provided made the entire process so easy.  I used some leftover beadboard for the door and some odds and ends we had laying around for the hardware to keep the costs down.  

Simple but beautiful!

I needed 3 stools for my kids to eat breakfast at the counter. These were perfect.

I already owned the fabric so I only needed to purchase the wood and the foam. I made it entirely out of furring strips so it was really inexpensive.

I took me a couple of hours to build and sand all 3.

Thanks for sharing this plan, I served to use a round glass tha I have saved,