Community Brag Posts

We made this for my husband's Granny who has a bright green thumb, campared to my slightly black one. It turned out great.

This is also the project I learned how to use a Kreg Jig. Amazing. My husband is hooked.

Built this over a week because the table top needed to dry and harden. I decided to paint the whole thing to make it look decent. I Kreg jigged four 2x6's together and added wood hardener to the table top. It was pretty weak because the wood was still wet so I had to dry it out for a few days. I also filled in the gaps with wood filler and then used a belt sander to smooth everything out. Everything else were just 2x4's. I knew it would be heavy so I added wheels to move it around and as a final touch I am adding 90 degree iron accent brackets to the table corners but I haven't got those delivered yet. I also added rubber screw-in feet so that the bottom doesn't chip when you move it around. Got those from Home Depot for $3

I wanted to try attempt the beam table and my son's wedding rehearsal dinner was the perfect reason. My wife liked the table so much, she asked me to make three more. Because they will be used in our new wedding venue business, I wanted them to to withstand the weather. The materials were quite a bit more expensive as I used 10 ft x 3 ft  x 2 3/8" thick redwood butcher block planks for the tops and cedar 4 x 4's for the bases. Stained and sealed with Cabot sealant. What do you think?

This is a modified plan for Ana White's Farm House Table.

I shortened the table to about 72 inches with breadboards on the ends and added removable breadboard extensions for a total of about 100 inches of table for a 12x11 room. I also built the Farm House bench but shortened it to 48 inches.

The wood is white pine and Douglas Fir 4x4 legs. The total cost was $198 for the wood/screws and about $30 for the stain and sand paper. I bought an additional set of countersink bits for holes.

I used the following tools:

• Hand Saw
• Table Saw
• Compound Miter Saw
• Hand Drill with various bits and countersinks
• Square, pencil and straight edges
• Tape measure
• Clamps
• Wood Chisel Set
• Sharpening Stone
• Level

• It took about 35 hours of work.

  The stain is English Chestnut and we pretreated the wood to accept the stain by using wood conditioner. This made a dramatic difference in leveling out the stain between the white pine and Douglas Fir. I used 3 coats of clear polyurethane and 2 coats of satin on the top with gentle sanding in between coats.

This was one of our early builds.  I"ve learned a new way to do doors since then so hope to replace these before we move.  I love all the storage on this unit!  The finish on the tops is a metallic glaze I made.

Our version of the outdoor sectional.  We couldn't find 24" wide pillows so we modified the design to accommodate 22"x24" ones.  We also added a 1x8 held on with pocket screws to provide some additional support on the back and help keep the pillows from falling through.

I needed a small nightstand and was able to build this with wood left over from the Farmhouse table project, it's not perfect but I love it.

Super Easy.. I like it better without the doors. Recommend getting a KREG Jig. I have the Jr and it was perfect for this project.

I added metal corners made by bending 1 1/4 x 1/8 inch flat bar and attached with 1/4 x 1 inch lag bolts 

Decided to build these as I could find anything tall enough to be bedside tables. Easy to follow plans that came together quickly. 

This feeder worked out great for Sammy, who is about 95#. He seems a lot more comfortable now (and has started using his water dish instead of the toilet! ;) I wanted a more rustic look but wanted the easy clean up of tile on top.

My wife and I need a big dresser for the new addition to our home.  So instead of a media console we turned this into a dresser.

I built the Simple Bed for one of our kids and now we wanted a bunk bed.  I saw many plans for bunk beds based on the Simple Bed plans, but I didn't want the ladder on the side.  I made some changes and designed the bed in 3D using Autodesk Inventor.  It didn't turn out much different than I planned.  It's super heavy, but very stable.  My wife did a great job on the stain.