Community Brag Posts

My first ever building project! I learned a few important lessons: it's really hard to make a straight cut with a jig saw, and you have to use large hinges (the tiny hinges I put on there first ripped right out). It was a great learning experience, the fences really were easy to build, and my two-year-old LOVES them! Now I'm ready for my next project. :)

I needed a step stool for my son to be able to reach the bathroom sink to brush teeth and wash hands. This plan was exactly what I was looking for. As I do with all first time projects, I built this out of inexpensive pine. It is very sturdy, and holds me without a problem. I routed the edges of the treads, and used 1x3 material for the braces as opposed to the 1x2 called for in the plan. The plan was easy to follow and the cutting list worked perfectly. The most challenging part was creating the curves with the jig saw, but truly wasn't bad at all.

I finished these night stands this past spring. I followed the Kentwood night stand plan from Ana-White, but made a few design changes. I decided to arc the doors to give the tables a little more character. The material I chose was 3/4" pine. The table bases are finished off with 3 coats of Sherwin Williams paint, and the tops are walnut stained with 3 coats of poly. The contrast between the base and the top came out great, the stands look beautiful in our bedroom and offer lots of storage.  

I was inspired by Ana's 4 Hole Cubby Bookshelf and a bookshelf I saw on line one night. So I incorporated the two somewhat. I took stair parts for the corner legs and connected them to form a frame with 1x3 on the bottom and 1x2 around the top. Then installed the inside side walls such that the ends are inset. I added a top with an inch or so of overhang on the sides and front. I also made the two shelves adjustable with my new Kreg Shelf Pin jig. It was so easy and accurate. Dimensions are about the same as the 4 Hole Cubby but I admit I winged it at times. Came out very nice and now the wife wants to add another shelf and I think there is plenty of room.

I used Ana's Gaby Kitchen Island plans and shortened the island to fit our small kitchen. I did not have reclaimed wood, so I used a vinegar and steel wool solution to transform the fir and pine into a completely unexpected look. For the top, I trimmed the edges of the 2 x 6s with my table saw to get a smoother top surface, then routered the edges with a 1/2 inch round over bit (thanks Steve Ramsey). I used white pine down the middle to make up for the edges I removed which looks like a cool custom stripe. (I also used the white pine for the side supports so hopefully there's some cohesion.)

Thank you Ana for the inspiration and great project! Can't wait for the next one :)

This was my first ever time building anything, even though I've wanted to for a really long time! It was great! I love this website. Wish I had a nailgun at the time I did this project, but I did get one after I realized how much I love carpentry. Thanks Ana!

Was very easy and fun to build , built from very easy and cheap console table plan

This is my first project using Ana's site. The step by step plans made is really easy. I enjoyed it so much. Can't wait for my next make!

We're expecting a baby in November and we picked this as our first Nursery Decor project!

We were originally inspired by the Letter Z project we found on here on Ana's site. So we went ahead and made our own design on google sketch-up. It was a good first project for us to learn how to use Google sketch-up (although we still aren't very good at it).

We wrote about building the project on our blog here: http://thehuth.blogspot.com/2012/10/brought-to-you-by-letter-h.html

This was a fun project and we love the way it turned out!

I've been meaning to build a coffee table for a few months now. About a month ago we received a hutch from some family friends. The back of it was made of 3/4" tongue and groove boards. So, I used those boards to make the top of the table and a couple of 2x4's to make the base. It's got a cool rustic feel that goes really well with the beach chic design that we have in our living room. For the design i really liked the look of the x picnic table, so I modified it for a coffee table.

I modified this plan slightly in how I attached the legs to the table top. I put screw inserts into the bottom of the table so I could screw the legs in and not worry about the wood stripping. We move often and I can't move the whole table assembled. Also, I haven't secured the cross beam, so this table will completely flatten and be easy to pack.

This table was made using the original farmhouse table plans with pocket holes.I tapered the two inside sides of the 4x4s (25%) and subtracted the bottom support structure. All pieces were glued and screwed using the kreg system. Even without the lower support this table is rock solid. I choose to make this table look a little more traditional then the farmhouse table to match our design plans.

All parts of the table were sanded down smooth to 180 grit and treated with minwax prestain wood conditioner. The table was then stained with cabot premium wood stain and sealer in one(espresso -satin). Warning large surfaces are hard to stain evenly with out brush marks using this product. I used 3 coats in all with a light sanding using 600 grit after the first coat since it is a water based stain. It covered just a little more of the natural wood grain then I would have liked but I did prefer it to the polyshades product I used on the custom bench behind it.

When using pine it maybe best to just go for the distressed look. I am worried that my smooth table top will get destroyed by my son but he knows he isn't allowed to play cars on the table now so I am crossing my fingers. So far the table top is holding up very nicely to any abuse but it is still early on in its life.

I think in the future I will bite the bullet and use hard woods. As long as it takes to build furniture its nice if it lasts a little longer.

We made the table with modifications to extend it from 72 inches to 96 inches. We created breadboard table ends. 

Over the last several weeks I’ve built a few different variations on the Easy Jewelry Box plan:

A narrow tower style one for my Hubby to use in the office at home, using 1x6 and 1x3 for the drawer sides, and 1x10 for the dresser box sides (no overhangs on this one) measures 10 ¾”wide x 24 ¾” tall. The drawers are not lined. The bottoms on these drawers don’t have felt – I used wax on the bottoms of the drawers, and also on the shelves, and they slide just fine.

The wide tower – this one is wide enough to hold paper and office supplies, and was made to the same height as the original narrow tower. The drawer sides are 1x3 and 1x6, with 1x12 as the dresser box sides (measures 16 ¼” wide x 24 ¾” tall). These are unlined, and also got wax on the bottom of the drawers and on the shelves.

I’m going to make a top to go across both of them so it’s the same height as the keyboard/mouse, and paint it to match the desk surface (BTW – the desks are a variation on the Rustic Table).

Distressed storage – the drawers for these are some strips of ½” plywood that were left over from another project. The dresser boxes are from 1x8. Also for these I left off the overhangs, and used the Minwax stain pen on the edges for a painted distressed finish. I liked the first one, and ended up building another to match. Each one measures 8 ¾” W x 10 ¼” T x 7 ¼”D.

Also, one of the easy jewelry boxes made exactly to the plan, with a weathered gray finish and the optional drawer divider. I’ve built more of those in different finishes, but they will be gifts, so I won’t brag those just now.

I used up a lot of my scrap wood, and the paint was what I already had on hand. Most of the knobs are from Target (the multi-packs were cheaper than buying the single knobs).

I fell in love with this table and decided to tackle it as my first ever furniture build. We spent more money that we'd planned investing in some new tools (i.e. Kreg Jig Mini and Clamps). We also had a lot of anxiety about initially getting started and trying the Kreg Jig for the first time, but I watched Ana's Kreg Jig Tutorial on Youtube, and it was actually very easy.

I'm going to say that it took us 10-20 hours to complete, because of the way we finished the table. We only worked on it 1-2 hours each week though, so it took us a couple months. :-)

This table is now on our patio where we can use it for toy storage or as a serving buffet for BBQ's. I'd call it a success! Thanks Ana for the inspiration!

For this project, I wanted my faux fireplace to look very similar to a real fireplace (of course!). So in orde to do that, I added a little more depth by using 1x6 boards instead of 1x3s. For the front of the piece, I added the faux brick wall paneling from Home Depot and used the spackling method to give it that weathered appearance!!