Community Brag Posts

Done just in time for Christmas. Hoping for one happy 4 year old!

Just wanted to show my Weatherly Sofa (Sectional) that I built recently. I've been drooling over Ana's plans for months now, I waited patiently until I could get a good deal on a Kreg Jig since so many of Ana's plans use it. I purchased my cushions first, I really wanted Sunbrella fabric since they will be outside in my Lanai so they need to stand up to the Florida elements, I was so excited when I found the seat and back cushions for $40 a set discounted from $98, however I kept watching them after I purchased them and they eventually dropped down to $20 a set (called Lowes and they refunded me the difference), so total for all 8 seat and back cushions was only around $170...the problem with them however was that they were 25 x 25 and not the 24 x 24 that Ana recommends in the plans. I just modified the length of the sofa's by adding 3" and With by 1" which did increase my cost of wood since I was short certain pieces however I really wanted them to fit and not look squashed in there. The extra 3" made them fit perfectly. I also have 8 matching back cushions but they are a little too puffy to keep on there so I just use 2 on the ends and stored the rest. The small cushions I also purchased were on sale for $4 a set of 2. This was a relatively easy project. I was a little intimidated to use a compound miter saw to do my cuts so instead I just purchased a Stanley Clamping Miter box that was able to do the 30 degree cuts to make the x's. Total cost was $470 with all the cushions. I used Behr Weather Proofing Wood Stain & Sealer Semi-permanent in COFFEE which gave it a driftwood beachy look. It is so comfortable and sturdy. I love it and considering it was my first build from Ana's site I'm now hooked....Thank you Ana

So I didn't build it myself but I just wanted to brag anyway. David built these for my sunroom. We changed the dimensions a bit on the shorter bench and didn't put a back on them. He also cut a corner piece so there's not a hole there. I love them. I will paint them, gray with orange and blue accents.

I have tried all sorts of nest boxes. No one ever used them. I decided to make the one from Anna White's site. I used joinery to attach the various pieces. The best thing of all: I find girls sitting in the boxes and take eggs from them. It really is awesome. I got a photo with real eggs and you can also see the wooden eggs to entice them to try it out. Thank you so much! I will build another one for the other side of the the wall.

I made my daughter the doll crib with drawer from the pattern provided by Ana. I wanted to give my daughter a special baby for Christmas but couldn't imagine giving it to her without a crib. I cut and assembled the crib with the help of my neighbor, and then made the bumper pad, mattress, and quilt for the baby. I also made matching nightgowns for her and her baby. My sister also made an afghan to go along with the ensemble. There have been huge smiles at our house since she opened her gifts Christmas morning. Thank you for such an easy plan!

I made this taller and added and extra shelf. I also didn't add the angle cuts and for the front pieces. It was so easy and I built it within three hours with my 8 yr. old son.

I used the stick on drawer organizer tutorial to divide a giant dresser drawer

With the divider, the drawer can hold more and is so much neater and easier to use

i love there is ZERO planning or sourcing of dividers with this method  just have the basic materials on hand, open up a drawer and get it done  

I made this work bench for the Make Two Challenge but haven't found someone to give it away to yet. We did have fun building it though. Check out my blog for more details!

I needed a new double bed for one of our spare rooms (that had been used for storing suitcases, etc.) and looking at what was available, decided to make my own. 

I settled on standard timber sizes - 4x4, 6x4, 8x1, 4x2, 1x1, etc. and used pocket-hole joinery to tie it all together. 

As far as tools, a drop saw, battery drill and hand router/trimmer, along with measuring/marking/squaring tools.

The bed rails and stretchers are 6x2 Meranti (a local timber in SE Asia where I live), the posts are 4x4s, the support rail in the centre is a 4x2, the head and footboards are finished with 8x1s.

The slat support cleats and centre support rail were rough-sawn, the rest of the timber was planed - my thinking being that no-one would see either of those and I had a bunch of 4x2s lying around.

Very little measuring was done, other than for cutting the lengths of timber - I just cut a piece of timber to act as a spacer to ensure I had the rails and stretchers at an even height and set back from the edge of the 4x4s.

All measuring was done in metric, as that's what I am used to - so the 4x4s are really 100x100 - and after planing, 90x90, but my router bits are imperial, so I decided to use inch measurements in descriptions. The plans are in metric, but if you want them in inch, just change the 'model' to inch.

The 4x4s had a 1/4" groove 7/8" deep routed in to take a matching 'tongue' routed into the boards, which were glued in place. one 8x1 board in the foot and three in the headboard gave it a nice balance and reduced the need to rip any planks. The 4x4s were cut to accommodate those plank dimensions. The tops of the head/footboards were a ripped and shaped 8x1 board.

I routed a v-groove in the sides and foot to break up the expanse of timber, sanded it all down and used a dark stain - local meranti varies so much in colour, from golden blonde to ashy dark, that staining is pretty much compulsory.

As to method:

Cut rails, cut posts, cut stretchers - test fit.

Make 'spacer'

Drill pocket-holes in rails and stretchers

Route groove in posts, route v-groove in rails and foot stretcher.

Support end of rail, use spacer to get correct height against post and seat pocket-hole screws - same at the other end and for stretchers. This almost completed construction :)

Measure and cut slat - fit support cleats and centre support rail using slat as template/guide.

Use slat as template for cutting the rest of the slats - test layout/fit slats.

Glue boards in footboard and headboard.

Cap footboard and headboard with ripped board - panel pins and glued.

Finish sand, wipe down, varnish.

All in all, it is very sturdy - Meranti is heavy stuff. I could have used much lighter gauges of timber, but apart from the 6x2s, it was what I had lying around, so the dimensions almost dictated themselves.

I did do some further 'trim', by shaping the capping planks on my table saw - a quick and effective way of 'raising' a panel.

You can find the plans here: https://www.dropbox.com/sh/k99w5pik5pezmxa/pUU2TUwlKM

Needed to add a buffet console to the empty wall in our formal dining room.

My 12 year old son expressed some interest in learning how to build things. We looked for several "kit" projects but they all seemed too juvenile to him. In the meantime his "Grandma" (an old family friend) asked me to find her a tray that she could use to carry her cup of tea on so when it sloshed it wasn't running down her arm. I looked and looked but couldn't find one in the stores that had a handle that she could grip. I was very surprised and relieved to find the pefect project: this wonderful serving tray!
We printed the PDF, drove to the store and a few hours later- her tray was finished and my son was hooked on wood working.
Overall it was a very simple project- the thing that caused the some difficulty was figuring out the process for shaping the handle- that grid diagram was very confusing to us, but it may be because we are novices.
Aside from that- we could not be happier and we are looking forward to completing some other projects together.

2nd project. Made this for me! Love it. I bought 5 towels at Walmart for $2.86 each, extra firm pillows for $3.50 each and made the cushions. It is like sinking into Heaven. Glass of wine and a good book. Set for the day. I added another support half way through since people used it as a seat during parties and I was afraid it would sag in the middle.

The table was an after thought. I had leftover wood and and just gestimated measurements.

FYI, I'm a slow project person, so most could probably finish faster than I did.

Thank you so much for these plans! 2 weeks worth of nap time building and my daughter has an awesome new bed!