Community Brag Posts

We have built things before, but this is our first from Ana's Site. We just finished this over a month ago... Was so much fun to do and I just love how it turned out! I decided not to paint just yet, so the buyer can decide. I have just primed it. I learned how to use a kreg jig, and bought a very cheap one... Best tool ever. There are no screws visible at all. I think if I did it again I would do something different with the handle.. not sure what though. It was difficult to make it look right. Thank goodness for the patience of my husband.

Made an adirondack chair from ana's plan. I am from the UK, but i still made it the plan as much as I could without resorting to mm's

We needed a bookcase to fill a void in our living room and this was it. I altered the dimensions to increase the height to 72.5". I also added crown molding to the top which turned out nice. I used the same Bombay mahogany stain suggested by a previous post.

I started on the Farmhouse bed and as I got further into it I decided it needed a bit of 'extra' attention, hence the dentil moulding across the top and the panels to cover the 1x6's used for the headboard and the foot board, they are finished off with some cove moulding.

I used Spax bolts on the side supports and used a Forstner bit to drill down far enough to hide the bolts and made some wooden plugs to cover the holes. Minwax Special Walnut in the finish.

Hope you like it

This 8ft dining table and bench was created with inspiration from Ana White (with a few modifications). It was made with all scrap wood except the table top. Full details of the table build (and kitchen remodel) can be found at www.chasingadreamblog.wordpress.com.

I built this table and two simple benches, inspired by the farmhouse table plans. I modified the plan slightly, in that I didn't add the center 2x4 on the bottom, or the two 2x4's between the legs. I also added a second "bread end board," and customized the corners with some "L" bracket accessories. It took me a week to build everything, then add the finish. It would have gone quicker, had I had time to do it all at the same time, but I had to make time after work to do everything. All, in all, this is probably a weekend job, at most. 

I loved Ana's upholstered toy box benches that she made and really wanted to do some of my own (three girls = muchos toys). We are remodeling our kitchen, so I decided to use our old cabinets for as much of this project as I could! Fun to keep a little bit of our home with us wherever we move (military family). :)

This planter was easy to make. The only thing I would have done differently is to have stained and applied the weather coating before I assembled it so that the weather coating got into the cracks better. But overall, I love how it turned out! I think it would've taken only an afternoon to do if it hadn't been so hot outside which slowed me down.

First time actually following a plan and not making it up as I go along! Turned out pretty nice :-)

This table was inspired by the pocket screw table. only I did not use pocket screws. it is constructed using loose tenon construction and dowels. Notice the middle stretcher  and the wooden nut and bolt that holds it together

I needed a project, my daughter and son-in-law wanted a cabinet that had to be custom built to fit in their small space. It was just what I needed. Nothing simple for my 1st time, oh, no! I wanted doors and drawers. Learned a lot, and know I have a lot more to learn. The importance of getting things square is probably #1 on my list. I thought I'd start parking my car in the garage, but this was too much fun - the tools are staying!

I did this table in 8 hours and I am ready to do some other projects. The final goal is to do the all house.

Hooray! I recently finished building a dining room bench. For this project, I used the Providence Bench plans by Ana White. I started this project in May, and two months later it is finally complete! I am really happy with how the bench turned out! It is pretty sturdy and makes for a nice addition to the dining room!

This was a really fun project. I altered the dimensions slighly to fit my space. I also used a piece of 1/4" ply for the bottom shelf instead of thicker common board. You can keep the cost way down if you rip 2x6's into 2x2's. A single 2x2 is about $10 whereas a 2x6 is $6. You get three 2x2's out of the 2x6, so you're basically getting triple for half the cost. Pick REALLY straight 2x6's though! 

I have always helped my dad with projects, but this was the first one I ever did without my dad! The directions were very easy and I had no trouble at all. The table turned out beautiful. I modified it a bit by making it a little longer and using a 1x2 on the ends to cover the rough edges instead of a bread board. I also made 2 benches as we are a family of 10. I have 2 high chairs attached to the end. This table will seat 12 adults comfortably! I am so excited to finally have a big sturdy table. Thank you sooo much for this site. I have a new hobby now! ;o)

Our guest bedroom has been utterly neglected and stark. When I found a pair of lamps at Goodwill recently, I knew it was time to make bedside tables.

These were created on the fly, without even a sketch or a trip to the lumber yard, though I had to select a plan title for this post.

I took a plywood scrap, cut it in half, framed it with 1x2 furring strips, added 2x2 legs, and then used more furring strips to stabilize the legs.

They were assembled quickly, and then I faced choices about how to finish them. I ended up using Minwax Provincial for the tops, then taping them off with trash bags and spray painting the rest.

They're plain, but versatile enough for whatever I end up doing to decorate the guest room in the future. I plan to stick baskets underneath them, when I find a good deal.

Next up will be a headboard for the bed.

i'm so grateful for all of ana's projects and plans!! we recently bought a new house and have decided to make much of the furniture so that every piece will be customized to fit the space... i'd rather spend hours in the garage making the perfect piece than spending days/weeks (and money!) to find something that "could work"...

i just finished my latest project from an ana white plan, easiest upholstered bench... and it WAS easy! the hardest part, for me at least, was the sewing.... but even that was straight lines, so not too difficult... and i'm so happy with the way it turned out...

a couple things i did differently from ana's plan were attaching the cover to the bench with nail heads... i like the idea of the slip cover for cleaning purposes... but it was getting "messy" every time we sat down and stood up... it just wasn't laying nicely... so i hemmed the bottom and attached the nail heads... i absolutely love how it turned out... this was my first time using those - and it was super easy... they came on a roll and every fifth "head" has a center hole for you to tap in a real nail head... the other four are just faux nail heads... the only issue i had with the nail heads was that the color was slightly off between the real ones and the fake ones... i read reviews about them and people mentioned a lot of the nails bending, but i didn't have that problem... so, overall, i was pleased with using the nail heads to attach the fabric to the bench...

the other change i made was to the foam... the foam at the fabric store was crazy expensive... and i had heard that getting the foam from home depot was much cheaper... but i couldn't find it at my home depot, so we bought a foam mattress cover for a twin bed... it was $24.99 - which is about 1/3 of the cost of 3" foam from the fabric store! the mattress foam was only 1.5" thick, but it was wide enough that we just cut two pieces and stacked them on top of each other...

other than that, we kept the dimensions of the bench the same as the original plans... it was already the perfect size for what we wanted... and we love it!

7.5' long cabinet, made with pine boards. Hardware purchased on Amazon.