Community Brag Posts

A new crib for a new baby. The foot and head board can be attached with the side rails to put together a full sized bed. In theory,  this should be the only bed they need for their little dude with just  a few additions (new footboard). 

Reclaimed wood headboard. Cost: $100. Time: 4 hours. 

After building one 6 Cube Bookshelf (http://ana-white.com/2010/07/well-i-did-promise-you-i-would-work-on.html) so my wife would have somewhere to store toys for the kids, I decided to modify the plan to use in our bedroom.

I chose to put doors on it, and learned quite a bit. Rather than 6 standard cubes, I went with a single divider on each shelf. The back and the doors are both made from some Bead Board trim packages that I found for about $12 at my local big-box.

I added a 16" wide board on the top to create the look I wanted.

I also want to note that when you're working alone, some right-angle clamps are lifesavers! Makes it a lot easier to keep square and hold things together while you drill and screw everything together.

I chose some hardware that came close to what we already had in our bedroom. The hinges took me 4 different trips to get right (first was wrong type (did not want self-closing), second was wrong depth, third was wrong color).

Overall I'm very happy with it and so is my wife. We replaced a piece of furniture that was twice as wide and it's amazing how nice it is to not have to walk around it when walking through our bedroom.

I am redesigning my family, which is really the children's playroom. I have decided to change it to a beach theme. I saw the project on this site and knew immediately it would be a perfect fit as a storage/coffee table. Within 5 minutes of me completing the box, my three year old started filling it up with toys.

I have to admit it is slightly tall for a coffee table, so I'm debating cutting off the legs. It would be easy enough to do without taking the entire project apart and it would make it the perfect height.

I did have to plan my build around my work schedule and the kids, so I did what Ana suggested and built a panel a day. I cut all the wood one day, then built a panel a day. The last day, I started putting the pieces together, put the bottom boards in and made the top.

I inherited the guts of a piano, and just had to make them into something funtional.  I am a musician, and these piano hammers were great inspiration for my next build.  I made a box out of 2x8s, braced them with 4x4's (which also added height) and attached some metal 2 1/2 in casters.  I set the hammers inside the box, and topped it off with plexiglass.  A functional work of art to be enjoyed for generations!  

I was so excited when I saw the plans for this and knew I had to make it. I love the way the wood looks with the numbers stained. It only took a couple of hours to get it exactly as I wanted. My kids love that they now have a place for all their crayons and school supplies.

I think the hardest part of making this table was making it square. I think a tutorial video would be very beneficial. Took me a while to make due to life priorities, but it is finally done! Kids have already taken it over! My favorite part is letting them draw on it and make it theirs. Will be fun in the future to look back. We also wrote the date on it. I do think clamping is a must. I didn't do that at first and ended up taking the top apart and redueing it with clamps and glue.

I didn't want cracks that food could get into, and those 2x4's are rounded. So I ran those boards through a table saw to make sure they are flush with the 1x6's.

I somewhat followed the general context of the plans for the bottom, but I added bracing and general durability changes to the plans. As the original builder did not take thought into the event of moving/ un- assembling, warping, expansion or durability. I used kiln douglas fir  (4x4, and 2x4) and kiln dried pine bread board tops. All bracing joints were predrilled and then screwed in with 4.5 or 2 inch screws, as a kreg jig joint should not have stress- I want this table to withstand someone leaning or in the instance sitting on the tabe to be safe- a 1/2-1.5 kreg screw would not work. I also changed the bread board to a 1x10- as most of the 2x10 at the stores were warped or chemically treated. Underneath we added bracing with an additional 2 2x4 beams, with cross beams in the middle to prevent sress. We opted not to have breadboards, as I did not want to mortise or tenon joint the ends. We followed close to the plans- but inforced stronger bracing to withstand weight applied to the table and easy dissasembly. :)

My cost was a little higher - but I did not want chemically treated pieces or warping. There was additional cost in 4.5 inch screws, and brackets but under 50 dollars. 

Aged rustic turquoise 

I loved this plan as soon as I saw it. The only modification I made was I used a 4x16 8oz drop cloth up on over the center instead of curtains or fabric and painted the wood with orange gloss spray paint. The kids love it. I think we may make come doors and ties to make it cozier but they love it!

My husband built the table and benches and I applied the finish. It pretty much took us most of two weekends, but was well worth it. We learned that we should have used kiln dried wood for the table top, since ours warped pretty significantly. We will most likely replace the planks on top of the table in the near future. Also, the plans for the length of the bench don't allow for the benches to be pushed in under the table. The supports get in the way (make sure your measure!). I used Minwax Ebony stain and wiped it off quickly after applying it, so that the wood would show through. I also used a satin finish to keep true to the vintage look, yet give the table some protection from the elements.

A few weeks back, my niece asked it I wouldn't mind building a Toy Box to auction off at a benefit she's holding this Saturday (December 5th - 2015). She and her husband are adopting 4, count 'em FOUR orphans from Latvia, so naturally I was more than happy to oblige. I didn't use any specific plans per se... I just used some pocket hole cabinetry I've seen on this site and others, as well as some pictures I found on the internet of different toy boxes and blanket chests for inspiration. The final project cost about $55 all in, including lumber and hardware. I used 1x3s and 1x2s for the frame, one 4x4 sheet of 1/4" plywood for the panels, and one 3/4" x 16" x 8 foot project board (which I got for $11 and change!) to use as the bottom and lid of the chest. For hardware, I used a couple of box hinges, a lid stay so that the lid both stays open on it's own and closes softly (gotta save those little fingers, y'know ;) ), and a cool wrought iron knob I found at Hobby Lobby for about $2 (gotta love the 40% off Black Friday Deals!). Oh... I also picked up a little quote plate from Hobby Lobby too, just too add that extra touch. ヅ Stain is Rustoleum American Walnut with 3 coats of satin poly.

UPDATE:  The auction was yesterday and the chest sold for $330!  ヅ

Made a little smaller than original plans and completely out of oak  

I've taken quite a bit of time building this project. My goal was to use all material we had here so, I had to cut down 2x4's and 1x6 tongue and groove. I am proud of how this turned out, now to build it's match.

I started with Michaela's Kitchen Island plan, but reduced the dimensions and material sizes. I used 2x2s for the legs and 1x3s for the rest of the project. Everything was kreg jigged together. This project would've taken less time but the drying time for the stains ate up work time! :)

I built these out of necessity to keep my tipsy Christmas decorations from blowing over. The last couple years I spent a lot of time picking these trees up off the ground. I like how they turned out and were relatively easy to build.

I was excited I got to use my Kreg Jig for the first time, which looked more difficult to use than it actually was. Although these are cedar planters I used all pine from big box orange. Some leftover from the farmhouse queen bed I built and the rest I purchased.

The finish didn't turn out as grey as I would have hoped using the steel wool and vinegar, but I still like the aged look. I added the "x" detail in the front afterward and instead of staining my wife thought it looked better natural. Either way I would have been happy. I will be able to use these year round in some capacity.