Community Brag Posts

This project was inspired and guided by the plans for the

Farmhouse Storage Bed with Hinged Footboard by birdsandsoap.

The most visible parts, head and foot board, are made of beetle-killed blue stain Lodgepole pine, locally sourced and milled.

The boxes are made of 3/4" maple plywood and rest on a frame of 1 by 2's. I am still working on the 6 drawers, which will have blue stain pine fronts as well.

The bed slats between the boxes are stapled to webbing and the first and last slat are held by dowels drilled into the supporting rails to prevent the slats from sliding around.

Knock-down design - by removing the few (non-loadbearing) screws that fasten the head/foot boards to the boxes, the bed can be disassembled into manageable/movable components.

We badly needed a new kitchen table since ours has been completely destroyed over the years. Not a bad table, but too "smooth and perfect" for our lifestyle. I wanted something darker a lot more rustic that would not HIGHLIGHT nicks and scratches so badly.

I fell in love with a table at World Market, but it was the wrong size. It's called the Napa Gathering Collection.  It comes in either a counter-height 3' x 3' table or a standard height 3' x 5' table.  Shorter table is too long for the kitchen and the counter-height one was too small.  *sigh*  Here's a photo of the set.  LOVE this!!!!  So upset it's so small.  World Market photo below makes it appear a lot more red than it is.

Anyway, it's made out of Acacia wood, so it was massively heavy and strong. I loved it so much that I bought the four gathering chairs and spent over a month trying to get Acacia wood without spending a fortune. No luck. So I decided the most similar table here on Ana's site was the Tryde coffee table.

I researched different hardwoods, but was so nervous to spend that much  money that I decided my first kitchen table would be a rough draft with super cheap wood.  LOL  If I love it then I didn't spend a lot.  If I don't love it, I will learn from it and can build it again someday with more expensive hardwood like maple. 

I used the 2x8 hemlock for the tabletop, hemlock 4x4 legs and finished hemlock 1x4's everywhere else.  I used cheap 2x2 studs for the support structure underneath.  This table was almost exclusively built using Kreg joins, with only a few exceptions where necessary.  No visible screw holes to fill ANYWHERE!  Yay!  LOVE my Kreg Jig!

Lots of sanding, Benite wood conditioner, red-ish dye, dark chestnut stain and three coats of poly later... and I moved it into my kitchen this morning!  So excited!!!  I love how it turned out! 

Used cedar for the planks in the headboard and footboard

Added some common trim pieces like the rope

Built the frame as described in the Queen plans - found that a standard metal ammo can on its side is the perfect height to set up the side panels at the corners.
Used 2x4 studs for the cross slats, but set them on their side to give some added height.

Used minwax Walnut stain - really looks nice on the cedar - just one coat for the cedar

Waxed top of the footboard

Stained a small footstool using Walnut.

Kingsize version is a monster - very solid, no movement or creaking

This was my favorite project I have made so far! And was a challenge to get the hardware just so. But I highly recommended giving it a try!

We added a nail head trim after

I liked the pb mail bin, but wanted to build the entire piece. Learning experience, measure twice. File folders will not fit, as the inside measurement is to small. Still turned out cool.

We haven't had a chance to hang the first bed but had to make it functional asap. So, we gave it temporary legs on the front and attached it to the wall in the back. We are thinking of replacing the desk and making a smaller toddler sized version there for one of our little guys as well.

modified plans a bit from on the website. Went with 4 x 4 legs, matching bench. hardware I found the turnbuckles at home depot 3/8 - 16, and picked up the left handed and right handed rods and nuts at grainger.

Built two simple deck benches from plans found on this site.

Here is a pretty simple shelf I built for my closet. Left it backless b/c I wear a 12 1/2 and needed my shoes to be able to hang out back a bit. The top 2 I am using for folded tshirts I don't hang, like undershirts and tank tops.

Material List:
1- 1x10x10 -$13.00 (2 side boards)
2- 1x10x6 - $8.00x2=16 (6 shelves)
24 1 1/4 pocket screws. Had these on hand, could sub for 1 1/2 wood screws if you do not have pocket scew jig set.

Tools:
Tape measure
Quick Square
Miter saw ( which I used) or a Circular saw
Drill

Cut list
*2-59.9+- side boards

*The 1x10x10 was exactly 10ft long, so I marked off 5 feet with a line. Then I just cut on the line with the miter saw. This left me with 2 equal boards. Lets say 59.9 give or take a MM or so. Doesnt matter as long as they are even. If you mess the cut up, stack them on top of each other and recut to equal.

*6-23.9+- Shelves

*Again the 1x10x6 was exactly 6ft, so I made 2 lines, one at 2ft, the next at 4ft. Split them when cutting, and had 3 equal boards. Size can be smaller if you like, this is how I did it.

Now the fun part, and probably second longest time consuming part, behind drilling pocket holes.

I took the 2 side boards and clamped them so they would be flush and even side by side. (both face down side to side so you have one clamped board of 1x20x59.5 so to speak) I used my quick square to mark off .75(thickness of shelf boards). Start at the bottom or top, draw line. then,start next at 11 inches, step and repeat.In the end should have 5 shelves exactly 11 inches apart.

I next predrilled my 6 shelf boards with 2 pocket screw holes on each side, about 3 1/2 inches from each edge. This was most time consuming, you could use 1 1/2in screws and go from side boards into shelf boards and save time, also if you don't have pocket hole jig.

Assembling, I started at bottom, attached side boards to both side of bottom shelf, and worked my way up.The lines you pre-drew act as marker for next shelf,and help a ton when trying to keep everything square. The last one,top part, should be snug to put in. I find its best to do this way as everything keeps square as long as you have straight lumber.

Cost overall-$30.00 since I had screws, total time was around 2 hours to complete, and this was me having to explain everything to the little one lol

My variation of the multiple plans / pictures I have seen.
I will be making another one this season, with an additional variation in mind to make the time it takes to make the whole thing less.

I made two different versions and reversed side the ladders were on. I learned from the mistakes I made on the first bed and the second one came together a little easier.

I left them natural and the girls will pick a paint color in the spring.

Although I can sew, my wife made both sets of mattresses along with a bunch of doll clothes.