Community Brag Posts

Took no time at all - 1 hour start to finish on a rainy day. Built it for the little kids but kids came out of the "woodwork" from all over the neighbourhood. Easy, fun and cheap! May add some old rubber bike tires beneath the seats to protect the wood that comes in contact with the ground. Didn't bother with a padded seat - an off-cut of plywood, with sanded edges works just fine and will be easy to replace if it starts to weather.

Built from the King Farmhouse bed plans

I love Ana's plan for lockers!  This project is so rewarding and was very straight forward to build.  I added a fourth locker and a shoe bench to accomodate my children.  I also added a toekick behind the face frame so things won't get lost underneath.   Instead of using 1 x 12's, I ripped plywood into 4 equal strips.  They came out to be slightly less than 12 inches each as you have to account for the saw blade.  Each locker has three hooks, a place for shoes, and a bin for winter gear.  I made the fabric bins and bench cushion following online tutorials.  I set the hooks according to the height of my children, so even my youngest can hang up her things.  This project took me about a week and a half to complete, including the sewing portion.  It is very sturdy and the 1x4's along the back allowed me to attach the unit to several wall studs.  I placed the 1x4's(with hooks) low enough that the heavy backpacks will also have the shelf for support.    The shoe bench measures 48" in length at the longest point.  It is the same depth as the locker unit and fits perfectly behind the locker face frame.  Thank you so much for your wonderful plan!

I used a pallet I found in a burn pile, cut it down, added a bottom piece from one of the other cross pieces, painted, stenciled, and covered it with a coat of poly. I then added potting soil and herbs, and screwed it into the studs of our porch. It's off the ground so my dogs can't get into it and my chickens won't sample the plants!

This is a customized version of a farmtable that my wife found here! 

I felt a little bold deviating from the plans when this was my first project.  But I saw another version of this desk with the breadboard ends, and I really appreciated the added craftsmanship this gave off.  Other than the top, I followed the plans to a T.  For the top, I made this from 2x6's with the 4 lengthwise pieces cut to 61" and the ends to 22" (I think I ended up trimming the ends down to match better, but 22 was a good starting point).  As for the finish, I layered stains starting with Minwax's Classic Grey followed by Minwax's Jacobean.  I made two of these desks to put in our home office.  If I think of it once the office is complete and decorated, I'll add another pic!

I needed a way to display some old pictures... I just love the look of old pictures and and wanted something different than an ordinary frame.This is one of the easiest and cheapest picture display project you can do.

A full tutorial can be found at www.AHouse-2-Home.com

Feel free to leave a comment on our site, we greatly appreciate them!

I built this Workshop Step Stool as part of the #GetBuilding2015 #BuildCave challenge. It was a very easy build. I had all the needed supplies in my scrap wood. But if you did need to buy the wood, you could do it for under $10.

I found the plan here. http://www.familyhandyman.com/workshop/ridiculously-simple-shop-stool-p… 

If you want to see the steps I took to build mine, as well as more pictures, please stop by my blog at http://jaimeofalltrades.blogspot.com/2015/04/diy-workshop-step-stool.ht…

Wanted to make a loft bed for my 4-year-old son's room that could accommodate a toddler bed beneath it for when my 1-year-old daughter eventually starts sleeping on her own. I was torn between the Chelsea and Cabin bed plans, but eventually settled on the Chelsea because I liked the look of the headboard better.

I looked through all the brag posts to get modification ideas. I ended up mostly stealing ideas from "chadwickstafin", and like him took the great idea from "groovymom2000" to use chalkboard paint (though I only used it to paint the side of the desk end, since I knew the bookshelf end would be mostly blocked by a ladder). I decided to skip the decorative feet and just extend my 2x2s to the floor for extra strength, a mod that most people appear to be doing with this plan. I saw some people using 2x3s in place of 2x2s for added strength, but I can confirm that 2x2s are plenty strong enough on their own (2x2s are stronger than people give them credit for, and there's 8 of them here to distribute the load).

Like chadwickstafin, I cut my headboard a little differently, and I used short lengths of scrap 2x2s cut at 45-degrees to brace the top and bottom corners of both end units. There is no wiggle to the bed at all, it's stabilized so well. I also added a middle support to the short rail, just for a little extra safety, and secured the inside ends of the railings to the headboard/footer with pocket screws. I skipped the filler pieces for the railing, and just did a little extra sanding to make sure all exposed corners were smooth and splinter-free. I made the opening to the bed a bit wider than the plans, 15" instead of 13". I used 2x3s for the ladder, which gave me the sturdiness I wanted without the full bulk of using 2x4s, which looked especially chunky next to a loft unit made with mostly 1x boards. I played with some different angles, but eventually went with a 15-degree ladder. There were some leftover plastic handles sitting in my garage (originally from an outdoor playset ladder before I replaced it with a climbing wall), so I added those near the top of the ladder for some extra safety. I put some color-changing strip lighting under the bed, so there would be plenty of light for the desk and bookshelves (my little guy loves to just plop down on the ground beneath his bed and read).

I spaced the 1x3 slats about 3.5" apart (used scrap 2x4 blocks as spacers). Because my wife or I will lay in bed and read to our son at night, I easily added a couple 2x2 support rails under the 1x3 slats for extra mattress support. I'm a big dude at 6'3 and 250 lbs, and the slats alone WERE strong enough to hold me when I did a test, but they bowed just enough in the center (unnoticeable to me up on the mattress, but I had my wife watching the slats for me below) that I felt I should add a bit more support. Now there's no bowing at all.

I also used Ana's Top Bunk Organizer plans to give my son a little extra storage up top (and a place to set a glass of water during the night), and painted it to match the bed's color scheme. Everything was sanded, painted, sanded again, repainted, and then given a couple coats of polycrylic (the painting process took longer than the cutting & assembly!).

Cost-wise I was extraordinarily lucky. We have a Habitat For Humanity ReStore near us, so I was able to get my paints and a 3x6 sheet of MDF for $15 total. I also had some rebate cards from Menards (regional hardware store, similar to Lowes or Home Depot), plus happened to go there on a week when pine wood was on sale, so I got all my lumber for less than $60.

I could not be happier with the end results, and my son absolutely loves his new bed.

This one was a lot of fun

We are in desperate need of toy storage in our playroom. We are planning to build several more of these bulk bins.