Community Brag Posts

I loved Ana's cubbies the first time I saw them. :) I used different measurements and set mine for one large cubby to hold class papers and the others each fit a mason jar that holds chalk/ eraser cloth/ misc. Measurements/Wood Used: back: 4" x 1" x 44" bottom: 3" x 1" x 44" front: 3" x 1" x 44" I miter cut the insert separators to go edge to edge. Setting was 31 degrees and sanding to finish top point to back I added the inserts last after distressing the front/back/bottom assembled. I stained the inserts with no distressing and slid them in and used finishing nails to hold them to place front and back as my last step.

I built this in small spurts over a week. The most time consuming part was waiting for paint to dry. I painted all of my wood before I assembled since it would be too hard to get in the crevices after putting together. I painted the table top at the very end after it was assembled. I used painters tape to make sure I didn't goof and the stars are stenciled on. I extended the table to 20 inches wide so it would look more like a flag and just adjusted my other cuts to make it work. I built one for my Step-Mom and had to build another for my Mom after she saw how cute it was.

I modified the plans to fit my space. I needed a shorter wide shelf. This project was easy and fun. Turned out great

I wanted to make this porch swing ever since seeing it in the plan catalog (Large Modern Porch Swing). Just a matter of setting aside a weekend to get it done and then to find A frame to support it. I made the A-frame from a combination of this post:
http://www.buildeazy.com/newserve/swing_seat_support_dec07_1.html
and this one:
http://www.hgtv.com/home-improvement/custom-a-frame-childrens-swing-set…

I made the back a bit higher on our swing... and not quite as wide.

Reading several other blogs on this- I chose to attach the chains to the top back of the swing to keep it from tipping backwards...

Now just get to enjoy it!!

Built two of these over the weekend. The first one took 7 hrs to build and the second one only took 3 hrs. Things I learned:

1) Do step 3 before you do step 2. It was a nightmare trying to fit the 1x12s into the rectangular opening. Once you get the 1x12s in there, you can sandwich the 2x2s neatly onto the sides without having to shave down the 1x12s trying to get them to fit.
2) Check for square as you go. This will be important when you get to step 4 and 5.
3) I don't know about other folks but the 2-1/2 PH screws were always screwing all the way through to the other side so I used 1-1/4 PH screws for most places.

And that's it folks! A gorgeous and easy side table. =)

First table my husband and I have ever made, and it turned out beautifully!

I used your plan as a base. I do not have space on counter so I chose to hang it on the wall. I placed dots of hot glue on the back to offset from wall and used D hangers.

This was my second big DIY project ( I should say DIO for Do it OURSelves) since my husband had to help me with a few things. Anyway, I chose to paint the whole thing the same color as my office/craft room; BM Revere Pewter. Then, I stenciled some flowers in different colors of gray and white on the top. I had a piece of thick glass cut for the top. When I need to do anything heavy duty (like the open shelf console I did next) I simply put a bath rug on the glass. Even so, it's pretty tough as I've dropped lots of stuff on it without a crack!
I made this from the plan in Ana's book. Before we tackled this, I pulled all the carpet out of my office and put in a plywood floor (ripped into 6" widths).
I just finished the console which was made with plans from Ana and Shanty. Looking to move onto the next big project; a bar cart with doors or a dresser. Yikes! This is fun!
P.S. Love my Ryobi One Plus tools!
Thanks Ana, for the inspiration!

First of all I want to Thanks Ana for such a great website and projects and all she do. Its amazing how a person can do all of that for free. If all Americans were the same we would be the greatest Nation by far (anyways we still great!).

     I wanted to make this bed full so I had to re-scale the dimensions and I wanted to share leasons learned.

First: The legth for a full size is the same.

Second the width for a full size will be 52 inches (I would make it 53in); if you are going to follow Anas design and use a 2x6 as a side rail then then the width of the header could be 53in.

I made a design change at the last minute (and paid for it at the end :-s). Instead of follow Ana's design I decided to use railing hardware in this link to be able to take the bed appart without any problem.

 Using these mortises I was able to change the side rails for 1x6 which in my opinion look way better. The problem is that now with those mortises the bed frame is going to be wider (56in), so instead of an extra 1in for play with the boxspring I have 3.5in :-(

My wife is nice enough and tried to gave me moral support and she insist that is not a big deal because the gap is toward the wall and my doughter can't care any less; she has her big girl's bed and thats all she wanted; but I know is there and I hate that gap!

Summary:

If you stick to Ana's design 53 inches for headboard is perfect; but if you want to use the mortise then 50.5 should work fine.

To paint the bed I did two coats of primer and two cotas of semi-gloss white paint; in my opinion for furniture I probably would go gloss next time, but this doesn't botter me.

I used prime pine wood so the price went to the $300, if you choose mid-grade pine (it has a lot of knot) you can probably drive the cost down by good 25%.

Time: took me one full day to build the bed and since I had to go to work every day and I was doing one coat of paint every afternoon after work (so "five" days total); maybe you can do the painting it in one day if don't have to go to work and the weather is right!

The foldable plant table with some modification to make it stationary instead! Freaking loved this challenge. Gave the 1st one away as a gift. Now selling one!

I wanted to do floating shelves in my bathroom but I have very limited space so I decided I was going to do floating shelves in a corner where I did have space. This is not going to be the only shelf, I will make another one to go above it. I was tired of having no storage space for things like toilet paper and towels so now we can use these floating shelves to do that for us :) Tomorrow I'm going to build the second one to go above this one. Making it for a corner is really no different than making it straight. The sleeve fit right over the frame I built and it looks beautiful I think :)

We started this project with Ana's hanging outdoor bed frame, added a vintage door as a back/headboard, and some panels from an old barn shed as arms.  Finished it off with some homemade pillows and outdoor mattress cover, and voila! Our family's new favourite spot to relax and read :)

This was the fourth plan we've used from the site, and every single time have been wowed by how easy it is to follow the plans, buy the material, and how well the projects come together.  Thank you so much for your generosity in sharing them, Ana.  We are so apprecitiative of your creativity, talent, and kindness.

Kindest Regards, 

The Culbert Family

What do you think ? I painted mine to match the tiles as I didn't want it to stand out too much. It's a useful item for sure, but I wanted the mirror and wallpaper from @thepureedit to be the focal points.

But what a great little storage unit from scrap wood. - shabby.ie on Instagram

We wanted some tall planters and found some tall teak planters that we love, but one problem $820 on the Casual Country website. The ones online were angled but I couldn't get the angle right so I made mine straight.
The tallest one is 42" x 23" then 29" x 21" and the small one is 20" x 18".

They will look much better when I get something planted in them this spring.

Built the frame with 2"x2" cedar boards and used 4"x1" cedar boards for the planks.

Made mine exactly like the layout except I used an old piece of glass from a different project that didn't work out so well. This 1 turned out really nice. Going to make a couple end tables next with a hidden compartments in them next...

40"x34" oak cookie. I tried some metal legs but couldn't get them wide enough to be stable at the requested 24" height, unless I had some custom made for $$$. I found these plans and changed the dimensions to fit the table and made the legs out of oak. Very pleased with the results.

I was looking for my next project for woodshop my junior year of high school. I happened to run into this website while looking for plans and found Ana's farmhouse queen bed and was inspired to make something similar. Now that I have accomplished this task, I want to share it with the community that inspired the build. Let me know what you think! Thanks.