Community Brag Posts

I had inquire on your Facebook about you making a new plan... i had wanted a side table to hide my propane tank. I used the planter plans as an inspiration for this table. It is regiment rough looking as I managed to build it using only scrap on hand. I did have one cedar board in my pile that was leftover from another project that I used for the top... pretty happy but know it would have been better with new wood that was the right size and not warped! The space at the top is on purpose to be able to teach in and turn the gas on and off.

My sister n law and her family were moving and sold a lot of their furniture, so I built these as a Christmas gift. They came out great and I think they really appreciated it!

We made this a double bed and lowered the height by 3 1/4 inches because we have low ceilings. We added an extra support under the mattress since it's a double. Plan to add the desk and low shelves later. Followed the plans very closely, worked out great. One thing I would suggest is to do the slats after the guardrail. Otherwise you can't stand under the bed and it's hard to get a good angle when screwing it on. Many happy hours of reading Harry Potter up there in the first week :).

Outdoor couch excellent plans, easy to make and result is amazing.

This was our first woodworking project. I was not that hard to put together.

I made a couple of changes to the design. I used 4x4 for the legs. I also change up the board that were used ontop. I have a step by step on my blog.

The almost the same as the table. Check out the changes and the cut list here: http://www.domesticated-engineer.com/1/post/2012/05/bench-for-farmhouse…

This is my first fully finished build. My very good friend was about to have her first child and I wanted to do something special for her so I embarked on this project. I had HD cut my wood to size. After I came home and started building I found that my wood was not exactly cut to size. One side was one quarter inch too short. I did some improvising and some trimming with my jig saw (only saw I had) and was able to eventually create a rectangle.

This is also my first mitered trim project. The edges are NOT perfect but what I could I filled in with wood filler. That helped hide where the edges did not quite meet.

I then sanded and sanded and sanded. Don't want little fingers to come into contact with bad splinters. I finished with a bright white paint.

I wanted the toy box to also be a seat so I got some fabric and did just that. I was going to add hinges to it but then thought again and decided not to. Wanted to prevent any accidents.

I built it over many months spending maybe 20 hours or so. Many many mistakes and many hours thinking about how to fix them.

I took a crib plan I saw on here from DIYstinctly Made, but I wanted to have a crescent moon, so I altered the plans to a solid back with a crescent moon in the center!

Such a fun build! Can't wait to start my new project 🤗

Jenuri

This is perfect for all of the trophies and pictures around the house! Now I need three more.

This console table was actually pretty easy to make. The top was constructed with 1 x 6 pine boards, and assembled using a Kreg jig and pocket hole screws.

For the base, I used 29" long, 2 x 3 legs attached together with 1 x 4 aprons. To make the platform, I cut 2 pieces of 2 x 6 the width of table top, and 2 pieces of 2 x 4 , two inches shorter. I stacked the 2 x 4 on top of the 2 x 6 and attached them with glue and screws. I then ran 3/4" cove moulding in the corner between the two pieces.

Using my Kreg jig, I drilled 2 pocket holes on the inside of each table leg, and attached the platforms. I then cut and mitered 4 pieces of 2 x 2 for each end, notching them in the middle to create X's. I attached the X's with glue and finish nails.

The last step before finishing was to distress the wood. In addition to hammer, chains and nails, I skipped a hand planer along the edges to create a "hand hewn" look.

For this project we followed the plans pretty well. We added trim to the side rails to be more like the original bed which the plans were modeled after. We also extended the two by fours on the headboard and footboard to give s little more design to the headboard. Plans were easy to follow. We love our new bed with the natural wood combined with a light white wash on the panels.

Built this garden bench all from recycled fencing materials. I didn't want the wood to go to waste, so I've been reusing all of it on garden and outdoor yard projects.

So I had some leftover fencing material sitting around and I decided to try to make something out of it. I really don't have anything to compare this to on the site but I think it works for the primitive minds.

Made using the plane old shelf plan.

Modified to be able to be taken apart and easily reassembled into 4 frame pieces (each side plus the middle support beam) for transport at will, and made to fit a Queen bed instead of a double.

Built by Boatman