Community Brag Posts

I love this farmhouse style. It's 7'x3' and 30" high. I got the plans from Ana white. I just made a few changes. 

I used a combination of Ana White's book, The Handbuilt Home, and her website plans to build TWO twin sized headboards. I did not build the rails and/or footboard, because the room is too small. I simply attached the metal bed frame to the posts of the headboard. My boys love their new beds!

This was a fun project for my three nephews for Christmas (ages 3, 2 and 2). I thought they'd each like their own little personalized desk for coloring, blocks, snacks, etc.

This was a relatively simple build with the only tricky part being the leg holes (and getting the legs to open at the exact angle I wanted). I had to fudge a couple of them with some patches that you can see in one of the photos.

I would suggest using lock nuts on the bolts. The original nuts I used were turning as the legs opened and closed. I thought that eventually the nuts might work themselves off the bolt.

The frame was built completely out of 1x6 scrap wood I had lying around my garage that had been used for shelves. I cut the 1x6s down to 1x2 and 1x3 with my table saw. I did buy a small sheet of plywood underlayment for the top.

I added black accent brackets to this project to give it a more unique feel. Love it!

Followed the plans on the site but made it 3" wider to better fit our electronics.

built for my mother, for all the grandkids

Made a couple of mods because I didn't want shelves on the two ends and changed to "z" doors. I had a welder make the hardware. 

There are three plans combined here in this picture. All three completed in the past year. The toy boxes are from the one plan, the cubby shelves from another and finally the dress up stand is the third. It is never this tidy in our playroom! Ah ah, what you cannot see is the other half :D But the girls do enjoy it quite a bit and it does keep most toys off the floor and easily accessible. Thanks Ana for a great variety of plans!

I saw an outdoor Pottery Barn Table that Shanty 2 Chic did, and used the same plans they collaborated with Ana White on.

Table created for the chartering organization for Troop 4900 in Woodstock, GA (Woodstock Community Church).

Some deviations from the plans...we notched two of the cross member that support the seats and glued/screwed them together for greater strength in the center. That left 4 supports to be installed with pocket screws (weak). We added two small 2x6 supports where all these members join in the center and screwed the supports to the cross members, reinforcing the center and taking load off the pocket screws (see photo). Also, as you can see, we built the framing for the seats and table top, then added legs and placed the table top last to assure a level table top.

Finally, a recommendation - use 1x6 boards for the table top and seating areas for a lighter and more manageable table.

Modifed the Rustic X console to fit the width of den area's windows. Wife wanted storage, I needed a project.

Thanks for the great plans. I modified them slightly by building a 60x40 farmhouse style top and a double pedastel. The other change is that I made the side 4x4s into 2x4s. 

I accidentally found these plans on Anna's website when I was looking for deals on mattress sets.

After mulling it over a while, I decided to give it a try.  It just so happend that it was our anniversary coming up, and I thought hey, better than dinner and a movie.

I reviewed the plans, and upgraded the wood to entirely knotty pine. Even the posts.  Since I couldn't buy what the plans called for in knotty pine, I bought cheap pine shelving and milled the pine, then laminated for the posts, 2x4s, 2x6s and drawers.  Easier to work with than plywood.

About 35 hours later, I finished the pieces and parts with Polyshades Royal Walnut, and voila!!! 

My wife absolutely loves the bed, and now she even has a place to store more shoes!

I was looking for a "super easy console table" and once I was ready to build it, I mustered the confidence to try a more complex table top design. Using pocket hole joinery, 2"x2" legs and supports, scrap 1"x2" "blocks" for the herringbone pattern, scrap 1/2" 8"x4' plywood, 3/4"x1/2" pieces to frame the top, and much wood glue, I built this 8.5" narrow console table for under $30. The plan shared on this site was one of the inspiration pieces that helped me believe I could do this too!

Finally got a miter saw and a pocket hole jig. So decided to try this for my first project with new tools. Turned out great and I learned lots of things I'd do differently next time to save headaches.

Needed a night stand for my sons bedroom. this was perfect....

this project called for sewing the cushion covers, but i was to lazy to take out the sewing machine, so instead I stapled the fabric and it turned out pretty good if I do say so!! thanks for the plans!!