Community Brag Posts

I made the first of these directly from the plans on this site. I adjusted the second version a bit to ease the angle of the seat (a bit tough to get out of the original one for us old folks). I did this by changing the first cut on the stretcher bar from the suggested 20 degrees to 15 degrees. Hope the picture show the different angle of the seat. Three coats of Sealer/Stain and four costs of Spar varnish should allow them to make it through a Minnesota winter. - Rusty Rover

Used cedar wood so I applied a few costs of oil based polyurethane to compensate for the softness of the wood.

This project took a lot longer than anticipated. I had the entire bed built when it somehow fell over on its own and broke into pieces. It was at that moment that I decided when I rebuilt the bed that I would not use MDF. I used 3/4 ply for the back and I ripped a 1x8 for the top of the head board and foot board. I also used 3/4" half round to cover my semi noticeable saw marks from ripping the board. I didn't have a metal gram for the bed so I made rails out of 2x8"s and ripped a 2x4 in half to make the ledge for the slats. For this bed I placed 3/4 sheeting down instead of slats and set the mattress on that. I also had to fill in the holes from the crown with triangular fillers for the foot board since it would be seen.

I had so much trouble deciding what to do with this HUGE closet in my breezeway.  Previously it had just one bar across the top and ugly sliding doors.  I loved Ana's design, but made several changes.  Since my closet was super deep (32") I extended the depth of her design to about 25".  I also staggered the rods for longer coats, and one that my 8 year old can actually reach to hang her stuff up!  I changed the shelf design up a little bit too!  Her instructions are super easy to change to your specifications.  I did end up spending about $350 on this project, but keep in mind I was using 3 - 1x8's for each shelf instead of 1x4s.  

My son wanted the baker's rack in my kitchen to use as a coffee bar, so he built this cabinet as a replacement for me. His first build. The top is a piece of white oak with a live edge that was given to us more than a decade ago. I'm so pleased!

I made this for my 5 year old niece for Christmas...she loved it! Got a big hug without her parents saying a word.

Considering it's only my third woodworking project I was pleased with the results. Her Mom has requested one for London's baby brother; if I learn from my mistakes that one should be even better.

I painted all of the pieces separately before assembly, so the project was spread out over several days. If you're good enough to paint it all at once it's a weekend project.

My wife and I decided to build this with the same intent as Ana, to use as a changing table for our baby due in January 2015. We haven't built the topper yet but we're thrilled with the console table!

We did a lot of research on lumber before purchasing and ended up going through a local lumberyard, Gilcrest-Jewett for all but the pine 1x's which were purchased from lowes since the lumberyard didn't stock them in as many varying lengths and would have to mill them all from 1x4's. We used white birch purebond plywood. I understand Home Depot also carries this brand and may have been a little cheaper but the lumberyard cut all the pieces. Since we don't have a truck, hauling two 4x8' sheets of plywood wasn't an option and they can be super accurate with their wall saw. Totally worth it. 

The instructions for the doors say to use glue and nails but we took it a step further and secured each board to the one before it using pocket holes, in addition to the glue. We then covered the pocket holes with the 1x3's, securing with 1 1/4" finish nails. 

This was our first experience with edge banding and it really makes everything look so much more professional. If I were to give any tips, I would say to put it on the fronts of the shelf before putting the 1x2" frame in place so you can hide it, and also that I found it to be easier to use my sheet sander to get the edges off instead of a razor blade as the instructions suggest. 

This was also our first experience with doors. I found that paint sticks work well to achieve that perfect gap around the edges. I should have measured and not assumed but we ended up having to add a piece in the middle of the two doors because the 1x3's (typically 2 1/2" wide) were just under 1/8" too narrow. Make sure you measure those boards before putting it all together. 

In the end, we're thrilled with how this turned out. It's a real solid piece of furniture that's made to last. We actually looked at this piece at a West Elm and the floor model felt flimsy and thrown together. Great plans, thanks Ana!

We recently moved to Texas from Virginia and downsized in living space. Our 3 1/2 year old son had his own playroom so unfortunately we don't have an extra room for that any longer. My solution to that problem was building this loft bed. We altered the plans to fit our measurements (smaller bedroom). We also made it taller so we could use it longer. Also we didn't have a keg jig so we invested in that within that $200 cost. My husband and I built this in one evening from start to finish. 6pm to 2 am! This was also our first wood project. Not bad I say!

We are on a tight budget so this was built total from scrap lumber from when we removed a wall in our house and a few other scraps.  So the dimensions didn't turn out exactly right but that was my fault.  Thanks for sharing your plans.  My girl is going to love it!  

Just finished this project...took a little longer than I expected...it was a low cost project...I had most of the stock...but probably would cost around $75 to make. Paint and stain were the most expensive items. This was a lot of fun to make...Now to make the matching table...LOL

I used the "square x bass pedestal" plans to complete this 4' card table. The top is made from reclaimed gym flooring from the local high school. The "x base pedestal" provides a nice sturdy base for the large table. The project was completed over several weekends when I had time to work on it. 

From Closet to Reading Nook ... it took me a month from start to finish to complete and worth every minute spent on it! Come by to see the full story ...

http://www.joy2journey.com/2013/01/01/reading-nook-before-and-after/

No plan was needed for this project, just imagination :)

Hugs and Happy 2013!
Bj
http://www.joy2journey.com

The kitchen remodel left me with 400sqft of old-growth-pine laying around(60year old subfloor). While still pine, this was too good to throw away. So I decided to build a kitchen table and some benches.

Given these were old tounge and groove 2x6 I spent a lot of time with the planer, so hardly a weekend project. Further more I decided to use biscuit joints. The table probably took me like 5-6 weekends and the benches another 4...

My kids already managed to put some dents in the table, but that just makes it look more rustic.

fire pit bench

After building the Cabin Bunk system for my 5yo son, my wife wanted a buffet for our foyer. It took ma a Saturday to build and about $150 in materials.

Built using the plan except for removing the back angle supports and creating a top that resembles a live edge look.  Most of the build is done with pocket hole screws, glue and nails. 

We needed a way to store our 6 month old's toys in our main living area. We were previously keeping them in a pack and play and that wasn't going to cut it. We decided this plan would do the trick. It works even better than we anticipated. Built exactly the same as the plans with the same finish as well.