Community Brag Posts

I built these beds last week for the little girls and we all love them so much! I was looking for something girly and this fit exactly what I was wanting. I took some pictures of the build and posted them on my blog. Thanks for the amazing plans!

I built this table in about 2 weekends. The aprox cost including screws, stain, and glue was about $175. I stained it weathered gray from Rustoleum. My husband thinks it looks great. Now to order the end chairs!

The potting bench was my first ever project followed soon by the essential Adirondack chairs. All were made with reclaimed wood salvaged from a porch and from my husband’s scrap pile.

Kelly

After I built Ana's plan for the Low, Modern Cut Out Headboard, these two nightstands were the perfect compliment. I love the modern, clean look, and big drawer space. The inset design of the drawers make placing the faces on the drawer really tricky, so I would definitely place on the faces after you have installed the tracks and the rest of the drawers.

I started with Ana's plans and modified them for our specific needs.  We have a corner in our hallway very well suited for a shelf system like this, and my wife wanted to fill that area.  So, my finished project is 4 feet wide. Other than adjusting the plans for the width and then the lumber needs accordingly, all of the remaining dimensions and measurements in Ana's plan remained the same.  

I built everything using oak 1x4s and oak plywood, and pocket screws to build each shelf and the ladder portion.  

I read the comments here about attaching a piece of oak to the front of the shelves to hide the plywood layers, and wish I had read that before cutting all the pieces. I was able to make that modification without causing too much rework, I just had to cut the trim a little to match the new depth of each shelf.  

This piece is very heavy when fully assembled!  I decided to leave the ladder assembly separate from the shelves during the finishing process, and then carried everything to the living room.  I attached the bottom shelf first and worked my way up.

Each shelf is attached to it's respective support and to the ladder legs by wood screws, and each shelf is screwed to wall studs. Thanks for the plans Ana, this was a nice Christmas gift for my wife. :-)

I listed this project as Intermediate only because I modified the plans to fit our particular needs.  The measuring and cutting were relatively straight forward, attaching with the pocket screws took some time to get everything right.  Finishing took time to allow each coat to dry thoroughly.  Assembly also took me some time, just to make sure each shelf was level and ensuring I was drilling into studs and not sheetrock.

Added a few design elements to personalize for the birthday girl.

Deck sofa from a Ryobi/Ana video a few years ago. End table is also from Ana's plan using leftover Trex decking. Special thanks to Jen for her assistance.

If it was not for this site I would not think we could do this. Inspiration was from the IKEA LACK bookshelf and varioous craft desk tutorials on here. Bookshelf is 7 ft tall, 4 ft wide and shelves are 16 inches deep. Writing desk area is 3 ft long 2 ft wide. It could be done cheaper but it needed to hold all my daughters toys in bins so we paid more for the 16 inch deep boards. It only took a Saturday afternoon to build, but more time in decorating, clear coat of stain. It has a acrylic top writing surface.

Why should doorways be boring? I used 1x6 and 1x8 lumber to build a shelving unit around the doorway. Now I have somewhere to display pictures and creations from my kids too. Measure your doorway to see what size lumber works best for you. Prime and paint with Dove White and add white caulk to any imperfect cuts to smooth things over. BTW, cats love the shelves too!

This is my take from the Cassidy Bed plan. I still have to upholster the headboard...stay tuned

I made two of the chairs using cedar 2x4's and then stained them cedar color. The cushions were on clearance at Lowes for 6.97 each. Super excited about that as well. For the back I did the three board suggestion versus just the two for more back support and I also added an extra board for the bottom seating. Project was pretty easy and the instructions were easy to follow.

Carrie

I had just built the Tryde Side Table and it was so easy I gave a shot at this project. Took about 4 hours to build and is a really sturdy, good looking entertainment center. The only thing that I did not like that I would change is an overlap of the tabletop in the front. There is an overlap on both ends but not in the front. Other than that, I really like the outcome.

This was a super fun project to do and very easy too. I did this while I was nine months pregnant. The instructions were very clear and the total cost was great too!

Great workbench. Made slight modification, in extending the top 2x4s past the counter edge, and then connecting them with another 2x4 so I'd have a place to put clamps/tools. Also used 3/4 particle board, as it was significantly cheaper than the plywood my local hardware store had on hand.

Ana White … we love our chairs. We did make our chairs out of cedar and a side table from some cedar scraps.

These are simple, cheap, easy, and effective.

I modified the top so that I could just use the left over 2X6s I had and it would somewhat match my table. I felt it worked. There is probably something like $5 in wood in each chair about about 20 screws...that's it.

Word of warning, because you are using 2X2s these chairs will twist a little. Can't change physics but for $5 what do you want...

This is a fun little project that is quite easy but will make you think about how you can modify it and how/where you should use all your screws both to make it strong as well as to hide them.