Community Brag Posts

I built this using the Kentwood bookshelf plans as a guide. I made my shelves 3 ft wide and made it aprox. 8 ft tall. I also bought the KREG shelf pin jig and built the shelves to be adjustable. I haven't chosen a finish yet because I am waiting for my son to pick a color since it is going in his room. I am considering fixing a shelf in place and building some doors for the bottom. I worked on this over a week span, however I could only do bits and pieces at a time. The sanding took longer than the build because I plugged the pocket holes and they take longer to sand down.

This bed is so perfect for my studio apartment. I don't have the floor space for multiple dressers, and the modular 3 bench design made it super easy to move in (and hopefully to move back out when school is over). LOVE LOVE LOVE this project.

I also made the headboard.
It is a single sheet of plywood, cut down and covered with polyfill and fabric. We predirlled holes for the buttons, and I set the headboard (fabric side up) across 2 saw horses with a flashlight underneath so I could see the drilled holes. I used nylon thread and a large needle to attach the buttons. There are flat buttons on the backsides of the holes so the thread doesn't slide through. It is hung directly on the wall behind the bed via wire hooks - make sure you hang it from the studs!

Needed a place to store wood for the fireplace and firepit. This very nicely organizes what was before a huge dirty pile of wood scattered on the ground. Cedar pickets for the top, all is coated in exterior white stain. Holding up nicely so far.

Love the desk! A few issues I had though are that the top panel will not go into the space of the top angle pieces are in place. I had to remove them to get it in. Additionally, the pocket holes seemed insufficient for the top 2x2s because of the angle they are at, so I went back and drilled countersink holes directly into the adjacent support board and added wool glue. Lastly, for then 2x2s that are supporting the bottom panel, I was worried about just having the pocket holes there as well because I could see my 5 year old climbing on it to reach the pegboard so I added L brackets to the bottom of the 2x2s under the bottom panel. I also added a light to the underside of the top panel and supports at the bottom near the floor. Turned out great 

I followed Anna's plans pretty closely though deviated somewhat as well. Added additional length and one more seat separators & seat, increased depth by a few inches, changed design of seperators to allow for arm rests, added some additional trim, a second inset shelf w/in the shoe box area (for sandals and whatnot), and then inset wainscoting.

Ana's little crates go perfect in our beach themed bathroom. I altered Ana's plans a little. I changed the dimensions to 12 x 11 1/4, and I did not use lath sticks for the crate slates because I wanted something sturdier. I had some left over 2×12 wood from a previous project, so I cut off 3/4 in wide pieces to make the crate slates. The wood grain gives character to the crates and makes it look more weathered.

These (matching set) were a pretty straightforward build based on the Reclaimed Wood Night Stands. http://ana-white.com/2011/08/reclaimed-wood-night-stand. The hardware I used was designed to match the Printer's Console that I built previously. I cheaped out on the drawer slides, which I wouldn't recommend doing because it gives the drawers a cheap feel to them. Plus, there's not that much of a price difference.

Substituted 1 x 4s for the shelves instead of the slats. Used red oak for the top and treated it with butcher block oils and wax so that it can be used for chopping.

I built this on my own (no help!) in my apartment garage from February 2011 - April 2011. I'm a single mom, so I would work an hour here and there every week or so.
The large pieces had to be cut by HD employees,Small pieces were all cut individually with a hand-saw. The only power tool I own right now is a drill, so this took a while. lol

When my husband and I bought our home we knew we wanted to make changes. The fireplace was an eye sore to us, so we decided to change the whole thing. When we researched on the net on how to make a mantel, we didn't find that many how to's. We have had a lot of questions on how we did it, so wanted to share with others how we did ours. Once we figures out how we were going to build it, it didn't take much time to finish the project. My blog has more details on how we accomplished our mantel. http://supersaturdayldscrafts.blogspot.com/2013/06/fireplace-remodel.ht…

Although Ive done a lot of DIY projects this was my first real furniture build. I modified the plans for the Simple White Outdoor Sofa because my back cushions were quite short and I didn't need the back to be so high to support them. I also liked the idea of having some contrast to the painted finish so used some Sapele I had. I'm really happy with the end result.

I wanted it to be a little more substantial that the original plans and I wanted the arms to be arms to fully support a forearm (and a beer) so I used 3 x 3 for legs and a 4 x 2 ripped down to 3 x 2 for the arms. I also tapered the legs to soften the lines a bit and give it a bit more interest.

The armchair is made in the exact same way but I made the legs a little taller so that the arms were at a more comfortable height to rest both arms on while reading a book or newspaper.

Love the way this turned out!

After seeing the farmhouse bed with stenciled headboard, I knew I wanted something similar for my little one. Haven't decided what I want to do with the big empty space in the middle of the headboard yet, but I went ahead and built it. I also changed up some of the decorative pieces just because I wanted her to have a one-of-a-kind bed. The blocks in the corners have little flowers in the middle, the legs at the end have slightly larger flowers on them to mimic the flowers in the blocks. I only made one major mistake on this bed, and that's the height of the headboard. For some reason it looked sooooo tall, so I stupidly decided to cut a few inches off of the legs, and now it's too short. Still mulling over what to do to fix that, but overall I love this bed!! :D It's the second thing I've built, the first being a bench.
Proud note: I built this bed completely and entirely by myself. :) If I can do it, anyone can!