Community Brag Posts

DIY Wood Outdoor Chairs

This project was quick and simple. Just keep in mind and pay attention to the plans where they state "bevel" or "miter". There is a difference!

This project was free to me as we have a huge amount of 2x4 studs left over in our garage from a previous project so I should be able to do the table and another bench for free as well.

It went together within a few hours as the cuts are easy.

Working on the camp loft bed now with some mods to add a stationary bed beneath and more height for my girls room.

Overall great build.

I stained it with one coat of Kona. I did let the stain sit and barely wiped it off that is why it ended up being very dark which is the look I was going for. I then finished it off with 4 coats of polycrylic clear in high gloss which dries very fast and does not yellow.

We used the Weatherly plans for this project amending in a couple of places. The two seat version was attached to the three with using just one set of legs and then we added a 2 x 6" upright at the join and put another 2 x 6" on top for a drinks tray! Rather than 8 individual 24" cushions we went with 48 x 24" seats and did the same for the backs.

The cost for materials was only about $70 and the outdoor fabric was twice that amount. As it is under a covered deck we just used 4" foam for the seats and 2" foam for the backrests, costing about $100. All Canadian Dollars.

I had a big empty wall in my den/man cave, so I decided to build a dartboard cabinet instead of just hanging a dartboard on the wall. No plans for this, I just made it up as I went. Measured twice, sketched it out and cut as I went.

I use pine 1x4's for the frame and back. 1x3's for the accessory box, 1x2's for the door frame, and poplar strips for the doors and door braces. The darts are held by 6" long 2x2's with holes drilled.

Wood screws, finish nails, and small brads were used to hold everything together.

The chalkboards are simple MDF's cut and sprayed with chalkboard paint. Overlay hinges are used for the doors, and the dartbord is held on with screws from the back so it can be replaced when needed.

The Alabama A is hand-painted.

I modified your plan for a friend who wanted a slanted part. She is thrilled and so am I. Thank you so much for the plans and step by step instructions.

This is my 3rd completed project. This has storage, individual hinges was used.

I am still on the sofa after 9 months could not decide if I wanted to make storage.

I built the cherry stained easy kitchen island for my own kitchen... After friends and family looked at it, my daughter' smother (of course my ex) asked if I could buiild her one... we love both of our "islands" even though we both have them along walls in our homes... I added a second shelf for extra storage but it's great for what I call a grocery drop off point... Very sturdy and they both compliment our kitchens... I don't have a picture of it in her home (both of these were in my home on different floors of the house) but she says it matches well with her oak cabinets... Hope you like them :)

My dad helped me build this. I wanted to make one out of crates similar to another post but we decided on plywood and my dad wanted to play with the portable saw he bought me. We customized it for my space and didn't use any plans. I think it turned out nicely though I may need another for all my other shoes!

I bought my first home in July, and have been looking for furniture to fill it with. Then I found this site, and decided I would build what I want. I plan on making the iTable as well, but for my first project, I thought about starting a little smaller. I also needed side tables for my couches more. So was born the iSideTable ;)

23 3/4" high
10 1/2" wide
22 1/2" deep

Materials used:
1 4x4x8
1 1x4x8

All told materials alone for this project is a miserly $23!!

I have just finished my first coat of Varathane Kona (it's what we have in Canada). I want it nice and dark so I am leaving it on to dry, then applying a second coat.

This is my first attempt to build anything since the age of 17 (school!). I have recently bought a house and tried my arm at installing skirting (base boards in the US I think?) and it piqued my interest. The family needed a table, so I built one..

Its not perfect, but I'm looking forward to many family meals with our young family :)

Total cost was around $170. I used western red cedar for 4x4 posts and 2x4's, all the rest is carpenter pine. For the slats I decided to go with .375" dowel pins and drilled holes to hold slats in place. I sunk 3" screws through frame to connect head and footboard, if I decide to move it one day, I will just remove screws and do the same again. The finish is Milk Paint, i absolutely love it, mostly because it is 100% non toxic for my kiddies :-). The bed is for my two year old who is delighted with it! Thanks Ana for once again saving the day! We have such great and solid furniture because of you!

Bucket Garden made out of 2x4s and painted with outdoor paint for many seasons of use.

We LOVE this Rustic X Console table! We used a Kona stain and we took the iron hardware and rusted it up with heat, vinegar, salt and hydrogen peroxide.

This was for my 5 year old son and it was much easier than we thought it would be! We didn't have a nailer when we did this and wish we had one! Get a nailer for this project!

Our fireplace only had a  granite surround and was lacking personality. The wall that our fireplace is built into is kind of a strange size and all of the mantle kits won't fit our fireplace. It wasn't until I ran across Ana's plans that I knew this was exactly what I wanted around our fireplace!  We adapted the plans a little bit, and created a ladder up the sides of the fireplace  to attach the front plate onto. I couldn't be more thrilled with how it turned out