Community Brag Posts

I wanted 2 large lego tables but also didn't want to waste space...so I came up with this! The top flips over and it becomes a desk.

I used your plans to build this one, but I put a back on it and legs instead of hanging it on a wall. This was made for a senior center, so they can use it inside or outside
Donna Brown
Miniota, Manitoba
Canada

I've wanted to build benches for my dinningroom table for years. When I first saw the plans for the spa bench 2 years ago I bookmarked it, saying thats the one. Now all this time later Ive finaly gotten to it! I modified my benches by making them longer, they are 48 inches, adding the dividers/supports to the inside to make 3 cubbie compartments, (I will eventualy put baskets under there to store stuff) and raising the bottom edging up a half an inch to create a lip to keep the baskets on. I made 2 benches, sanded and restained my table at the same time. the benches took about 3 hours and $50 each to build. Simular benches cost aobut $150 for the cheep particalboard ones, thank you so much Anna White for making this possible!

Adirondack Chair

I needed to replace my particle board entertainment center. So here is my final project

1st time making one turn out pretty good.

The storage on the dresser is great! I added a changing table top with routed dividers for changing pad and other accessories. I attached the top from above into the dresser frame with recessed screws so it can later be removed and a plain top added (I added a cross bar in both directions to the dresser frame under the top to support the additional weight). I used rough cut poplar from a local lumber yard except for the drawer boxes which are plywood. The legs on my version are made from 2 1x2½" boards cut on a 45° bevel on the table saw. I used full extension side mount metal slides. It was somewhat difficult to attach the drawer slides with a very pregnant belly - my husband helped out with that, not to mention lugging around lumber and painting. It helps to have an extra set of hands on assembly with a big piece like this. Thanks for great plans.

I followed the plans provided by Ana and boy am I delighted.  I changed up the color scheme based off a whim.      All the stained pieces or cordavan brown semi transparent from Home Depot and the wood is pine.     All the white is Douglas fir, (4x4, 2x4, 2x10) and I used a chalked white also from Home Depot. It was fairly easy, I just tweaked the dimension due to our bed height.   Great weekend project.  Beginner project to certain extent, turned into a intermediate based on tools used and certain finishes. 

Measurements were for a queen bed frame and tempurpedic adjustable bed frame (had to adjust post height to be taller,  adjust 2" shorter for standard Hollywood frame)

Follows your plans and it worked out well.

I made this from the Simple Play Kitchen Plan. I recently purchased Ana's book, and it inspired me to finally build something on my own. I am proud to say I got it done within a few weekends, with minimal issues.

Needed a wardrobe for a 24-inch wide space. Not sure you could buy such a thing -- certainly not in the small town where we live. Glancing at Ana's "Toy or TV Armoire" plans gave me an idea how to proceed.

Didn't plan for drawers, initially, but turned out I hadn't pre-stained enough trim for full-height doors, so decided to add drawers. Glanced at the insert plans, and it didn't look too bad. Decided to build the drawers right in with 22-inch 75lbs sliders, since again, not enough trim for full doors. Also, I think it might be tedious to first open a door or in my case doors just to get to the drawes. Miraculously, cabinet turned out to be square enough (+/- 1/16th inch) for the sliders. Here's to $99 table saws and pocket hole screws!

Thank you, Ana, for this and the other plans I built (craft table). Also, I admire your webmasters Drupal-craft!

This is my first carpentry project. Bought my house recently and it had the white wire organizers on the wall but I wanted to do something different. Only had 6' width to work with so had to shorten it a bit and lose the middle shelves. Lowes didn't have enough 1x4's for the shelves so I used 1x8's and just left a gap in the front which in my opinion looks good.

This is a century old red oak fireplace mantel I bought off of Craigslist. It came out of a home in Louisville, KY. It was in bad shape as you can see in the photos. I stripped it and replaced the veneer that needed it. I had to modify it a bit to install it to my mother-in-laws brick fireplace. The mirror is mercury glass and beveled. I did add some red oak rope trim which I beveled to give a more formal look. I countersunk some holes along the sides that I covered with some red oak trim. This allowed me to attach studs to the brick and then attach the mantel to the studs. The very top shelf was rotted so I found some beautiful spalted red oak and rebuilt this. The former onlay on the front was beyond repair and I found the current salvaged onlay on Ebay for around $10. I am really happy with how it turned out.

I am a complete novice, learning as I go. But the plans were so straight forward and well written that I got brave and added some cubbies! So happy with the nook and it helps when trying to get three little ones out the door for the school bus in the mornings. All of the things they need are in one convenient place. 

I love taking good stuff that people throw out and up cycle them. Someone on my street had thrown out two sofa sets and the cushions were is perfect condition. They had slip covers on them too. I washed the covers and built the sofa to fit the cushions. I built two single chairs, a love seat and a matching table. Super happy with the way it turned out.